Casablanca c12d4301 - Manuals

Page 2 - SaFe uSe; For best performance and for your warranty to be valid,; InTRoducTIon; • The blades in each pack are matched for equal weight; BeFoRe You STaRT

2 circuit Breaker (Trip breaker for the circuit you will be working on) Fuse Box (Remove fuse for the circuit you will be working on) 84” SaFe uSe For best performance and for your warranty to be valid, use only genuine Casablanca blades, light fixtures, and accessories. InTRoducTIon • The blades in...

Page 3 - ottage; MounTInG RecoMMendaTIonS; Ceiling Angle Template; Casablanca offers standard poles in increments of 6” up; Sloped ceIlInG InSTallaTIonS

3 C ottage ™ W et MounTInG RecoMMendaTIonS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. locationCeiling fans have practical uses in almost every room ...

Page 4 - Fan pRepaRaTIon; through the Perma•Lock; Fan InSTallaTIon

4 Fan pRepaRaTIon Perma•Lock™ Hardware (not to scale) Prepare for fan installation as follows:Step 1a. using the provided allen wrench (attached to the paper motor warning shield), loosen the allen set screw attached to the motor coupling.Step 1b. Slide the downrod gasket onto the downrod as shown, ...

Page 5 - it is marked “Approved for Ceiling Fan Mounting.” If it is; GeTTInG STaRTed; NOTE: The weight of this fan is 18 pounds.; ceiLinG Hardware; to reduce the risk of fire, electrical shock, or; canoPy GaSket PreParation; hand; croSSbar mountinG bracket inStaLLation; mounting hardware provided with the approved

5 C ottage ™ W et ceiLinG Hardware (not to scale) using Existing Ceiling fixture outlet Boxafter turning the power off at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for C...

Page 6 - canopY InSTallaTIon; ” long canopy screws (Screw; hanGInG The Fan

6 canopY InSTallaTIon Step 4. attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1 / 2 ” long canopy screws (Screw Pack B) and lock washers provided with your Casablanca fan. tighten using the provided screwdriver until snug against the ceiling. notE: on sloped ceilings, a...

Page 7 - • GREEN leads f rom mounting plate and downrod; canopY elecTRIcal connecTIonS; Perma•Lock; canopY haTch InSTallaTIon

7 C ottage ™ W et Step 6. attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. test that the connection is secure by pulling on the wire nut. Connect in this order: • GREEN leads f rom mounting plate and d...

Page 8 - Blade BadGe InSTallaTIon; badge and install the screw. NOTE: The front of the blade; remove dummy SwitcH HouSinG and SHiPPinG bLockS; Take out the two 5/32-32 x 3/8” screws securing the

8 Blade BadGe InSTallaTIon blade Holder (5) blade badge (5) Screw pack c: Blade Badge Screws (21) Screw pack d: Blade holder Screws (6) bLade Hardware (not to scale) attach Blade HoldersStep 10. using Screw Pack C and the provided screwdriver, carefully align the Medallion nail on the front of the b...

Page 9 - Blade BadGe and Blade holdeR InSTallaTIon; by hand only

9 C ottage ™ W et Blade BadGe and Blade holdeR InSTallaTIon Caution:Blade screws must be tightened securely before operating the fan. SwitcH HouSinG inStaLLation Step 11a. Carefully tilt the blade holder between the switch housing motor plate and the motor, as shown. tiP: Rotate the motor beneath th...

Page 11 - -SPeed • oPtionaL LiGHt Fixture inStaLLation; • Place the switch so that the neck protrudes from

11 C ottage ™ W et 3-SPeed • oPeration Pull-chain switches on the fan control the fan and blade rotation. using the fan control pull-chain switch:fan off at start. • First pull: fan on, low speed • Second pull: medium speed • Third pull: high speed • Fourth pull: fan off 3-SPeed • oPtionaL LiGHt Fix...

Page 12 - TRouBleShooTInG TIpS

12 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TRouBleShooTInG TIpS fan will not operate at proper speeds or will not operate at any speed fan runs slowly in either direction if rotation is started by hand; will not reverse pRoBleM p...

Page 13 - never use abrasive cleaning agents; caRe RecoMMendaTIonS

13 C ottage ™ W et fan finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.• A vacuum cleaner brush nozzle can remove heavier dust.• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly damp...