Casio C6800IA48FPD - Manuals

C H A P T E R 1 Product Overview The family of switches are Ethernet switches to which you can connect devices such as Cisco IP Phones,Cisco Wireless Access Points, workstations, and other network devices such as servers, routers, and otherswitches. Some models of the switches support stacking throu...

For switches with a 740 W power budget, you can budget the PoE and PoE+: • 15.4 W of PoE output on 48 ports • 30 W of PoE+ on 24 ports On a per-port basis, you control whether or not a port automatically provides power when an IP phone or anaccess point is connected. The PoE ports use RJ-45 connecto...

This illustration shows a 5-pin mini-Type B USB port. Figure 2: USB Mini-Type B Port With the Cisco Windows USB device driver, you can connect and disconnect the USB cable from the consoleport without affecting Windows HyperTerminal operations. The console output always goes to both the RJ-45 and th...

2 RPS = redundant power system — only on switch models that support RPS. 3 only on switch models that support PoE. System LED Table 2: System LED System Status Color System is not powered on. Off System is operating normally. Green POST in progress. Blinking green System is receiving power but is no...

Table 4: Master LED Description Port Mode Switch is not the stack master. Off Switch is the stack master or a standalone switch. Green An error occurred when the stack was electing the stack master switch, or another type ofstack error occurred. Amber Port LEDs and Modes The port and module slots ea...

Meaning Port LED Color Port Mode 10/100/1000 ports SPEED Port is operating at 10 Mb/s. Off Port is operating at 100 Mb/s. Green Port is operating at 1000 Mb/s. Blinking green SFP+ module ports Port is not operating. Off Port is operating at 10 Gb/s. Blinking green Port is operating at 1 Gb/s. Green ...

This figure shows the LEDs on the first switch, which is stack member number 1. Figure 4: STACK LED Stack member 3 3 Stack member 1 1 Stack member 2 2 When you select the STACK LED, the respective STACK LEDs are green when the stack ports (on the switchrear panel) are up, and the respective Stack LE...

Description Color LED USB console port is active. When this LED is on, the RJ-45 console port LED is off. Green USB console port The port is not active, and the RJ-45 console port is active. Off Ethernet Management Port LED Table 8: Ethernet Management Port LED Description Color Active link to PC. G...

RPS Connector 3 FlexStack-Plus ports 1 AC power connector 4 Fan Exhaust 2 FlexStack-Plus Ports and LEDs The Catalyst 6800IA switches support stacking with the FlexStack-Plus ports on the switch rear panel and a0.5-meter FlexStack cable. Figure 6: FlexStack-Plus Ports LED for Stack port 2 2 LED for S...

RPS Connector The Cisco RPS 2300 (model PWR-RPS2300) supports the Catalyst 6800IA switch. Attach only the following Cisco RPS model to the RPS receptacle: RPS2300. Statement 370 Warning Connect the switch and the redundant power system to different AC power sources. Use this cable for the RPS: CAB-R...

C H A P T E R 2 Switch Installation • Safety Warnings, page 15 • Tools and Equipment, page 18 • Installation Guidelines, page 18 • Verifying Switch Operation, page 19 • Planning and Installing a Switch Stack (Optional), page 20 • Installing the Switch, page 23 • Connecting the FlexStack Cables (Opti...

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnectionsare made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using suchinterconnection methods, unless the exposed metal parts are located within a restricted access location...

• Temperature around the unit does not exceed 113°F (45°C). If the switch is installed in a closed ormultirack assembly, the temperature around it might be greater than normal room temperature. • Humidity around the switch does not exceed 95 percent. • Altitude at the installation site is not greate...

Planning and Installing a Switch Stack (Optional) Stack Guidelines • Order the appropriate cable from your Cisco sales representative. The length of FlexStack cable dependson your configuration. These are the different sizes available: ◦ CAB-STK-E-0.5M= (0.5-meter cable) ◦ CAB-STK-E-1M= (1-meter cab...

Stack Cabling These figures show the switches stacked in a vertical rack or on a table. The connections are redundant. Figure 7: Stacking Switches with the 0.5-meter FlexStack Cable Figure 8: Stacking Switches with 0.5-meter and 3-meter FlexStack Cables Catalyst 6800IA Switch Hardware Installation G...

Stack Bandwidth and Partitioning Examples This figure shows a stack that provides full bandwidth with redundant connections. Figure 9: Stack with Full Bandwidth Connections This figure shows a stack with incomplete stack cabling connections. This stack provides only half bandwidthand does not have r...

This figure shows a stack with a bad link B. This stack partitions into two stacks, and switch 1 and switch 3are stack masters. Figure 12: Partitioned Stack with a Failover Condition Power-On Sequence for Switch Stacks Consider these guidelines before you power on the switches in a stack: • The sequ...

Attaching the Rack-Mount Brackets Procedure Use two Phillips flat-head screws to attach the long side of the bracket to each side of the switch. Figure 14: Attaching Brackets for 19-inch Racks Mid-mounting position 3 Front-mounting position 1 Rear-mounting position 4 Number-8 Phillips flat-head scre...

