Casio HA-A34AT- Manuals

E-4 Safety Precautions This wireless transmitter uses the 2.4 GHz band. It employs the FH-SSmodulation system and has an interfering range of 20 m. This wireless transmitter uses the 2.4 GHz band. It employs the DS-SSmodulation system and has an interfering range of 40 m. Operation of Wireless Data ...

E-10 Safety Precautions AC Adaptor Caution • The housing of the AC adaptor can become warm during normal use. • Take normal precautions against electric shock. • At least once a year, unplug the AC adaptor from the wall outlet and cleanany dust that builds up between the prongs of the plug. Dust bui...

E-11 Operating Precautions Your Handheld Terminal and its options are precision digital instruments. Improperoperation or rough handling can cause problems with data storage and other problems.Note and observe the following precautions to ensure proper operation. • Do not continue operating the Hand...

E-12 Important • The contents of this guide are subject to change without notice. • Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or any thirdparties for any losses or damages arising from the use of this guide. • Although the utmost care has been taken in preparing this manual,...

E-16 Contents Safety Precautions ............................................................................................ 1 Operating Precautions .................................................................................... 11 Important .......................................................

E-18 Install the mainbattery Before Getting Started Be sure to perform the following steps before using the Handheld Terminal for the firsttime. Handheld Terminal Wrist Strap User's Guide (this manual) Large-capacity battery pack Cover When unpacking, make sure that all items are included. Open the ...

E-19 Install the main battery When Using the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U only) 1. Install the AA size alkaline batteries. 1 Slide the two main battery cover lockswitches on both sides of the HandheldTerminal to the “FREE” position, andremove the main battery cover. 2 In...

E-20 When Using the Battery Pack Charging is required when using the battery pack (HA-A20BAT or DT-5025LBAT) soldseparately.Use the Dual Battery Charger when charging the battery pack before installing in theHandheld Terminal, or use the Cradle-type Battery Charger or Cradle to charge afterinstallin...

E-21 3 Return the main battery cover to itsoriginal position as shown in theillustration, and return the two mainbattery pack cover lock switches to the“LOCK” position. When loading a large-capacity batterypack, attach the large-capacity batterypack cover. • Make sure the battery pack removaltape is...

E-22 Handheld Terminal System Configuration Options DT-X5 Series HA-A60IOHA-A61IO Bridge Satellite Cradle (HA-A61IO)Bridge Basic Cradle (HA-A60IO) Cradle-type Battery Charger HA-A30CHG Laser Scanner models The laser scanner modelsare not available in theUSA and Canada. • DT-X5M10E • DT-X5M10R C-MOS ...

E-24 Cables DT-887AXA DT-888RSC DT-380USB Bridge Satellite Cradle Cable/RS-232C Dsub-9Pin (Female) RS-422 Modular Cable USB Cable Handheld Terminal System Configuration DT-X5_E_P18_24.p65 04.7.14, 6:02 PM 24

E-25 1 Indicator 1 2 Indicator 2 3 LCD Panel 4 Power Key 5 L Key 6 R Key 7 Cursor Key 8 Multi Key 9 Numeric Keys 10 Execute Key This indicator is green when charging is completed, and redduring charging. This indicator is green when the bar code has been read successfully,and red when a reading erro...

E-27 Replacing the Battery Your Handheld Terminal uses two types of battery: main battery and a memory backupbattery. AA size alkaline batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U) or the battery packis used for the main battery. There are two types of battery packs that can be used,consisting of the ba...

E-29 To replace the battery pack 1. Make sure that the Handheld Terminal is turned off. If the power is on, press the power key to turn it off. 2. Turn over the Handheld Terminal. 3. Slide the two main battery cover lock switches on both sides of the HandheldTerminal to the “FREE” position, andremov...

E-32 Removing and Installing the Alkaline BatteryHolder (DT-X5M10E/DT-X5M30E/DT-X5M30U only) Removal Procedure When using a battery pack, first remove the alkaline battery holder according to thefollowing procedure. 1. Make sure the Handheld Terminal is turned off. If the power is on, press the powe...

E-33 1 2 2 1 1 Installation Procedure When using AA size alkaline batteries, install the alkaline battery holder according to thefollowing procedure. 1. Make sure the Handheld Terminal is turned off. If the power is on, press the power key to turn it off. 2. Turn over the Handheld Terminal. 3. Slide...

E-34 Attaching the Wrist Strap Be sure to attach the wrist strap and use it to protect against dropping the HandheldTerminal when carrying it around.Attach the wrist strap by following the procedure described below. 1. Pass the thin cord of the wrist strap through the wrist strap hole on the back of...

E-35 Configuring Handheld Terminal Settings Adjusting Display Contrast Perform the following steps to adjust display contrast to make display more vivid andeasier to see. • Press the “Fn” key and then press the “2” key or “3” key after confirming that“F” is displayed in the lower right corner of the...

E-37 Warning Label • This label is a warning label for Class 2 laser products thatcomply with IEC60825-1+A2:2001 CAUTION • Use of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure. • The laser light emitted by this laser s...

