Casablanca #C18G500FPOMONA - Manuals

Page 7 - Structural Support; Mounting Guidelines; Location

Atria ™ 7 Structural Support Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Using Existing Ceiling Fixture Outlet Box After turning the power O...

Page 8 - Sloped Ceiling Installations

Atria ™ 8 Sloped Ceiling Installations When to Use an Extension Downrod For optimum performance and appearance, use an extension downrod with your Casablanca fan when installing on high (cathedral) ceilings or sloped ceilings. Casablanca offers accessory downrods in increments of 6" up to 5’. Se...

Page 9 - Assembling; Attaching the Crossbar Mounting Bracket; Installing the Mounting Hardware

Atria ™ 9 Assembling 1 Prepare the ceiling fixture outlet box for the lag screw by removing the plug in the center. If the outlet box does not have a plug, drill a ½-inch hole in the center of the box. After drilling a hole in the outlet box, drill a ¼-inch hole 3 inches deep into the joist used to ...

Page 10 - Attaching the Canopy

Atria ™ 10 Attaching the Canopy 4 To install the canopy hardware, set aside the canopy hatch and one canopy hatch screw and lock washer. You will install the canopy hatch in the next section. Attach the canopy to the crossbar mounting bracket with three of the canopy screws and lock washers. Using t...

Page 11 - Installing the Fan

Atria ™ 11 Assembling 1 Remove the paper shield from the motor. 2 Examine the interior of the motor coupling. If the end of the set screw extends inside the motor coupling space, use the Allen wrench to loosen the screw. Installing the Fan Hardware (not to scale) Perma•Lock™ Downrod and Ball Assembl...

Page 13 - Hanging the Fan

Atria ™ 13 STEPS 8-9 RED and BLUE wires 2 BLACK wires 2 WHITE wires 3 GREEN wires Wire nut Hanging the Fan 7 Hold the motor housing with both hands. Insert the ball of the downrod into the canopy opening. Check to ensure that the wires are not pinched. Rotate the motor housing until the slot in the ...

Page 16 - Operating the W-81 Wall Control

Atria ™ 16 5 Fasten one of the two wall plates (white or ivory) to the wall control using the two wall plate screws. 6 Set the fan pull-chain speed to HIGH and the wall control fan speed knob to HI. Return power to the panel and test the controller. CAUTION: Ñ Failure to set the fan pull- chain spee...

Page 18 - Attaching

Atria ™ 18 Installed blade assemblies 3 Assemble the blade irons, blades, and blade iron plates. Place the blade iron on top of the blade and the blade iron plate underneath the blade. Use a manual screwdriver and the blade iron plate screws to secure the blade assembly. Use four screws per blade. R...

Page 19 - Attaching the Light Fixture

Atria ™ 19 Installing the Light Fixture Hardware (not to scale) Light Fixture (1) Light Fixture Screws (2) Halogen Downlight Bulbs, 50W (2) Glass Shade (1) Light Kit Cap and Finial (1 set) Attaching the Light Fixture 1 Locate and remove the pre-installed wire nuts on the motor housing wires. 2 To at...

Page 20 - Installing the Halogen Bulbs; Attaching the Glass Shade

Atria ™ 20 Installing the Halogen Bulbs NOTE: Do not remove the protective sleeve on the halogen bulbs. Touching the glass casing of a bulb may damage or break the glass. 4 Cut the plastic sleeve on the halogen bulb to expose the connection end of the bulb. Continue to hold the bulb by the sleeve du...

Page 21 - Problems and Possible Remedies; Care Recommendations

Atria ™ 21 Troubleshooting Tips Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. Problems and Possible Remedies Fan will not start Check the main circuit fuses, circuit breakers, and wall • control position. Check all wire connections. Ma...