Casablanca 89UXXM - Manuals

Page 3 - arrakesh; cartons and check them against the parts listed in instructions.

3 M arrakesh ™ INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed in instructions. Before discarding packaging material, be certain that all parts have been removed. gETTINg STARTE...

Page 4 - CROSSBAR mOUNTINg BRACKET INSTALLATION; CAUTION: To reduce the risk of personal injury,; LAg SCREW INSTALLATION

4 CROSSBAR mOUNTINg BRACKET INSTALLATION JOIST CEILINg WIRINg CROSSBAR mOUNTINg BRACKET FLAT WASHER gREEN gROUND WIRE CEILINg FAN APPROVED WIRINg BOX RIDgE SIDE DOWN APPROVED OUTLET BOX HARDWARE note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or b...

Page 5 - CANOPY INSTALLATION; BLADE HOLDER, mEDALLION AND BLADE ASSEmBLY; Blade

5 M arrakesh ™ CANOPY INSTALLATION Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 4 1 / 8 ” long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling. CANOPY SCREW CANOPY LOCK WASHER FEED OUTLET BOX WIRES T...

Page 7 - BLADE ASSEmBLY ON FAN INSTALLATION

7 M arrakesh ™ BLADE ASSEmBLY ON FAN INSTALLATION Step 10. Take a blade assembly and insert the foot of the blade iron between the motor adapter and the motor. Step 11. Align one blade iron hole with the appropriate hole in the motor and the cut-out in the the motor adapter. Tighten screw by hand on...

Page 8 - Prepare for fan installation as follows:; CAUTION: Failure to fully lock in the down-

8 BLADE ASSEmBLY ON FAN INSTALLATION Step 12. Rotate blade assembly until the other blade iron hole aligns with the cut-out and again, install and tighten screw by hand only. Repeat steps 11 and 12 until all 3 blade assemblies are installed this way. Perma•lock™ hardware FAN PREPARATION imporTanT sa...

Page 9 - FAN PREPARATION; HANgINg THE FAN

9 M arrakesh ™ FAN PREPARATION Step 17. Align the motor cover key hole slots with the three screws in the motor adapter. Once the cover clears the screw and washers, turn counter-clockwise to engage Step 18 . Securely tighten the screws by hand until snug. KEY HOLE SLOT Step 19. To hang the fan body...

Page 11 - INSTALLINg THE FINIAL

11 M arrakesh ™ INSTALLINg THE FINIAL Step 25. Install the finial onto threads and turn clockwise until snug .

Page 12 - Standard Light Switch; Rocker Light Switch; Wall Installation; ersa

12 Warning: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. SAFETY FIRST SCREW 6-32 X 1” (2) SCREW 6-32 X 3 / 8 ” (2) WOOD SCREW 1” (2) DRYWALL ANCHOR 6-32 (2) 12V BATTERY W-72 CONTROL W-72 CONTROL HOLDER Versa•Touch2 ♦ INSTALLATION Versa•Tou...

Page 14 - TROUBLESHOOTINg TIPS

14 14 TROUBLESHOOTINg TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the...

Page 15 - PRODUCT SPECIFICATIONS; CARE RECOmmENDATIONS

15 M arrakesh ™ 1.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harm- ful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. 2.This ...