Char-Broil 463262811 - Manuals

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

7 WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NE...

8 Match-Lighting CAUTION If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury. Turn contr...

9 CAUTION Storing Your Grill •Clean cooking grates.•Store in dry location.•When LP cylinder is connected to grill, store outdoors in a well- ventilated space and out of reach of children. •Cover grill if stored outdoors. Choose from a variety of grill covers offered by manufacturer. •Store grill ind...

3. Remove carryover tubes and burners. 4. 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the oneeasiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner tube...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. 12 Key Qty Description A 1 BOTTOM SHELF B 1 TANK SCREW , F/ BOTTOM SHELF C 2 CASTER, LOCKING D 2 CASTER, FIXED ...

ASSEMBLY 2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole must be on Right side of bottom shelf. 7mm lock washer 7mm flat washer 14 Left side panel (with large hole) Make sure s...

3 4 Place lower back panel between side panels at rear of bottom shelf. Make sure the slots are positioned as shown (A). Secure lower back panel to side panels using two 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side. A Lower back panel 1/4-20x1/2” screw 7mm lock washer 7mm ...

7 17 Insert flange on right side shelf into side shelf brackets on side of firebox, shown A . Attach rear of shelf using one 1/4-20x3/4” screw, 7mm lock washer, 7mm washer and 1/4” nut in upper hole; using one flat 1/4-20x1½” screw, 7mm lock washer and 7mm flat washer in lower hole, shown B/C . two ...

8 18 Insert tabs on left sideburner shelf assembly into rectangular slots in side of firebox, shown A. Attach rear of shelf using one 1/4-20x3/4” screw, 7mm flat washer, 7mm lock washer and 1/4” nut in upper hole; and using 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer in lower hole, shown B/C ...

9 Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POS...

8a 11 20 #10-24x3/8” screw Sideburner lid Place sideburner lid onto left shelf and align holes in back of lid with hinge holes. Secure lid to hinges using four #10-24x3/8” screws, 5mm flat washers, 5mm lock washers, and #10-24 hex nuts. NOTE: Fully secure one hingewith screws, washers and nuts,then ...

13 A 21 Inside of cart, insert heat shield rear tabs(without holes) into slots between upper and lower back panels. Then insert left and right grease tray rails into slots beneath grease tray opening in upper back panel. Then insert end of tank wire into right arcuate slot on lower back panel, shown...

14 Inside of cart, insert tank exclusion wire shelf ends into lower back panel, shown A . Attach front left side of wire shelf to the left side panel with one #8-32x3/8” screw, 4mm lock washer and 4mm flat washer. one #8-32x3/8” screw, Attach leg to bottom shelf with 4mm lock washer and 4mm flat was...

15 B 16 23 Place sideburner grate and griddle onto sideburner shelf. Sideburner grate Sideburner griddle Release the cap and nut from electronic ignition module. Attach electronic ignition module to the cart right side panel with back of the electronic ignition module. Total (2) connections, shown A...

18 24 17 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox. Flame tamer Pin Slide into slots Hinge pin on bottom of door Top of door PRESS Right door Front brace Insert hinge pin on bottom of doors into hole...

20 25 On back of right side fascia, open battery box by sliding its cover. Put two AA batteries in the box and then replace the cover. 19 Battery box AA battery Cover Place cooking grates onto the firebox as shown. Insert the two wire ends at rear of warming rack into holes in back of firebox. Front...

21 22 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill. Secure cylinder wi...

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire ...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP c...

Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when Electronic Ignition Button is pressed; no noise can be heard from spark module. SECTION II SECTION III Sparks are present but not at all electrodes and/or not at full strength Possible Cause • ...