Casablanca C35G45L - Manuals

Casablanca C35G45L – Manual in PDF format online.

Manuals:

Manual

Manual Casablanca C35G45L

Summary

Page 2 - isotope

2 RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! Please take a moment to locate the model number and serial number from your fan (see below) and record this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already . These numbers are fo...

Page 3 - Parts Guide

3 Parts Guide Item # Description Picture (not to scale) Quantity 1. Motor Housing 1 2. Ceiling Mounting Plate 1 3. Phillips Screwdriver 1 4. 1" x 8-32 Roundhead screws and Washers 2 EA 5. 1 1 / 2 " Wood Screws and Washers 2 EA 6. 3" Wood Screws and Washers 2 EA 7. Fan Mounting Screws 4 8...

Page 4 - SafE USE; unpacking

4 C ircuit Breaker (trip breaker for the circuit you will be working on) Fuse Box (Remove fuse for the circuit you will be working on) 18" 84" 70" SafE USE INTrOdUCTION BEfOrE YOU STarT from bottom edge of blade to floor from wall to end of blade Dimensions indicated are the minimum allo...

Page 5 - sotope; MOUNTING RECOMMENDATIONS; Location; GENERAl GUIDElINES; or personal injury, mount to outlet box

5 I sotope ® MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in y...

Page 6 - faN INSTallaTION; CEIlINg MOUNTINg PlaTE INSTallaTION; only the mounting hardware provided

6 faN INSTallaTION CeiLinG haRdWaRe (not to scale) CEIlINg MOUNTINg PlaTE INSTallaTION Ceiling Mounting Plate Caution: to reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting plate. note: After removing the old fixt...

Page 7 - MOTOR hOUSING INSTAllATION

7 I sotope ® MOTOR hOUSING INSTAllATION hanGinG hoLe hanGinG hoLe hooK CeiLinG MountinG PLate (Figure #3) (Figure #4) Step 2d. Use the hanging hole on the body of the fan to hang the fan on the hook of the ceiling mounting plate. This will help you in making the electrical connections as shown in Fi...

Page 11 - BladE INSTallaTION; by hand only

11 I sotope ® BladE INSTallaTION BlADE hARDwARE (not to scale) Blades (5) Blade Screws and Washers (16) Blade installationStep 3a. Slide the end of the blade with the three holes into the slot located on the blade ring. (The blades will only fit properly over the screws holes one way. If the holes d...

Page 12 - lIghT BUlB aNd glaSS INSTallaTION; install halogen Bulbs

12 lIghT BUlB aNd glaSS INSTallaTION install halogen Bulbs Step 4. Screw the two bulbs into the light fixture as shown in Figure #1. note: When replacing the bulbs, be sure to use only 50-watt maximum. haRdWaRe (not to scale) Glass Shade 50 -watt halogen Bulbs (2) iMPoRtant! When installing a haloge...

Page 13 - Wall Control; Wall Plate; W-74 Wall control PreParation; Cover Plate; installing the W-74 Wall control; W-74 ContRoL inStaLLation; single W-74 installation; Figure 1

direct - touch 13 13 W-74 Wall Control W-74 Wall control PreParation Wall Plate Screws (2) Switch Mounting Screws (2) (4) Wire Cap Warning! To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation or repair ...

Page 14 - Dual W-74 installation; NEUTRAL; Figure 3; Figure 2

14 1. To control the fan and lights from two locations (a three-way circuit), use two W-74 wall controls. 2. remove the screws and switch plate from the existing switch box and the screws holding the switch in the switch box. Figure #5 3. Pull the existing switch from the switch box to expose the...

Page 15 - oPeration PoWer; To select the desired fan speed:; oPeration reversing airfloW; Note: It is normal for the fan to start; Figure 5

direct - touch 15 W-74Wall Control BLaCK anD WHiTESTriPED WirE 2 Red WiReS 2 BLaCKWirES 6. remove the two remaining wires from the three-way switch. Connect one black wire of these wires to the black wire on the W-74 control. Secure the splice with a wire nut. 7. The remaining wire is to be connec...

Page 16 - changing frequency setting; NOTE: DO NOT set dip switch setting in the remote; oPeration cfl MoDe; oPeration lights

16 changing frequency setting You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. diP SWitCheS Set to ‘111111’ (Factory Setting) NOTE: DO NOT set dip switch setting in the remote to ‘000000’, this...

Page 17 - autoMatic DeMonstration PrograM

direct - touch 17 To change frequency: 1. Turn power OFF at the circuit breaker or fuse box and at the toggle switch, for the fan you want to change. 2. remove the screws and switch plate from the existing switch box. 3. remove the screws holding the switch in the switch box. 4. Pull the existin...

Page 18 - Note: This program overrides all manual control of lights and fan .; light-MinDer® PrograM

18 18 oPeration hoMe-safe® PrograM oPeration fan-MinDer™ PrograM To operate the Home-Safe Program : 1. Turn the power button off for at least 5 seconds. 2. Turn the on. immediately press and hold the "3" button for 5 seconds. a series of tones will be heard indicating the command has been ...

Page 19 - TROUBlEShOOTING TIpS

19 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBlEShOOTING TIpS This device complies with rSS-210 of industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this ...

Page 20 - CARE RECOMMENDATIONS; Isotope®

20 Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.• A vacuum cleaner brush nozzle can remove heavier dust.• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth....