Casablanca 79xxD - Manuals - manualsarea.com

Page 2 - MOUNTING RECOMMENDATIONS

2 Calculation of 32 ° Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple ‘go’ or‘no-go’ for installing your fan on a sloped ceiling. 7 ′ MINIMUM When to Use Extension Poles For best performance and best appearance,an extension pole should ...

Page 3 - PREPARATION INSTRUCTIONS; ANAI; PERMA•LOCKTM HARDWARE; IMPORTANT SAFETY INFORMATION!

3 PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check themagainst the parts listed here. Before discarding packaging material, be certain that all parts have been removed. MOTOR COUPLING TAPERED THREAD MOTOR WIRE...

Page 4 - CEILING HARDWARE; GETTING STARTED

4 CEILING HARDWARE CROSSBAR MOUNTING BRACKET WIRE NUT (4) Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wishto place your Casablanca fan, an approved ceiling fixtureoutlet box must be installed and wired. Using Existing Ceiling Fixture Outlet Bo...

Page 5 - CANOPY HARDWARE; CANOPY INSTALLATION

5 CANOPY HARDWARE CANOPY CANOPY HATCH CANOPY LOCK WASHER (4) CANOPY SCREW (4) Step 4. To hang the fan body in the canopy, hold the fan body firmly and in-sert the ball into the canopy opening.Check that no wires were pinched. Ro-tate the fan body until the slot in theball fits into the pin opposite ...

Page 6 - CANOPY HATCH INSTALLATION; CORRECT INSTALLATION; BLADE TO BLADE HOLDER INSTALLATION

6 CANOPY HATCH INSTALLATION RUBBER GROMMET (4 PER BLADE) BLADE SCREW (4 PER BLADE) BLADE HOLDER BLADE HOLDER SCREW (2 PER BLADE) Step 9. Insert a rubber grommet through each blade hole of every blade. Inspectboth sides of the blade to assure thatthe lips of the grommet are fully engaged. Step 6. Tuc...

Page 7 - BLADE INSTALLATION; REMOVE SHIPPING BLOCKS

7 BLADE INSTALLATION Step 12. Using the five screws removed in Step 11, and the five additional screws fromthe pack, attach each blade/blade holder as-sembly to the motor. Using the screwdriver, tighten securely by hand only. Step 10. Attach each blade to a blade holder securing it with the four bla...

Page 8 - INSTALL SWITCH HOUSING CAP SCREWS

8 Step 13. Remove the two screws of the switch housing cap. Set the cap and screwsaside for use in Step 16. REMOVE SWITCH HOUSING CAP SCREWS Step 14. Install 2 of the 3 switch housing screws onto the fan adapter plate, leaving 1 ⁄ 8 " threads visible. Feed the wire connec- tor from the fan throu...

Page 9 - OPERATION; OPTIONAL LIGHT FIXTURE INSTALLATION; TROUBLESHOOTING

9 3-SPEED ♦ OPERATION FAN WILL NOT START Check main circuit fuses, circuit breakers, or wall switch position.Check all wire connections, making sure the power is turned off during this inspection.Check that reverse switch is not set in center of throw. FAN WOBBLES OR SHAKES Be sure canopy pin is pro...

Page 10 - Product SPecificationS

Product SPecificationS Model name: Lanai ® Model number: 79xxD dimensions: A = 11.1" B = 12.75" C = 3" D = 12.6" E = 5.6" Weight: 25 lbs. Motor: 188mm x 20mm Direct Drive ™ Blade Span With: 53" Blade Pitch: 1 6 ° no. of Blades: 5 technology: 3-Speed Airflow: 7,078 cfm electri...