Casablanca 86UxxM - Manuals

Page 2 - MOUNTING RECOMMENDATIONS; Location; Calculation of Ceiling Angle

2 7 ′ mINImUm Pole Length Standard Standard 6” 12” 12” 18” 24” 36” 48” Ceiling Height 8’ 8’ 6” 9’ 9’ 6” 10’ 11’ 12’ 13’ 14’ Suggested Extension Pole Lengths BLADES mUST BE A mINImUm OF 7 ′ ABOVE THE FLOOR EXTENSION POLE mAXImUm HANg-TRU® ANgLE 32º 32° MOUNTING RECOMMENDATIONS SLOPED CEILING INSTALLA...

Page 3 - ilderness; ImPORTANT SAFETY INFORmATION!; Prepare for fan installation as follows:; INSTALLATION INSTRUCTIONS

3 W ilderness ™ ImPORTANT SAFETY INFORmATION! BEFORE STARTINg THE INSTALLATION OF YOUR CEILINg FAN, INSTALL THE THREADED DOwNROD INTO THE mOTOR COUPLINg AND LOCK THE ASSEmBLY ALLEN SET SCREw 1 ⁄ 4 -20 x 1 ⁄ 4 ” (PRE-INSTALLED) 3mm ALLEN wRENCH 6” DOwNROD & BALL ASSEmBLY mOTOR COVER Prepare for f...

Page 4 - GETTING STARTED

4 Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either ci...

Page 5 - LAG SCREW INSTALLATION

5 W ilderness ™ CANOPY LOCK wASHER (4) CANOPY SCREw (4) Step 3. Pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We recommend that the ceiling fixt...

Page 6 - CANOPY HATCH INSTALLATION

6 wIRE NUT wHITE wIRES (2) gREEN wIRES (3) Step 6. Attach the fan wires to the ceil- ing fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Connect in this order: • GREEN leads from mounting plate and fan to GROUND conductor of power source. ...

Page 7 - REMOVE DUMMY SWITCH HOUSING & SHIPPING BLOCK

7 W ilderness ™ Step 10. To reach the blade holder mounting holes in the fan motor the switch housing cap must be removed. Take out the two 8-32 X 3 / 8 ” screws securing the switch housing cap and remove. Put the two (2) screws aside for the moment, they will be used in Step 15 to install the switc...

Page 8 - BLADE/BLADE HOLDER INSTALLATION; INSTALLING THE SWITCH HOUSING BRACKETS

8 Step 12. Using the blade holder screws(pack of 11) attach each blade/bladeholder assembly to the motor. Using the screwdriver, tighten securely by hand only. Step 14. Line up the two clearance holes in the cap with the two threaded holes on the raised rim of the switch housing. Press the cap onto ...

Page 9 - INSTALLING OPTIONAL LIGHT FIXTURE

9 W ilderness ™ Step 16. Unpack light fixture and make sure everything is accounted for. Refer to the instruction sheet included with each fixture. Step 17. While holding the light fixture up to the fan connect the wires from the fixture to the wires from the fan. Black to Blue and White to White by...

Page 11 - VERSA•TOUCH2 INSTALLATION; ersa; Rocker Light Switch

11 warning: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. SCREw 6-32 X 1” (2) SCREw 6-32 X 3 / 8 ” (2) wOOD SCREw 1” (2) DRYwALL ANCHOR 6-32 (2) 12V BATTERY w-73 CONTROL HOLDER Standard Light Switch Step A. Remove the two screws holding the...

Page 12 - then back on, for the previously installed versa•touch 2

12 SEND SIgNAL LED Fan Control T o start the fan. Press the selected speed button to run the fan at the desired speed. 1=Low speed 2=medium speed 3=High speed To turn off the fan. Press the FAN OFF button. Airflow Direction To reverse the airflow press the REVERSE button. Reverse operates at any spe...

Page 13 - PROBLEm; VERSA•TOUCH 2; TROUBLESHOOTING

13 V ersa •T ouch 2 ® before Requesting service: please follow this troubleshooting guide before contacting your dealer for assistance. PROBLEm POSSIBLE REmEDIES PROBLEM POSSIBLE REMEDIES .. FAN wILL NOT START •Check main circuit fuses, circuit breakers, or wall switch position. Check all wire conne...

Page 14 - PRODUCT SPECIFICATIONS

14 PRODUCT SPECIFICATIONS Model Name: Wilderness ™ Model Number: 86UxxM Dimensions: A =16" B = 17" C = 3" D = 11.8" E =5.6" Weight: 50 lbs. Motor: 188 x 20mm Direct Drive™ Blade Span: 54” Blade Iron Pitch: 14° No. of Blades: 5 Technology: Versa•Touch2® W-73 Airflow: 6,772 cfm Ele...