Char-Broil 7201560 - Manuals

Page 2 - PARTS LIST; No need to go back to the store!; The store where you made your purchase; Call Grill Service Center for Help and Parts; • If you need assistance with your product or warranty

Key # Part Number Description Quantity A 55710232 SILVER SMOKE CHAMBER KIT 1 B 29001712 FIREBOX TOP 1 C 55710234 FIREBOX BOTTOM KIT 1 D 55710235 WOOD SHELF KIT 1 E 55700442 AXLE KIT 1 F 55700443 WHEEL KIT 1 G 55700183 LEG BRACE KIT 2 H 55710236 SMOKESTACK KIT 1 I 55710237 SHORT LEG KIT 2 J 55700186 ...

Page 4 - DO NOT FULLY TIGHTEN screws until Step 8 is complete.; Do not fully tighten screws

3 Lay the leg assembly on its side with legs braces pointing upward. Insert the wood rack hooks into leg holes and swing rack upward, parallel to leg braces. 4 With the aid of a helper, place leg holes of remaining leg assembly over wood rack hooks and rotate leg assembly until it meets the leg brac...

Page 5 - Insert a; cotter pin; Smoker chamber door not pictured; flange nuts; flange nuts inside chamber.; FULLY TIGHTEN ALL

6 5 Insert a cotter pin into the hole at one end of the axle and bend the ends of the pin back so that it cannot be removed. Slide a wheel onto the axle. Slide the axle through the holes at the ends of the short legs. Slide remaining wheel onto axle and secure with remaining cotter pin. Axle NOTE: S...

Page 6 - bolts; Diamond Fire Plate Installation; Second; The firebox should be slightly offset from the smoker; flat washer

7 8 Attach Firebox Top Assembly to Firebox Bottom Assembly using eight 1/4-20x3/4” hex-head bolts as shown below. NOTE: Smoker chamber and firebox doors not pictured for clarity. TM TM Diamond Fire Plate Installation - For models without Diamond Fire ignitor accessory, part number 22504850. TM For m...

Page 7 - wood handle spacers, fiber washers; and

9 10 Smokestack Smokestack plate NOTE: Smoker chamber door not pictured for clarity. From inside the smoker chamber, slide the smokestack through the large hole. Align the two holes in the smokestack plate with the holes in the chamber and secure with two 1/4-20x3/4” hex-head bolts outside the chamb...

Page 8 - Do not fully tighten

11 12 NOTE: Smoker chamber door not pictured for clarity. Install grate support screws in the four rear holes and two front-center holes in the smoker chamber. Use six #10-24x1” screws and #10 flange nuts . NOTE: Smoker chamber door not pictured for clarity. Attach shelf brackets to outer holes on f...

Page 10 - logo plate clips; onto pins until snug against inside of door.

16 15 Hang grease clip from holes on bottom right side of smoker chamber. A 12 oz. soup or vegetable can will fit nicely into clip to collect grease. Grease Clip If logo plate is not already installed, insert logo plate pins into two holes in lower right corner of smoker chamber door. Press logo pla...

Page 11 - Smoker chamber door not pictured for clarity.; Firebox side door not pictured for clarity.

18 17 NOTE: Smoker chamber door not pictured for clarity. If you wish to grill in the smoker chamber, place two of the three wire fire grates into bottom of smoker chamber. Place two large porcelain cooking grates into chamber, resting them on the grate support screws. Large Porcelain Cooking Grate ...

Page 13 - WARNING; MOST SURFACES ON THIS UNIT ARE HOT WHEN IN USE.; HARDWARE LIST

WARNING MOST SURFACES ON THIS UNIT ARE HOT WHEN IN USE. USE EXTREME CAUTION. KEEP OTHERS AWAY FROM UNIT. ALWAYS WEAR PROTECTIVE CLOTHING TO PREVENT INJURY. HARDWARE LIST Hardware is shown actual size. You may have spare hardware after assembly is complete. #10-24x1” Machine Screw Qty: 16 #10-24x1¾” ...

Page 14 - Preparing and Using Your Silver Smoker; GRILLING; • Remove the ash after each use.

Preparing and Using Your Silver Smoker Before cooking with your Silver Smoker, the following steps should be closely followed to both cure the finish and season the interior steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors to your first foods. 1. Bru...

Page 15 - 0 Days LIMITED warranty; parts replaced under the terms of this limited warranty.; ITEMS MANUFACTURER WILL NOT PAY FOR:; Limited Warranty

Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase. The manufacturer reserves the rig...

Page 16 - Printed in China