Char-Broil 463247412 - Manuals

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

Safety Tips s Before opening LP cylinder valve, check the coupling nut for tightness. s When grill is not in use, turn off all control knobs and LP cylinder valve. s Never move grill while in operation or still hot. s Use long-handled barbecue utensils and oven mitts to avoid burns and splatters. s ...

Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW . You should see a smaller flame in LOW position than seen on HI . Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sud...

Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn gas OFF at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. 3. Remove carryover tubes and burners. 4. 5. Carefully lift each b...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. 11 Key Qty Description A 1 BOTTOM SHELF B 1 TANK SCREW , F/ BOTTOM SHELF C 2 CASTER, LOCKING D 2 CASTER, FIXED ...

PARTS DIAGRAM QQ 12 BB S RR SS SS TT GG DD WW EE HH II JJ OO PP FF UU VV VV XX VV UU UU OO NN LL MM MM KK CC Z AA YY Z Z X X X X Y W O AAA AAA P O O Q Q N A B C E F H V I K L M J R D D G C U Y Y Y T ZZ

2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole must be on left side of bottom shelf. 7mm lock washer 7mm flat washer Locking caster Bottom shelf Non-lock caster Rear Front Lef...

3 4 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Place lo...

On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps. 5 15 ...

7 6 1 Now you may fully tighten lower screws on upper back panel. 1/4-20x3/4” screw Back of main control panel Control panel Fascia, left sideburner shelf Left sideburner shelf Flange into Brackets Bracket 1/4-20x3/4” screw screw washer washer 7mm flat #8x3/8” self-tapping large flat washer 7mm lock...

11 Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1 ½ ” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD ...

13 19 *This side UP Tank heat shield 12 Inside of cart, insert rear shield tab into left slot on upper of lower back panel. Attach front shield tabs under front brace and attach right and Insert left and right grease tray rails into slots left rails under front brace with three #8x3/8” self-tapping ...

15 20 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox. Back of firebox Front of firebox Note: Some parts omitted for clarity of illustration Flame tamers Pin 14 Insert hinge pin on bottom of doors into hol...

On back of grill, slide grease tray into opening in upper back panel. CAUTION Failure to install grease tray will cause hot grease to drip from bottom of grill with risk of fire or property damage. . 16 17 21 Assembled warming rack Place cooking grates onto the firebox as shown. Insert the three wir...

Unscrew on cart right side panel. Insert AA battery into ignitor, negative (—) end first. Replace the cap. electronic ignition cap – 18 22 AA Battery Electronic Ignition Cap + - . 19 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use &am...

DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire comin...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP c...

Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when Electronic Ignition Button is pressed; no noise can be heard from spark module. SECTION II SECTION III Sparks are present but not at all electrodes and/or not at full strength Possible Cause • ...