Casio V-R7000- Manuals

E-7 Europe Manufacturer:CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union:CASIO EUROPE GmbH CASIO-Platz 1, 22848 Norderstedt, Germany Please keep all information for future reference. The declaration of conformity may be consulte...

E-8 Precautions for Use Read the following items thoroughly and use this product properly. CASIO bears no responsibility whatsoever for malfunction or damage caused by handling not following below contents. Please note that it will also result in charged repair, and actual cost required for repair w...

E-9 Take Advance Notice of the Following ● The content of this manual may be changed without prior notice due to improvement or specifi - cation change of the product. ● Please note that CASIO bears no responsibility for damage, loss of profit, or any claim from third party due to loss or change of ...

Basic Operation E-11 Basic Operation This chapter describes about the basic operation method of this product after the installa-tion. Name of Parts and What They Do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-12 Power ON/OFF . . . . . . . . . . . . . . . . . . . . . ....

E-12 Name of Parts and What They Do * The operation of the various parts is described with reference to the illustration of the display mounted on the stand. <Front> 2 1 3 4 5 1 Indicator Display the status of the power supply. 2 Power switch Turn the power ON. It will display the shutdown men...

Basic Operation E-15 Power ON/OFF This product has 3 power switches, the main power switch, power switch, and the OFF switch. Daily Use Turning the Power ON 1. Press the power switch. The screen will turn on. Turning to sleep mode 1. Press the power switch while the power is ON. The screen will turn...

E-16 Power ON/OFF Moving and Cleaning When moving or cleaning the product, always shut down the main unit before turning OFF the main power switch. Also, always make sure that the main power switch is OFF before removing or inserting the plug. 1. Shut down the main unit. Using the OFF Switch (1) Pre...

Basic Operation E-17 Description of the Indicator The status is indicated by the ON, flashing, or OFF of the indicator. Indicator Indicator Status Green light is ON Power is ON/screen is ON Orange light is ON Power is ON/screen is OFF Green and red lights flashing with screen ONRed and orange lights...

E-18 Adjusting the Angle of the Display Adjust the angle of the display to the appropriate position for comportble operation. 1. Loosen the tilt knob in the direction indicated in the illustration for 1 rotation or more and raise the top of the stand. + Take caution not to pinch finger with the tilt...

Installation E-19 Installation This chapter is about the installation. Please read these instructions before starting installation. During use of the product, read these instructions if you have disconnected the cables of the product to move it and do not know how to reconnect them. Name of Parts an...

E-22 Connecting the Power Supply and Various Devices Connect the power supply and devices to be used. + Keep the main power switch in OFF position until all the connections are completed. ● Use a Phillips screwdriver and pliers to make the connections. Prepare in advance. ● Work with the touch scree...

Connecting the Power Supply and Various Devices E-23 Installation Connecting the AC Adaptor 2. Route the cable through the stand and connect the AC adaptor to the DC jack located within the back of the display. Connecting Other Devices Connect the optional device to the following connector. Option C...

E-24 Connecting the Power Supply and Various Devices Insert the SD Card (1) Insert the SD card, front-side up, into the SD/SDHC memory card slot located within the back of the display. Connecting the HDMI Device (1) Connect the HDMI cable to the HDMI port within the back of the display. 3. After com...

Connecting the Power Supply and Various Devices E-25 Installation Preparing the Stand 1. Loosen the tilt knobs by turning them through at least 1 full rotation in the directions shown. 2. Raise the upper part of the stand. Then, while holding it steady, secure it by tightening the tilt knobs one sid...

E-26 Connecting the Power Supply and Various Devices Setting the Stand and the Display 1. Loosen and remove the screw for the cable fastener at the bottom of the opening of the stand with a Phillips screwdriver. 2. Route the connected cables into the stand, passing them through the opening. Remove t...

Connecting the Power Supply and Various Devices E-27 Installation 4. Fasten the stand to the display with 4 screws. 5. Attach the rear cover to the stand in the direction of the arrow. 6. Loosen and remove the screws for the 3 cable fasteners at the bottom of the stand with a Phillips screwdriver. 7...

E-28 Connecting the Power Supply and Various Devices 8. Raise the display. Then, while holding it steady, secure it by tightening the tilt knobs one side at a time in the directions shown. 9. Connect the AC adaptor with the power cord, and plug into a power outlet. Installation features • A screen f...

Connecting the Power Supply and Various Devices E-29 Installation • The display may be wall-mounted. In this case, the stand is not used. For further details, contact the CASIO service representative. MCR Unit (VA-B46MCRE) Installation + Before installation, be sure to turn the main power switch OFF...

E-30 Specification Item Specification Model V-R7000/7100 Display Type 15.6 inch WXGA color TFT liquid crystal display Resolution 1366 x 768 Backlight White LED Touch panel Method 4-wire resistive film Size 15.6 inch Wireless LAN (V-R7100 only) Standard IEEE 802.11a/b/g/n Bluetooth (V-R7100 only) Sup...