Mounting in a Rack Procedure Step 1 Use the four supplied Phillips machine screws to attach the brackets to the rack. Step 2 Use the black Phillips machine screw to attach the cable guide to the left or right bracket. Number-12 Phillips pan-head screws(48-0523-01) or Number-10 Phillips pan-headscrew...

Rear-mounting position 6 Front-mounting position 3 Wall-Mounting Read the wall-mounting instructions carefully before beginning installation. Failure to use the correcthardware or to follow the correct procedures could result in a hazardous situation to people and damageto the system. Statement 378 ...

Attaching the RPS Connector Cover If an RPS is not connected to the switch, install an RPS connector cover on the back of the switch. Statement265 Warning Procedure If you are not using an RPS with your switch, use the two Phillips pan-head screws to attach the RPS connectorcover to the back of the ...

Installing the Switch on a Table or Shelf Procedure Step 1 To install the switch on a table or shelf, locate the adhesive strip with the rubber feet in the mounting-kitenvelope. Step 2 Attach the four rubber feet to the four circular etches on the bottom of the chassis. Step 3 Place the switch on th...

When you connect the FlexStack cable to the STACK 1 port, the tab should be above the connector.When you connect the FlexStack cable to the STACK 2 port, the tab should be below the connector. Note Step 3 Replace the dust covers when you remove the FlexStack cables from the connectors. Removing and ...

Step 6 Secure the AC power cord by pressing on the retainer. Figure 22: Securing the Power Cord in the Retainer Installing SFP and SFP+ Modules The SFP+ slots support both SFP and SFP+ modules. See the switch release notes on Cisco.com for the list of supported SFP modules. Use only Cisco SFP module...

Removing an SFP or SFP+ Module Procedure Step 1 Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface. Step 2 Disconnect the cable from the SFP module. For reattachment, note which cable connector plug is send (TX)and which is receive (RX). Step 3 Insert a dust plug into the...

Procedure Step 1 Remove the rubber plugs from the module port and fiber-optic cable, and store them for future use. Step 2 Insert one end of the fiber-optic cable into the SFP or SFP+ module port. Step 3 Insert the other cable end into a fiber-optic receptacle on a target device. Figure 24: Connecti...

10/100/1000 Port Connections The switch 10/100/1000 port configuration changes to operate at the speed of the attached device. If theattached ports do not support autonegotiation, you can manually set the speed and duplex parameters.Connecting devices that do not autonegotiate or that have the speed...

C H A P T E R 3 Troubleshooting This chapter contains these topics: • Diagnosing Problems, page 41 • Finding the Serial Number, page 45 Diagnosing Problems The LEDs on the front panel provide troubleshooting information about the switch. They show POST failures,port-connectivity problems, and overal...

10/100/1000 PoE+ Port Connections A powered device connected to PoE port does not receive power: • Use the Mode button to show the PoE status for all ports. • Use the show interfaces privileged EXEC command to see if the port is in error-disabled, disabled, or shutdown. Reenable the port if necessar...

Ping End Device Ping from the directly connected switch first, and then work your way back port by port, interface by interface,trunk by trunk, until you find the source of the connectivity issue. Make sure that each switch can identifythe end device MAC address in its Content-Addressable Memory (CA...

Cabling Distance If the port statistics show excessive FCS, late-collision, or alignment errors, verify that the cable distancefrom the switch to the connected device meets the recommended guidelines. Finding the Serial Number If you contact Cisco Technical Assistance, you need to know the switch se...

A P P E N D I X A Technical Specifications This appendix contains these topics: • Environmental Specifications, page 47 • Specifications for the Catalyst 6800IA Switches, page 47 Environmental Specifications This table describes the environmental specifications. Table 12: Environmental Specification...

A P P E N D I X B Connector and Cable Specifications This appendix contains these topics: • Connector Specifications, page 49 • Cables and Adapters, page 50 Connector Specifications 10/100/1000 Ports (Including PoE) All 10/100/1000 ports use standard RJ-45 connectors and Ethernet pinouts. Figure 27:...

SFP Module Connectors Figure 28: Duplex LC Cable Connector Figure 29: Simplex LC Cable Connector Figure 30: Copper SFP Module RJ-45 Connector Cables and Adapters SFP Module Cables For cabling specifications, refer to the Cisco SFP and SFP+ Transceiver Module Installation Notes . Catalyst 6800IA Swit...

Cable Pinouts Figure 31: Four Twisted-Pair Straight-Through Cable Schematic Figure 32: Four Twisted-Pair Crossover Cable Schematic Figure 33: Two Twisted-Pair Straight-Through Cable Schematic Figure 34: Two Twisted-Pair Crossover Cable Schematic Catalyst 6800IA Switch Hardware Installation Guide 52 ...

Figure 35: Identifying a Crossover Cable Console Port Adapter Pinouts The RS-232 console port uses an 8-pin RJ-45 connector. Use an RJ-45-to-DB-9 adapter cable to connect theswitch console port to a console PC. You need to provide a RJ-45-to-DB-25 female DTE adapter to connectthe switch console port...