Casio EX-292- Manuals

Casio EX-292– User Manual in PDF format online.

Manuals:

User Manual

User Manual Casio EX-292

Summary

Page 2 - CONTENTS

CONTENTS SPECIFICATIONS ....................................................................................................................................... 1 BLOCK DIAGRAM ...............................................................................................................................

Page 3 - SPECIFICATIONS

— 1 — SPECIFICATIONS Image Files Format Snapshots: JPEG (Exif Ver.2.2); DCF (Design Rule for Camera File system) 1.0 standard; DPOF compliant Movies: Motion JPEG AVI format Audio: WAV Recording Media Built-in Memory 8.0 MB SD Memory Card MultiMediaCard Approximate Memory Capacity and File sizes • Sn...

Page 5 - Power Supply

— 3 — • Battery: NP-40 (Rated Capacity: 1300 mAh) • Recording Medium: SD memory card • Measurement Conditions *1 Number of Shots (CIPA) In accordance with CIPA standards Normal temperature (23 ° C (73 ° F)), monitor on, zoom operation between full wide and full telephoto every 30 seconds, during whi...

Page 7 - BLOCK DIAGRAM

— 5 — BLOCK DIAGRAM + – Lens Unit PENT AX 3X Motor FPC Connector 23PIN MO T OR-dr LV8054LP LCD/BL UNIT 2.8" WIDE LCD 7-LED BL KEY -FPC Connector 45PIN Connector 14PIN CCD MN39850P A J3L 1/1.8" 10M Connector 33PIN CDS+Vdr AD9927BBCZRL LSI-SiP R8J30225EBGV SD Card Connector SD- BU S A U DIO IC...

Page 8 - TEST MODE; the data inside, which will make the camera unusable.

— 6 — TEST MODE Note: Never perform the menu items unless otherwise instructed. Doing so may cause destruction of the data inside, which will make the camera unusable. ■ To boot the test mode 1. While firmly pressing down both [BS] and [UPPER], turn the power on. 1 : V E R S I O N I N F O2 : U S B T...

Page 9 - PROGRAM VERSION UPGRADING

— 7 — PROGRAM VERSION UPGRADING 1. To update the firmware version 1. Prepare the memory card which contains the firmware for EX-Z1000 in the root directory. EX-Z1000.bin 2. Insert the above memory card into the camera, and set a fully charged battery in the camera. 3. Press the [power button] while ...

Page 12 - ADJ TOOL; Introduction

— 10 — ADJ TOOL ■ Introduction Make sure to perform the adjustment by the USB ADJ Tool “adj03SSAW.exe” when replacing the lens unitor the PCB.Here the necessary software, driver and setting are explained to use “adj03SSAW.exe”.Note that the tool, drivers etc. are available only for Windows. 1. Prepa...

Page 16 - VCOM DC ADJUSTMENT; Purpose; The three tools can be obtained from the following global site.

— 14 — VCOM DC ADJUSTMENT ■ Purpose Readjust the VCOM value to minimize the flicker of the LCD after replacing the LCD or the main PCB. ■ Necessary tools 1. Camera (Charge its battery fully)2. Photo diode (S2281-01) : See Fig 1.3. Photo sensor amp (C2719) : See Fig 2.4. BNC-BNC cable (E2573) x 2 : S...

Page 17 - Procedure; a) Tu r n t h e p o w e r o n w h i l e p r e s s i n g “ B S ” a n d “ U P P E R ” .

— 15 — ■ Procedure 1. Camera setting a) Tu r n t h e p o w e r o n w h i l e p r e s s i n g “ B S ” a n d “ U P P E R ” . After pressing “DOWN” key twice, press “DISP” and “MENU”.Select "2:USB TCC TEST", and press "SET" button.Select "1:USB TCC ON", and press "RIGHT"...

Page 19 - PROCEDURE; e) Press SET button and System is initialized.; CURRENT CONSUMPTION; A when power is turned OFF.

— 17 — THE COUNTERMEASURE FOR "SYSTEM ERROR" System error may occur when the battery is removed while data is written to the internal memory. ■ PROCEDURE 1. Initialize the system. a) Enter the TEST mode.b) Select "3:ROM UPDATE" and press SET button.c) Next, select "5:SYSTEM INITI...

Page 20 - RESETTING THE PLACE OF DESTINATION

— 18 — RESETTING THE PLACE OF DESTINATION When the main PCB is replaced, the setting of the destination will be changed, therefore resetting is required.However, when the firmware is changed or fixed, the setting of the destination will be held, therefore resettingis not required.Use the destination...

Page 21 - DISASSEMBLY; * Make sure to use correct screws when assembling since

— 19 — DISASSEMBLY * Make sure to use correct screws when assembling since there are several kinds of them. It is a good idea to sort them as shown in the right when disassembling. 1. Remove the battery. ■ Remove the case 2. Remove six screws. Screw (S3) Screw (S3) Screw (S2) Screw (S3) Screw (S1) S...

Page 28 - ASSEMBLY; Assembling the lens unit

— 26 — ASSEMBLY ■ Assembling the lens unit 1. Set the lens unit and fix it with three hooks. <hook locations> ■ Assembling the speaker 2. Set the lens unit and fix it with three hooks. * Pay attention to the lead wire positions.

Page 35 - Power button

— 33 — 19.Set the center case (B). 20.Set the strap. 21. Set the rear case. 22. Fix it with five screws. * Do not nip the lead wires. 23. Set the power button. 24. Set the center case (A). 25. Fix it with one screw. Power button Center case (A) Screw (S1) Screw (S2) Screw (S3) Screw (S3) Screw (S3) ...

Page 36 - EXPLODED VIEW

— 34 — EXPLODED VIEW 4 8 7 7 9 6 5 10 11 16 18 20 19 21 17 15 12 13 14 S1 S2 S1 S2 S3 S2 S3 S1 S3 S3 S4 S5 S1 24 22 26 25 2 1 2 3 27 31 28 29 30 23 32 23 S3

Page 37 - PARTS LIST

— 35 — PARTS LIST N Item Parts Code Parts Name Specification QTY Price Code R Remark N 1 10242103 BOX ASSY/BATTERY RJK509022*001V02 1 C N 2 10241458 TAPE/LCD RJK508890-006V01 2 X 3 10219347 SPRING/BATTERY RJK507851-001V02 1 C N 4 10241438 CASE/CENTER/A RJK509023-001V01 1 C N 5 10241439 CASE/CENTER/B...

Page 39 - PRINTED CIRCUIT BOARD

— 37 — PRINTED CIRCUIT BOARD MAIN PCB (TOP VIEW) FU101 FU100

Page 41 - SCHEMATIC DIAGRAMS

— 39 — SCHEMATIC DIAGRAMS MAIN PCB (1/3) 2 2 5 PSIN KINTB VBUS FOUT WATCH PSCK RESETB PSRDY ADPIN BATTEMP PSRSTB PSOUT SHUTTER2 MONOOUT KIN4 VA_STBY POWSW VIDEO VOUT VOUT DPLUS DMINUS SDCLK CHGCTL KIN4 BATTEMP PWCTL0 KIN2 KIN1 KIN3 USB-LED SDCD SDWP SDDAT3 SDDAT2 SDDAT1 SDDAT0 SDCLK SDCMD DPLUS DMIN...

Page 44 - Overseas Service Division

CASIO COMPUTER CO.,LTD. Overseas Service Division 6-2, Hon-machi 1-Chome Shibuya-ku, Tokyo 151-8543, Japan