Casablanca C25G624FPOMONA - Manuals

Page 7 - Structural Support; Mounting Guidelines; Location

Twain ™ 7 Structural Support Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Using Existing Ceiling Fixture Outlet Box After turning the power O...

Page 8 - Sloped Ceiling Installations

Twain ™ 8 Sloped Ceiling Installations When to Use an Extension Downrod For optimum performance and appearance, use an extension downrod with your Casablanca fan when installing on high (cathedral) ceilings or sloped ceilings. Casablanca offers accessory downrods in increments of 6" up to 5’. Se...

Page 9 - Assembling; Attaching the Crossbar Mounting Bracket; Installing the Mounting Hardware

Twain ™ 9 Assembling 1 Determine the need for a lag screw based on the Mounting Guidelines previously described. If in doubt whether you need to install the lag screw, consult a qualified electrician. 2 If a lag screw is required, remove the plug in the center of the ceiling fixture outlet box. If t...

Page 10 - Attaching the Canopy

Twain ™ 10 4 To install the lag screw (if needed), slide the remaining washer onto the lag screw. Pass the lag screw through the center hole in the crossbar mounting bracket. Secure the lag screw into the guide hole, tightening until the ceiling fixture outlet box is firmly mounted to the support be...

Page 11 - Installing the Fan

Twain ™ 11 Assembling 1 Remove the paper shield from the motor. 2 Examine the interior of the motor coupling. If the end of the set screw is inside the motor coupling space, use the Allen wrench to loosen the screw. Installing the Fan Hardware (not to scale) Perma•Lock™ Downrod and Ball Assembly (1)...

Page 13 - Hanging the Fan

Twain ™ 13 STEPS 9-10 RED and BLUE wires 2 BLACK wires 2 WHITE wires 3 GREEN wires Wire nut Hanging the Fan 8 Hold the motor housing with both hands. Insert the ball of the downrod into the canopy opening. Check to ensure that the wires are not pinched. Rotate the motor housing until the slot in the...

Page 16 - Operating the W-81 Wall Control

Twain ™ 16 5 Fasten one of the two wall plates (white or ivory) to the wall control using the two wall plate screws. 6 Set the fan speed to HIGH on the wall control. Return power to the panel and test the controller. CAUTION: Ñ Failure to set the fan speed to HIGH can result in faulty operation of t...

Page 17 - Attaching

Twain ™ 17 STEP 1 STEP 2 Blade iron Blade holder ring Blade holder screws (2) Installed blades Fan blade assembly Installing the Blades Hardware (not to scale) Blades (5) Blade Iron Plate Screws (21) Blade Iron Plates (5) Blade Irons (5) Blade Iron Screws (11) Assembling 1 Place the blade iron plate...

Page 18 - Attaching the Light Fixture

Twain ™ 18 Installing the Light Fixture Hardware (not to scale) Light Adapter Plate (1) Light Adapter Screws (3) Light Fixture Screws (4) Halogen Downlight Bulbs, 50W (2) Glass Shade (1) Finial (1) Light Fixture (1) STEPS 2-3 Light adapter plate Light adapter screws (3) Attaching the Light Fixture 1...

Page 19 - Attaching the Halogen Bulbs

Twain ™ 19 STEP 6 Halogen bulbs (2) 5 Align the light fixture to the four posts on the light adapter plate using the light fixture screws. Attaching the Halogen Bulbs NOTE: Do not remove the protective sleeve on the halogen bulb. Touching the glass casing of the bulb may damage or break the glass. 6...

Page 20 - Attaching the Glass Shade

Twain ™ 20 Attaching the Glass Shade 7 Insert the threaded rod from the light assembly through the hole in the center of the glass shade. 8 Thread both pieces of the finial onto the threaded rod. Screw the finial into place securely. STEP 7 Glass Shade Finial Threaded rod STEP 8 Installed fan and li...

Page 21 - Problems and Possible Remedies; Care Recommendations

Twain ™ 21 Troubleshooting Tips Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. Problems and Possible Remedies Fan will not start Check the main circuit fuses, circuit breakers, and wall • control position. Check all wire connections. Ma...