E-41 Emission Width Adjustment Bar code Important! • An error message is displayed when emission width has not been adjustedproperly. Repeat the adjustment procedure when this message is displayed. 4. After checking that the laser light is at the proper position, depress the trigger key for about 1 ...

E-42 Performing Communication IR Communication IR communication can be used to transfer data between two Handheld Terminals.When performing IR communication, orient the IR ports of both Handheld Terminals sothey are pointing directly at each other.The ports can be in direct contact with each other, ...

E-43 Bluetooth TM Communication Bluetooth TM protocol can also be used to transfer data between two Handheld Terminals. With Bluetooth TM , the two Handheld Terminals should be located within about five meters (19 11 ⁄ 16 " ) from each other, as long as there is nothing blocking the path between...

E-44 Resetting the Handheld Terminal Reset and Full Reset (Memory Initialization) Reset Resetting the Handheld Terminal is the same as restarting a computer. Performing a resetcauses all unsaved inputs and edits to be lost, but data that is already stored in thememory as well as all settings should ...

E-45 If reset finds a memory problem A message like the one shown below appears on the display when the reset operationdiscovers a memory problem. When this message appears, press the R trigger key to continue with the reset operation.Note, however, that reset may not be successful depending on the ...

E-51 Connecting the AC Adaptor and Connecting to Computer Use the AC adaptor sold separately from the Bridge Satellite Cradle/Bridge Basic Cradlefor the power supply of the Bridge Satellite Cradle/Bridge Basic Cradle. Always makesure that the power is being supplied to the Bridge Satellite Cradle by...

E-53 Removing the Fall Protector The Bridge Satellite Cradle and Cradle-type Battery Charger Fall Protector can also beremoved. However, it is recommended not to remove the Fall Protector if there is therisk of the Handheld Terminal being mistakenly tipped over and falling after having beenplaced in...

E-55 Using Wall Mount Unit The following procedure explains how to use the optional wall mount unit (DT-891WH)to configure the Bridge Satellite Cradle/Bridge Basic Cradle for a wall-mountedconfiguration. Important! When mounting on a wall, always make sure to attach the Fall Protector. 1. Remove the...

E-59 Using the Cradle-type Battery Charger The optionally available Cradle-type Battery Charger (HA-A30CHG) lets you charge theHandheld Terminal’s battery simply by placing the Handheld Terminal onto the charger.An optional wall mount unit (DT-891WH) lets you mount the Cradle-type BatteryCharger on ...

E-61 Connecting the AC Adaptor for Cradle-type Battery Charger Use the special AC adaptor (sold separately) for the Cradle-type Battery Charger toconnect to a wall outlet. 1. After making sure that the Cradle-type Battery Charger power switch is turnedoff, plug the AC adaptor into the ACadaptor jack...

E-63 Using the Dual Battery Charger The optionally available Dual Battery Charger (DT-5022CHG) allows for parallelcharging of two rechargeable battery packs. General Guide Top Bottom Front 1 1 4 4 4 4 3 2 3 3 Accessories Connection Bracket2 screws DT-X5_E_P59_69.p65 04.7.14, 6:05 PM 63

E-66 Using the Dual Battery Charger Connecting Multiple Dual Battery Chargers You can connect up to three Dual Battery Chargers. Doing so makes it possible to supplypower to all the Dual Battery Chargers using the AC adaptor. 1. As shown in the illustrations below, remove the connector covers of the...

E-68 Using Rechargeable Battery Pack Your Handheld Terminal supports use of two battery pack types of different capacity. Youcan select the one that best suits your needs in terms of operating time, the type ofoptions you need to use, etc.When using the large-capacity battery pack, you need to use t...

7 日 本 語 電源の取り付け方と接続 電源は別売の専用カープラグコード（DT-827CAC）を使用してください。 1 本体の電源スイッチがOFFであることを 確認してから背面のACアダプタジャッ クにカープラグコードを差し込みます。 2 カープラグコードのプラグをD C   1 2 / 24Vの車のシガレットライターソケット に差し込みます。 3 電源スイッチをONにします。本機の電 源表示用LEDが、赤色に点灯します。 4 ハンディターミナル底面の給電端子と本 機の給電端子を合わせ、カチッと音がす るまで押し込みます。本機の電源表示用 LEDが、緑色に点灯します。 充電が完了すると、ハンデ...

8 使用上のご注意 •  給電端子は絶対にショートさせないでください。ショートさせると故障の原因 となります。 • HA-A34AT及びDT-827CACのご利用にあたり、当社では取り付けにかかわるご相談、実務等行うことはできません。本製品の取り付け方法、取り付け強度、取り付け作業につきましては専門の取り付け業者もしくはお客様にて充分なご検討ご検証いただいた上、ご運用いただけますようお願い申し上げます。 カーバッテリーを使用時のご注意 • 配線を抜き差しする際は、本機の電源スイッチをOFFにして行ってください。 • エンジンを始動する場合は、本機の電源スイッチをOFFにして行ってください。 •...

