Casio QV-5000SX- Manuals

Casio QV-5000SX– User Manual, Manual in PDF format online.

Manuals:

User Manual
Manual

User Manual Casio QV-5000SX

Summary

Page 2 - CONTENTS

CONTENTS SPECIFICATIONS ....................................................................................................................................... 1 BLOCK DIAGRAM ...............................................................................................................................

Page 3 - SPECIFICATIONS; Item

— 1 — SPECIFICATIONS Item Specification Recording System Digital (JPEG base); PC Link software can be used to input images in CAM, JPEG,TIFF and other format. Recording Medium Flash memory (8MB) Memory Capacity/ SUPER FINE: 16 images Computer Output image (450KB compressed – 1280 x 960 pixels)FINE: ...

Page 4 - BLOCK DIAGRAM

— 2 — BLOCK DIAGRAM ST-UNIT C-PCB High voltage generator Lens UNIT BatteryVoltage Xo LAMP D-PCB AF-PCB PW-PCB KA-PCB sensor Comparator Voltage Controller V oltage Controller 3.3V VCC3-1VCC3-2VCC3-3 12.75V VCC13 7.5V VCC7 5.0V VCC2 –14.5V VEE2 3.0V VDD B, G R/VIDEO AGND5 VCC5-1CSYNC VOUT SGND VA LTTR...

Page 5 - POWER SUPPLY FLOW

— 3 — PW2=H PW2=L (BLCONT=L PWCONT=L) PW2=H (PWCONT=H CSYNC Start BLCONT=H) (2) REC MODE, LCD ON POWER SUPPLY FLOW When power is turned on, the power supply flows in each mode are as shown below. (1) PLAY MODE (3) REC MODE, LCD OFF PW2=H PW2=L (BLCONT=L PWCONT=L) (PW1=H PW3=H) PW2=H (PWCONT=H CSYNC ...

Page 6 - VOLTAGE TABLE; PCB

— 4 — VOLTAGE TABLE PCB D C AF ST L Signal VCC1-3 EVCC3 VCC3 VCC3-1 VCC3-2 VCC3-4 VCC5-1 VCC18 VCC15 VCC5-4 VCC3 VCC3-1 VCC3-3 VEE7 VCC5-2 VCC5-3 VCC3-1 VCC1-ST VCC5-1 F.B. VCC13 VCC7 VCC2 VEE2 VDD VCC5-1 VCC3-1 BL-VCC Control signal (“H” active) Non, Sw, Non, Sw, PW0 PW0 PW0 PW2 PW1 PW1 PW3 PW0 PW0...

Page 7 - ADJUSTMENT; does not indicate malfunction.; -2. White balance · Sensitivity adjustment; filters are lined up.

— 5 — PC RS232C port Link cable QV-5000SX ADJUSTMENT 1. Complete Unit 1-1. Loading ADJ Set QV-5000SX to “PLAY” mode. (1) Connect QV-5000SX and DOS/V PC with link cable.(2) Execute the adjustment software shown below on PC. DT777E - aok 98042101.adj ENTER (3) During the procedure, “MEMORY ERROR#4” ap...

Page 9 - -3. Flash operation and recharge operation; Flash lens face

— 7 — 1-3. Flash operation and recharge operation • Apply 6.0 ± 0.1 V voltage on DC in jack. • Set QV-5000SX in “REC” mode.• Perform after flash adjustment. (1) Shoot a picture with flash ON.(2) Shoot in red eye reduction mode.(3) Shoot in macro mode.(4) Set QV-5000SX in “PLAY” mode and check the pi...

Page 10 - Flash trigger waveform; TIME

— 8 — Flash trigger waveform 1. Normal waveform TIME : 1 µ sec/DIV VOLTS : 1 V/DIV (2) When trigger skipping occurs on the first negative pulse. ACQUIRE NORMAL 1 ENVELOPE 2 AVS REPET ON | OFF SAVE ON ON | OFF CH1 1V 757 µ V UERT 1 µ V First positivepulse. First negativepulse. OK if second positive p...

Page 11 - Reference: • Current consumption of REC mode.

— 9 — 1-4. Current consumption Set QV-5000SX to “PLAY” mode. (1) Current consumption (DC in = 6.0 ± 0.1 [V]) (2) Lower the voltage from 6 V as shown below then make sure the battery warning indicator changes. DC in = 5.0 ± 0.05 [V] (PLAY mode) DC in = 4.65 ± 0.05 [V] (PLAY mode) Note: Make sure that...

Page 12 - TEST MODE

— 10 — 1-6. Test mode (1) Turn power ON while pressing shutter button and DISP button simultaneously. TEST MODE display is displayed. In the center of the display “TEST MODE” is displayed at 4 times the size of other letters.In the lower right corner PATCH, LOADER, ADj and Program version are displa...

Page 14 - Do not use 5 to 9 of MENU2 because it will corrupt data stored.

— 12 — MENU2-1 MENU2-2 MENU2-3 MENU2-4 Execute CCD color solid adjustment, then record it on ADJ of flash memorydisplay.Press shutter button by adjusting the light amount using specified filters inspecified viewer.When setting mark is displayed it is completed. Execute CCD sensitivity check, check r...

Page 15 - Clock frequency check; Make sure SYSCLKP terminal is at f0 = 54MHz; Make sure RGB and VIDEO are outputted.; For VIDEO, check each of NTSC type and PAL type.

