Casablanca PN C3543001 AT0309 - Manuals

Page 2 - isotope

2 RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! Please take a moment to locate the model number and serial number from your fan (see below) and record this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already. These numbers are fou...

Page 3 - Parts guide

3 Parts guide item # description Picture (not to scale) Quantity 1. Motor Housing 1 2. Ceiling Mounting Plate 1 3. Phillips Screwdriver 1 4. Screw Pack (a): 1 1 / 2 " x 8-32" Roundhead screws and Washers 2 ea 5. Screw Pack (a): 1 1 / 2 " Wood Screws and Washers 2 ea 6. Screw Pack (a): 3&...

Page 4 - SafE USE; unpacking

4 C ircuit Breaker (trip breaker for the circuit you will be working on) Fuse Box (Remove fuse for the circuit you will be working on) 18" 84" 70" SafE USE INTrOdUCTION BEfOrE YOU STarT from bottom edge of blade to floor from wall to end of blade dimensions indicated are the minimum allo...

Page 5 - sotope; MOUNTING RECOMMENDATIONS; Location; GENERAl GUIDElINES; To reduce the risk of fire, electrical shock,

5 I sotope ® MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in y...

Page 6 - faN INSTallaTION; CEIlINg MOUNTINg PlaTE INSTallaTION; only the mounting hardware provided

6 faN INSTallaTION CeiLinG haRdWaRe (not to scale) CEIlINg MOUNTINg PlaTE INSTallaTION Ceiling Mounting Plate Caution: to reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting plate. note: After removing the old fixt...

Page 7 - MOTOR hOUSING INSTAllATION; use the hanging hole on the body of the fan

7 I sotope ® MOTOR hOUSING INSTAllATION hanGinG hoLe hanGinG hoLe hooK CeiLinG MountinG PLate (Figure #2) (Figure #3) Step 2b. use the hanging hole on the body of the fan to hang the fan on the hook of the ceiling mounting plate. This will help you in making the electrical connections as shown in Fi...

Page 11 - BladE INSTallaTION; by hand only

11 I sotope ® BladE INSTallaTION BlADE hARDwARE (not to scale) Blades (5) Blade Screws and Washers (16) Blade installationStep 3a. locate the Casablanca logo on the end of the blade as shown in Figure #1. Slide the end of the blade with the three holes into the slot located on the blade ring. (Make ...

Page 12 - lIghT BUlB aNd glaSS INSTallaTION; install halogen Bulbs

12 lIghT BUlB aNd glaSS INSTallaTION install halogen Bulbs Step 4. Screw the two bulbs into the light fixture as shown in Figure #1. note: When replacing the bulbs, be sure to use only 50-watt maximum. haRdWaRe (not to scale) Glass Shade 50 -watt halogen Bulbs (2) iMPoRtant! When installing a haloge...

Page 13 - RIME•; Standard toggle Light Switch

13 PrIME •TOUCH ® W-505 CONTrOl INSTallaTION CONTrOl BraCKET INSTallaTION haRdWaRe (not to scale) P RIME• T OUCH ® SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. CAUTION! Do not use with wall dimmer. Standard toggle Light Switc...

Page 14 - rEMOTE OPEraTION; breaker, then back on, for a previously

14 P RIME• T OUCH ® rEMOTE OPEraTION Send Signal lED ChaNgINg TraNSMITTEr frEqUENCY SETTINg You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately.Step 1. at the circuit breaker or fuse box, turn the ...

Page 15 - TROUBlEShOOTING TIPS

15 I sotope ® Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBlEShOOTING TIPS PRoBLeM PoSSiBLe ReMedieS Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make ...

Page 16 - CARE RECOMMENDATIONS; Isotope®

16 Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.• A vacuum cleaner brush nozzle can remove heavier dust.• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth....