Casablanca C10GXXM - Manuals

Page 2 - MOUNTING RECOMMENDATIONS; Calculation of 32°; SLOPED CEILING INSTALLATIONS

2 MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. W...

Page 3 - odena; II; INSTALLATION INSTRUCTIONS; Warning: To reduce the risk of fire, electrical; shock, or personal injury, mount to outlet box; CROSSBAR MOUNTING BRACKET INSTALLATION; Proceed with installation as follows:

3 M odena ® II INSTALLATION INSTRUCTIONS IMPORTANT! Leave the fan in the carton until you are ready to hang the fan. CEILING HARDWARE GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ce...

Page 4 - CANOPY HARDWARE

4 ALLEN SET SCREW ¼ -20 (pRE-INSTALLED) 3.18mm ALLEN WRENCH DOWNROD & bALL ASSEmbLy CANOPY INSTALLATION perma•lock™ hardware CANOpy LOCK WASHER CROSSbAR mOUNTINg bRACKET CANOpy Step 3. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1 / 2 ″ long canopy screws and ca...

Page 5 - Prepare for fan installation as follows:; Step 5. Using the provided allen wrench, loosen the set; FAN PREPARATION

5 M odena ® II Prepare for fan installation as follows: Step 4. Route the wires from the motor through the Perma•Lock™ downrod and ball assembly. Step 5. Using the provided allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupli...

Page 7 - INSTALLATION HALOGEN BULB AND GLASS; Step 14. Position the indentations in the outer rim of; Do not touch the bulb with your; NOTE: In compliance with US Federal Energy

7 M odena ® II INSTALLATION HALOGEN BULB AND GLASS Step 13. Screw the 100 Watt Halogen bulb into the socket. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to fail almost immediately. Step 14. Position the indentations in the outer rim of the glass ...

Page 8 - Standard Light Switch

8 Screw 6-32 X 1" (2) Screw 6-32 X 3 / 8 " (2) Wood Screw 1" (2) Drywall Anchor 6-32 (2) 12v Battery W-72 Control W-72 Control Holder VERSA•TOUCH2® COnTROl InSTAllATIOn COnTROl BRACkET InSTAllATIOn Standard Light Switch Step A. Remove the two screws holding the switch cover plate. Do not...

Page 9 - CHAngIng TRAnSmITTER FREqUEnCy SETTIng; REmOTE OpERATIOn

9 Send Signal LED Fan ControlTo start the fan. Press the selected speed button to run the fan at the desired speed. LOW=Low speed MED=Medium speed HIGH=High speed To turn off the fan, press the FAN OFF button. airflow direction To reverse the airflow, press the reVerse button. reVerse operates at an...

Page 10 - TROUBlESHOOTIng TIpS

10 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBlESHOOTIng TIpS pROBlEm pOSSIBlE REmEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the po...

Page 11 - pRODUCT SpECIFICATIOnS

11 M odena ® II 1.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation.2.This equ...