Cavaliere SV218B2-30-BLK - Manuals

Page 5 Venting Requirements Vent system must terminate to the outside • (roof or side wall). DO NOT terminate the vent system in an at - • tic or other enclosed area. DO NOT use 4” (10.2 cm) laundry-type wall • caps. Use metal/aluminum vent only. Rigid metal/ • aluminum vent is recommended. DO NOT u...

Page 6 Duct Run Calculation: Recommended maximum run 6” or 3-1/4 x 10” duct 50 ft Vent piece deduction Each 90º elbow used 9 ft Each 45º elbow used 5 ft Each 6” to 3/14 x 10” transition used 7 ft Side wall cap with damper 0 ft Roof cap 0 ft Duct Run Calcuation example: One roof cap, two 90º elbow, a...

Page 7 Ductless Conversion Ductless conversion is intended for applications where an exhaust duct work is not possible to be installed. • When converted, the hood functions as a purifying hood rather than an exhaust hood. Fumes and exhaust from cooking is drawn and filtered by a set of charcoal filt...

Page 8 Electrical Requirements NOTE: The charcoal filters are preinstalled if you purchased the range hood with re-circulating kit from us. Remove aluminum filters on hood. 1. Position the charcoal filters onto each side of the motor and turn until it locks. Re-install aluminum filters. 2. Charcoal ...

Page 9 Figure 1 Figure 2 WARNING Severe Injury Rotating fan can cause severe injury. Stay clear of fan when motor is running. Preparation WARNING Excessive Weight Require three or more person to move and install this range hood. Spinal or other bodi- ly injuries could occur if it is not followed. Ad...

Figure 5 Slide up and secure upper chimney to mounting bracket Hold in position and secure lower chimney to range hood Fasten mounting bracket Secure upper support frame Figure 3B Figure 3A Figure 4 Page 10 Installation Installations (refer to Page 4 & 11 for parts) : Measure the distance betwee...

Page 11 Upper chimney Wall mount range hood Lower chimney Motor housing Electric circuit box (Location varies) 6” Round duct (exhaust) Re-circulating kit exhaust (Re-circulating kit not shown) Duct work and electric wiring region Note: Type “A” anchors are designed for dry wall. Not to be used with ...

Page 12 Control Panel Layout and Buttons Configurations: Power Decrease Value Light Increase Value Blower Power Indicator Blower Speed Indicator Power-On Elapsed Digital TimerPower-Off Delay Digital Timer Power-Off Delay Timer Indicator Light Power Indicator Range Hood Operations This range hood is ...

Page 13 Control Panel Layout and Buttons Configurations: Controls: • Adjusting the timer function: • While the blower (motor) is not running, press and hold • Decrease Value button over 3 seconds to enter timer mode. Adjust to desired period of delay off timer by pressing Increase Value or Decrease ...

Troubleshooting Page 14 If the range hood or halogen light does not operate 1. after installation: Check if the range hood has been plugged in, make • sure that all power has been turned back ON, fused not blown and all electrical wiring are properly con - nected. Swap out light assembly to working ...

Page 15 Specifications * : Body Stainless Steel / Tempered Glass Power Rating 220V/50Hz or 120V/60Hz (USA & Canada standard) General Input Power 288 W (218W + 2x35W) Motor Input Power 218 W Motor Revolution 600 RPM (±10%) to 1800 RPM (±10%) Levels Of Speed Control 6 Levels Maximum Airflow 900 CF...

Page 16 Wiring Diagram Six Speed with Type GU10 Bulb Six Speed with Type MR16 Bulb

SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating! For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will help preserve the appearance of the range hood. Cleaning Exterior surfaces: Clean pe...

Page 18 One Year Parts Warranty: For one year from the date of original purchase, your local reseller will provide free of charge, non-consumable replace - ment parts or components that failed due to manufacturing defects. Subject to the conditions and limitations set forth below, your local reselle...

Page 19 Carefully inspect all items for damages before accepting delivery. note any damages on the freight bill or express receipt. request name and signature of the carrier’s agent and keep copy to support your claim. Upon acceptance of items, owner assumes responsibility for its safe arrival. Repo...