Casablanca 6643050 - Manuals

Page 3 - GETTING STARTED; CROSSBAR MOUNTING BRACKET INSTALLATION; ANAMA

3 Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either the circuit breaker or fuse box), lower the old ﬁ xture and disconnect the wiring. Check the ceiling ﬁ xture outlet box to be sure it is marked “Approved for Ceiling Fan Mounting.” If it is not, a new box m...

Page 4 - FAN PREPARATION; IMPORTANT SAFETY INFORMATION!; PERMA•LOCKTM HARDWARE

4 Prepare for fan installation as follows:3a. Route the wires from the motor through the Perma•Lock™ downrod and ball assembly. 3b. Using the provided allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupling until it stops turn...

Page 5 - CANOPY HARDWARE

5 Step 5. To hang the fan body in the canopy, hold the fan body fi rmly and insert the ball into the canopy open-ing. Check that no wires were pinched. Rotate the fan body until the slot in the nylon ball fi ts into the pin opposite the canopy opening. NOTE: Independent control of the light fi xture...

Page 6 - PULL CHAIN OR; CANOPY HATCH INSTALLATION

6 PROCEED TO YOUR FAN’S CONTROL FEATURE SECTION FOR INSTALLATION/OPERATING INSTRUCTIONS: 4-SPEED - PAGE 7 | INTELI•TOUCH2 - PAGE 9 Install the assembled blade and blade holder to the motor. Hand tighten securely. Repeat for each assembly. FELT WASHER (3 PER BLADE) BLADE HOLDER SCREW (2 PER BLADE HOL...

Page 7 - -SPEED • OPTIONAL LIGHT FIXTURE INSTALLATION

7 Pull-chain switches on the fan control the fan and lights. Using the fan control pull-chain switch: Fan off at start. First pull: fan ON, High speed Second pull: Medium speed Third pull: Medium Low speed Fourth pull: Low speed Fifth pull: Fan OFF Using the optional light pull-chain switch: Light o...

Page 9 - INTELI•TOUCH DUAL W-32 INSTALLATION; Inteli•Touch

9 R R The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed:1. Use onl...

Page 10 - FAN CONTROL; INTELI•TOUCH OPERATION POWER

10 Inteli•Touch ™ R R Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan. To enter the demonstration program: 1. Turn POWER off for at least three seconds. This will clear the fan memory ready for...

Page 11 - INTELI•TOUCH OPERATION LIGHT-MINDER PROGRAM

11 The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: 1. Turn th e POWER OFF for at least three seconds. 2. Turn the 3. Immediately operate the buttons in the following sequence: + + + + + + 4. A series of tones indicates this ...

Page 12 - PROBLEM

12 Inteli•Touch ™ Before Requesting Service: Please follow this troubleshooting guide be- fore contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the fi nish. A vacuum cleaner brush nozzle can remove heavier...

Page 13 - ADVAN•TOUCH CONTROL BRACKET INSTALLATION; ADVAN•TOUCH ATTACH HOLSTER TO BRACKET; SAFETY FIRST; DVAN

13 ADVAN•TOUCH W-62 BRACKET/HOLSTER REMOVAL Step 1. Remove the two 6-32 x 5/16” screws holding the bracket to the holster. Save screws for later. ADVAN•TOUCH CONTROL BRACKET INSTALLATION Standard Light Switch Step A. Remove the two screws holding the switch cover plate. Do not remove the cover plate...

Page 14 - ADVAN•TOUCH OPERATION; ADVAN•TOUCH IMPORTANT OPERATING NOTES; ADVAN•TOUCH BATTERY INSTALLATION

14 I n s t a l l 4 “A A A” a l k a l i n e b a t t e r i e s i n t h e s p a c e p ro v ide d. P l e a s e o b s e r v e proper polarity placement. Replace Battery Door. Open Battery Doorby pressing down on t he i ns e r t t a b p ro -vided. ADVAN•TOUCH OPERATION Fan Operation The Advan•Touch fan is...

Page 15 - ADVAN•TOUCH CHANGING FREQUENCY SETTING; ADVAN•TOUCH IF THE FAN DOES NOT WORK; SECURITY FEATURE

15 1 ON ECE 23 4 5 A4 A4 A4 A4 + + + + – – ADVAN•TOUCH CHANGING FREQUENCY SETTING You will have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. At the circuit breaker or fusebox, turn the power off for t...

Page 16 - TROUBLESHOOTING

16 TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the fi nish. A vacuum cleaner brush nozzle can remove heavier ...