— 13 — 2. D-PCB Assy 2-1. Operation check • Set QV-5000SX in “PLAY” mode.• Connect C, L, PW, KA, KB, JK, BL PCB.• Connect PACT (CP510) to GND for short time (1, 2 seconds). Then the unit will be operation mode.Supply electricity to each power source of D PCB. VCC3-1; 3.3 ± 0.08V VCC5-1; 5.0 ± 0.1V E...

Page 17 - Adjust VCC15 after adjusting VCC18.

— 15 — Power Supply L-PCB 3.3 V VCC1-L PW~3 VCC18 VCC15 VEE7 V 3. L-PCB Assy 3-1. VCC18, VCC15, VEE7 voltage adjustment • Make sure VCC1-1 (CP149) = 5.0 ± 0.05 [V] • Apply 3.3 V ± 5 % to PW0 to PW3. (1) Apply 5.0 ± 0.05 V to VCC1-1 and adjust VR120 so that VCC18 (CP121) becomes 18.5 ± 0.5 V. (2) Adj...

Page 18 - DISASSEMBLY; hook

— 16 — DISASSEMBLY 1. Unscrew two screws (S4) on the side. 2. Unscrew a screw (S4) on the bottom. 3. Open battery cover. 4. Release the hook on the side. 5. Use a (–) screwdriver to remove the small hook. 6. Remove the upper case. 7. It should look like this. 8. Remove the top case by lifting it up....

Page 20 - under the insulation sheet.

— 18 — 17. Bottom view (LCD) 18. Bottom view (camera) 19. Peel off the insulation sheet. 20. Unscrew two screws (S9) of KA PCB hidden under the insulation sheet. 21. Remove a screw (S1) of KB PCB. 22. Remove KA PCB and KB PCB. 23. Unscrew two screws (S1) of the flash unit. 24. Remove the flash unit....

Page 21 - Peel off insulation sheet of lens ass’y.

— 19 — 25. Unscrew screw (S8) of PW PCB and remove washer. 26. Unscrew screws (S8) and (S1) and remove washer. 27. Remove the battery spring. 28. Remove PW PCB and JK PCB. 29. Unscrew a screw (S5) of battery holder. 30. Remove battery holder. 31. Peel off insulation sheet of lens ass’y. 32. Unscrew ...

Page 22 - bling be sure the contact is secure.

— 20 — 33. Remove flash unit. 34. Unscrew a screw (S2) from metallic part on D PCB. 35. Remove connector (CN540). When assem- bling be sure the contact is secure. 36. Remove D PCB. 37. Unscrew two screws (S1) of lens ass’y. 38. Remove lens ass’y. Remove a screw (S2) of L PCB. 39. Remove L PCB. 40. U...

Page 25 - EXPLODED VIEW

— 23 — 1 S1 S1 63 S7 61 5 12 S1 S7 60 59 2 S7 58 S2 9 54 S9 14 15 18 37 38 50 43 19 46 53 44 3 13 30 29 24 32 S2 10 S8 8 S2 S1 55 56 62 S2 S2 6 11 S5 17 S4 S4 S6 36 S8 4 31 26 28 22 40 32 20 21 41 25 27 49 52 33 S3 39 S9 51 35 42 47 S4 E1 23 34 45 48 16 7 57 EXPLODED VIEW

Page 26 - PART PRICE LIST

DIGITAL PCB ASSY N Item Part No. Part Name Specification Q Price Code R Ics N IC400 2105 6486 IC S-80835ANNP-EDZ-T2 1 AC C IC410 2105 5215 IC TC7W74FU(TE12L) 1 AE C IC412 2114 4676 IC TC7W04FU(TE12L) 1 AD C N IC414 2105 6472 IC TC74AC00FT(EL) 1 AF C N IC415 2105 6244 IC TC7S32FU(TE85L) 1 AC C N IC42...

Page 31 - STROBE UNIT

MAIN BODY COMPONENT N Item Part No. Part Name Specification Q Price Code R N 1 1014 9879 STROBE UNIT CO-777 1 CN A 2 2725 1347 DISPLAY ASSY/TFT LCD COD18T1022RN 1 DI A N 3 6613 0620 PANEL/REAR K140444-1 1 BT X N 4 6613 0830 PCB ASSY/JACK K341261*1 1 CN A N 5 6613 0831 PCB ASSY/BACK LIGHT K341261*2 1...

Page 34 - PRINTED CIRCUIT BOARDS

Page 39 - SCHEMATIC DIAGRAMS; DIGITAL CIRCUIT

Page 40 - POWER CIRCUIT

Page 41 - LINEAR CIRCUIT

Page 47 - TROUBLESHOOTING; • L board failure of JK board failure.; The film counter seems incorrect.

— 45 — TROUBLESHOOTING Trouble 1 : Display failure on Video/LCD display is OK. • Setting of NTSC/PAL is incorrect. ➠ Charge the video setting that is right for the TV (Refer to user ’s manual). • L board failure of JK board failure. ➠ Replace boards. Trouble 2 : Flash does not work. Unable to adjust...

Page 48 - FLOW CHART OF TROUBLE SHOOTING

— 46 — FLOW CHART OF TROUBLE SHOOTING Set QV5000-SX to REC mode. Turn POWER switch ON. Set QV5000-SX to PLAY mode. Does the power LED light? Does the sub LCD work normally? Does strobe charge work normallly? Does LCD work normally? Press shutter button half way to activate AF. Press shutter button c...

Page 54 - Overseas Service Division

CASIO TECHNO CO.,LTD. Overseas Service Division 8-11-10, Nishi-ShinjukuShinjuku-ku, Tokyo 160-0023, Japan