Casablanca 6688Z - Manuals

Casablanca 6688Z – Manual in PDF format online.

Manuals:

Manual

Manual Casablanca 6688Z

Summary

Page 2 - holliston; 6DxxG

2 motor Identification Plate record model aNd SerIal NUmBerS BeFore INSTallaTIoN! Please take a moment to locate the model number and serial number from your fan (see below) and record this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there alr...

Page 3 - anama; Parts Guide

3 P anama ® Item # Description Picture (not to scale) Quantity 1. Motor Housing 1 2. Ceiling plate 1 3. Phillips Screwdriver 1 4. 1 1 / 2 " x 8-32" Roundhead screws and Washers , 2 EA 5. Screw Pack: Lag Screw and Washer (1) 1 EA 6. Wire Nuts (4), 4 7. Canopy and Canopy Hatch 1 8. Perma•Lock™...

Page 5 - Safe USe; unpacking; terials, be certain that all parts have been removed.; for best performance and for your warranty to be valid,; Before YoU STarT

5 P anama ® Circuit Breaker (Trip breaker for the circuit you will be working on) fuse Box (remove fuse for the circuit you will be working on) 18" 70" Safe USe • CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and l...

Page 6 - Calculation of Ceiling Angle

6 MoUNTING reCoMMeNDaTIoNS SLoPeD CeILING INSTaLLaTIoNS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almo...

Page 7 - GeTTING STarTeD; Step 1a�; faN INSTaLLaTIoN

7 P anama ® Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for Ceiling Fan Mounting.” If it is not, a...

Page 8 - faN PreParaTIoN; IMPorTaNT SafeTY INforMaTIoN!; perma•lockTM hardware

8 Prepare for fan installation as follows: 3a. route the wires from the motor through the Perma • Lock™ downrod and ball assembly. 3b. Using the provided allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupling until it stops t...

Page 9 - CaNoPY HarDware

9 P anama ® Step 5. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy open- ing. Check that no wires were pinched. rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. NoTe: Independent control of the light...

Page 10 - CaNoPY HaTCH INSTaLLaTIoN

10 Step 6a. attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order:Step 6b. w-85 wiring Connections • GreeN leads from mounti...

Page 11 - blade/blade Holder inSTallaTion

11 P anama ® ProCeeD To YoUr faN’S CoNTroL feaTUre SeCTIoN for INSTaLLaTIoN/oPeraTING INSTrUCTIoNS: 4-Speed - paGe 12 | INTelI•ToUch3 - paGe 14 blade/blade Holder inSTallaTion Step 10. attach the blades to the blade holders with the three blade screws and flat washers provided for each blade. Hand t...

Page 12 - -Speed • opTIoNal lIGhT FIXTUre INSTallaTIoN

12 Pull-chain switches on the fan control the fan and lights. Using the fan control pull-chain switch: fan off at start. first pull: fan oN, High speed Second pull: Medium speed Third pull: Medium Low speed fourth pull: Low speed fifth pull: fan off Using the optional light pull-chain switch: Light ...

Page 14 - W-85 CoNtroL INStaLLatIoN

14 ® 3 WALL CONTROL AND HARDWARE (not to scale) Switch Mounting Screws (2) Wall Plate Screws (2) White (2) Almond White Wall Plate(1) W-85 Wall Control Switch Bezels (1) White (1) Almond Almond Wall Plate(1) (4) Wire Cap Before installing the W-85 wall control you will need to check and see if you w...

Page 15 - CoNtINueD

15 ® 3 LOCATING PINS (4) figure #5 ALMOND BEZEL BEZEL TABS BEZEL ALIGNMENT PIN AND HOLE figure #3 ALMOND BEZEL RUBBER KEY PAD W-85 Wall Control Bezel replacement: - CoNtINueD Step 17c� Reinstall the rubber key pad on to the four (4) locating pins located on the almond bezel as shown in Figure #3 and...

Page 16 - INSTallING The w-85 wall coNTrol; Wall Control; SINGLe w-85 INSTaLLaTIoN

16 ® 3 INSTallING The w-85 wall coNTrol W-85 CoNtroL INStaLLatIoN 1. Use only the Casablanca W-85 wall control. 2. Do not use any additional control with your Inteli- Touch 3 fan (for example, dimmer, or fan speed control). 3. Do not use more than one fan per wall control.4. No other light fixtures ...

Page 17 - DUaL w-85 INSTaLLaTIoN; dIp SwITcheS; Ensure power is turned OFF at the breaker or fuse panel before

17 ® 3 DUaL w-85 INSTaLLaTIoN To control the fan and lights from two locations (a three-way circuit), use two W-85 wall controls as shown in the wiring diagram in Figure #5. Before installing the two switches into the wall, place both switches side by side, then locate the 4 dip switches on the side...

Page 18 - to vary the light brightness:; oPeraTIoN LIGHTS

18 ® 3 oPeraTIoN Power The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. The button must be left on to retain a previously set fan speed or light level. oPeraT...

Page 19 - CHaNGING freqUeNCY SeTTING; NOTE: All fans leave the factory set to; aUToMaTIC DeMoNSTraTIoN ProGraM; to enter the demonstration program:

19 ® 3 CHaNGING freqUeNCY SeTTING NOTE: All fans leave the factory set to “1111” You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. DIP SwITcheS dIp SwITcheS Set to ‘1111’ (factory Setting) dIp S...

Page 20 - ProGraM

20 ® 3 oPeraTIoN HoMe-Safe ® ProGraM The home-Safe program makes an unoccupied home appear occupied by turning the lights on and off at random times. To enter the Home-Safe Program: 1) To operate the lights and fan for Home Safe Program – Press the But- ton off for a least 5 seconds. 2) Turn the on....

Page 22 - TroUBLeSHooTING TIPS

22 ® 3 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TroUBLeSHooTING TIPS This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) t...