Casablanca C15G624L - Manuals

5 V eneto ™ Circuit Breaker (Trip breaker for the circuit you will be working on) Fuse Box (Remove fuse for the circuit you will be working on) 18" 70" safe Use • CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and l...

7 V eneto ™ Using Existing Ceiling Fixture Outlet BoxAfter turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for Ceiling Fan Mounting.” If it is not, a ...

9 V eneto ™ Step 6. Twist the Pipe Assembly into the Motor Adapter by turning Counter-Clockwise. Step 7. Securely retighten the setscrew on the Motor Adapter with the Allen Wrench. CAUTION: The Motor Adapter has a special coating on the threads. Do not remove this coating; the coating prevents the d...

10 UPPer gLass Hardware Upper Glass Upper Bulb (6) UPPer gLass asseMBLY Step 1. Slide the Glass over the upper part of the Fan Assembly. Step 2. The Glass should rest inside the rim of the lower part of the motor on top of the foam strips to avoid contact with rim. Step 3. Remove each of the 6 Upper...

11 V eneto ™ Power From Ceiling Line Power (IN) Line Neutral (IN) White Neutral From Ceiling Step 1. Locate the White Line Neutral (IN) and connect it to the White Neutral Wire from your ceiling using one of the supplied orange wire caps. Step 2. Connect the Black Line Power (IN) and the Black Power...

13 V eneto ™ Step 9. Carefully tuck the wires around the Receiver and Hanging Bracket as not to loosen the wire caps. Step 10. Insert 2 Canopy Screws into the Hanging Plate diagonally across from each other so they match the keyholes on the canopy. Canopy Screws Keyhole Slots Step 11. Raise the Cano...

15 V eneto ™ LIgHt kIt Hardware LIgHt kIt InstaLLatIon Lower Glass Light Kit Light Kit Screw (3) Lower Bulb (3) Glass Cover Finial Step 1. To attach the Light KIt Mounting Plate partially install two light kit screws into the switch housing mounting plate. Step 2. Connect the molex plug on the Light...

16 Step 7. Remove the three lower bulbs from their packaging, and install into the light kit. Note: When replaceing bulbs, only replace with max 40 watt bulbs. Step 8. Raise the Glass up to the Glass Adapter on the bottom of the Light Kit. Step 9. Slide the Glass Cover onto the bottom of the glass S...

17 direct - touch 1 2 0 4 3 InstaLLIng tHe w-74 waLL ControL W-74 ContRoL inStaLLation The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching oper...

18 1 2 0 4 3 1. To control the fan and lights from two locations (a three-way circuit), use two W-74 wall controls. 2. Remove the screws and switch plate from the existing switch box and the screws holding the switch in the switch box. Figure #5 3. Pull the existing switch from the switch box to exp...

19 direct - touch 1 2 0 4 3 oPeratIon Power The 1 2 0 4 3 power button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs.The 1 2 0 4 3 power button must be left on to reta...

20 1 2 0 4 3 CHangIng freqUenCY settIng NOTE: All fans leave the factory set to “111111” You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. diP SWitCheS Set to ‘111111’ (Factory Setting) NOTE: DO...

23 V eneto ™ Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. troUBLesHootIng tIPs This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and...

24 ProdUCt sPeCIfICatIons Model name: Veneto Model number: C15g624L dimensions: a = 17.8 B = 25.8 C = 3.4 D = 19.7 E = 7.6 Weight: 47 lbs. Motor: 172 mm x 18 mm Direct Drive Blade Span With: 68" Blade Pitch: 13° no. of Blades: 5 technology: W-74DL - Direct-Touch Lightbulbs: 15-watt Candelabra (6...