9 ENGLISH A diagonal line indicates some- thing you should not do. The symbolshown here indicates you should nottry to take the unit apart. ●  A black circle indicates some- thing you should do. The symbolshown here indicates you should un-plug the unit from the wall outlet. Avoiding Traffic Acciden...

10 This symbol indicates information that, if ignored or applied incor-rectly, creates the possibility of death or serious personal injury. Water and Foreign Matter • Never let water get into the Battery Charger Car Mount Unit and take care to keepit from getting wet. Moisture creates the risk of fi...

11 ENGLISH This Battery Charger Car Mount Unit (HA-A34AT) is used by intercharging with the upper part of the Cradle-Type Battery Charger (HA-A30CHG). After installing this Battery Charger Car Mount Unit, it can be used to charge the battery installed in the Handheld Terminal using power from the ci...

12 1 While placing the Cradle-Type Battery Charger on its side as shown in the illustration, grab onto the circled portion and apply force in the direction of the arrow to remove, and then affix the seal included with the Cradle-Type Battery Charger to the location where the Fall Protector is instal...

13 ENGLISH Connecting the Car Power Cable Use the dedicated Car Power Cable (DT-827CAC) sold separately for connecting the Car Mounted Battery Charger (HA-A30CHG with HA-A34AT installed) to the cigarette lighter in your car. 1 After first checking to make sure the power of the Handheld Terminal is O...

14 Important! • Take care to avoid allowing the power contacts to become connected to each other,which creates a short. • Regarding the installation of HA-A34AT and DT-827CAC in your car, no technicaladvice is available from CASIO. Consult with automotive parts store or specializedstore regarding th...

15 中　文 斜线表明不应做的事情 。 此处所 示的符号表明，不应拆开本设备 。 ● 黑圈表明应该做的事情 。 此处所示 的符号表明，应从墙壁的插座上拔下本设备的电源线 。 标记和符号 安全防护措施 恭贺阁下选购本卡西欧产品 。 在初次使用本产品前，请务必阅读以下安全防护措施 。 请妥善 保存本说明书以备今后查阅 。 避免交通事故 • 切勿在操作汽车时使用车用蓄电池充电器配件 。 应在进行任何操作前将汽车停 于安全的地方 。 • 切勿将车用蓄电池充电器配件置于可能会干扰汽车正常操作的地方，如阻碍驾驶员前后视线，转向，或变速杆、刹车踏板或其他汽车控制部件的正常操作，或任何可能危及乘客安全的地方 ...

16 该符号表明，如果忽略或使用不当，有可能造成死亡或严重的人身伤害 。 水和异物 • 切勿使水进入车用蓄电池充电器配件并小心防止充电器受潮 。 湿气可能会造成 火灾和触电的危险 。 • 如有异物或湿气进入车用蓄电池充电器配件，应立即将汽车电源电缆 (DT-827CAC) 的插头从汽车的点烟器插座上拔出并断开车用蓄电池充电器配件 。 请 与原始经销商或经授权的卡西欧服务供应商联系以寻求帮助 。 继续使用车用蓄 电池充电器配件会造成火灾和触电的危险 。 离开汽车 • 无论何时离开汽车，应务必将汽车电源电缆 (DT-827CAC) 的插头从点烟器插座上拔下 。 将车用蓄电池充电器配件留在插座上会耗...

17 中　文 通过与座式蓄电池充电器 (HA-B30CHG) 的上部交互充电的方式使用该车用蓄电池充电器配件 (HA-B34AT) 。 在安装该车用蓄电池充电器配件后，可使用车内点烟器的电源给装于手持 打印机终端中的电池进行充电 。 检查内容 车用蓄电池充电器配件 托架螺钉 (4) 托架（安装托架） HA-B34AT̲P15-23 4/14/04, 10:08 PM Page 17 Adobe PageMaker 6.5J/PPC

18 1 按图示拆下螺钉，将座式蓄电池充电器的上部拆下 。 2 按图示用随附的螺钉安装车用蓄电池充电器配件 。 3 根据需要按图示安装托架 。 安装车用蓄电池充电器配件 3 2 1 1 2 1 3 左孔 右孔 HA-B34AT̲P15-23 4/14/04, 10:08 PM Page 18 Adobe PageMaker 6.5J/PPC

19 中　文 连接汽车电源电缆 用单独出售的指定的汽车电源电缆 (DT-827CAC) 将车用蓄电池充电器（装有HA-B34AT的HA-B30CHG）连接到汽车的点烟器上 。 1 首先检查并确认手持打印机终端的电源已经关闭 (OFF)，将汽车电源电缆插入车用蓄电池充电器背面的AC适配器的插孔 。 2 将汽车电源电缆插入使用12/24V DC电源汽车的点烟器插座中 。 3 打开电源 。 车用蓄电池充电器上的电源指 示灯点亮，显示红色 。 4 使手持打印机终端底部上的电源接触器与车用蓄电池充电器的电源接触器接触，然后将手持打印机终端置于车用蓄电池充电器 上 ， 直 至 听 到 “ 咔 嗒 ” 的 ...

21 MEMO HA-B34AT̲P15-23.p65 04.4.5, 11:52 AM Page 21 Adobe PageMaker 6.5J/PPC