Page 2 - CONTENTS; Page
CONTENTS TE-M80 Page 1. SPECIFICATIONS ........................................................................................ 1 2. MACHINE INTIALIZATION .......................................................................... 3 3. BLOCK DIAGRAM ......................................................
Page 5 - MACHINE INTIALIZATION; -1. Initialization and loading memory protection battery; program the cash register.; toward the back of the cash register.; REPLACE MEMORY PROTECTION BATTERIES AT LEAST ONCE EVERY YEAR.; -3. To select date format and monetary mode
— 3 — 2. MACHINE INTIALIZATION 2-1. Initialization and loading memory protection battery Note: You must initialize the cash register and install the memory protection batteries before you can program the cash register. To initialize the cash register 1. Set the mode switch to OFF.2. Plug the power c...
Page 7 - Removing the register; Remove the journal cover and then the WINDING PULLY.
— 5 — 4. DISASSEMBLY ■ Removing the register 1. Remove the journal cover and then the WINDING PULLY. 2. Remove the battery cover and then the battery. 3. Remove the two screws. 4. Separate the main unit as shown below. Screws
Page 9 - Disassembling the display unit
— 7 — ■ Removing the switch PCB (E270-PR) 9. Remove the two screws. Lift up the PCB and remove the FPC and then the PCB. ■ Disassembling the display unit 10. Remove the display cover. Hooks 1 Hooks 3 Hooks 2 Hooks 4 (1) Open the printer cover and remove Hook1 and Hook2. (2) Remove Hook3 and Hook4. 1...
Page 12 - CIRCUIT EXPLANATION
— 10 — 5. CIRCUIT EXPLANATION 5-1. CPU (IC12: uPD784215AGC8038EU) 5-1-1. Pin Assignment 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 100 76 P120/RTP0 P121/RTP1 P122/RTP2 P123/RTP3 P124/RTP4 P125/RTP5 P126...
Page 17 - Stepping Motor Driver IC; Display Driver IC
— 15 — 5-5. Display circuit KC4 SENS1 SENS2 VP VP DATA LATCH CLOCK Vdd DST4 GND GND GND GND DST3 Vdd THERMISTOR DST1 DST2 VP VP nB B A nA KI2 KI1 KI10 LEDCOM0 LEDSTR VCC 1 IN2 5 OUT2 7 IN1 4 IN3 3 IN4 2 GND 6 OUT4 10 OUT1 8 OUT3 9 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 8 4 6 ...
Page 18 - Winding motor circuit
— 16 — 5-6. Winding motor circuit & Drawer circuit VC DRW PN2 PN1 1 2 P60/A16 73 P63/A19 76 P90 95 P61/A17 74 P127/RTP7 8 X2 10 P91 96 P37/(EXA) 93 P36/TI01 92 P34/TI2 90 P31/TO1 87 P30/TO0 86 P103/TI8/TO8 85 TEST/(Vpp) 94 P35/TI00 91 P92 97 P32/TO2 88 P01/INTP1 17 P05/INTP5 21 P52/A10 66 P04/IN...
Page 19 - DIAGNOSTIC OPERATION; To start the diagnostic program; ECR enters the diagnostic mode by the following operation.
— 17 — 6. DIAGNOSTIC OPERATION To start the diagnostic program ECR enters the diagnostic mode by the following operation. 1 Turn the mode key to PGM. 2 Input “99990000” and #2 (SUB TOTAL). Upon the above operation ECR prints the following and issues a receipt. * Note that the test mode will not boot...
Page 23 - E01 appears on the display.; Most common causes; Put in new batteries.
— 21 — 7. TROUBLESHOOTING 1 2 3 4 5 6 7 8 Symptom/Problem E01 appears on the display. When the printer does not printproperly. No date or time on receipt.Paper is not advancing enough. Key won’t turn to Z, X, PGM andRF modes. Drawer opens up after ringingup only one time. Not clearing totals at end ...
Page 32 - to
— 30 — KEYBOARD (TE-M80/PCR-T265/PCR-T275) 5 20 17 18 6 to 17 6 20 18 22 21 19 23 18 22 22 to 19 24 27 26 25 28 21 23 22
Page 47 - Overseas Service Division
CASIO TECHNO CO.,LTD. Overseas Service Division 6-2, Hon-machi 1-Chome Shibuya-ku, Tokyo 151-8543, Japan