Casablanca 4726D - Manuals - manualsarea.com

Page 2 - SAFE USE; Unpacking

2 4743040 AT0907 18" ↑ 84" ↑ 70" ↑ Circuit Breaker (Trip breaker for the circuit you will be working on) Fuse Box (Remove fuse for the circuit you will be working on) SAFE USE INTRODUCTION • The blades in each pack are matched for equal weight to assure smooth fan operation. If more than...

Page 3 - STRADA; MOUNTING RECOMMENDATIONS; Location; • For safety reasons, the fan blades must be a minimum of 7' above the; Fan Size; GENERAL GUIDELINES; When to Use Extension Poles; Ceiling; SLOPED CEILING INSTALLATIONS

3 E STRADA ™ 4743040 AT0907 MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost ...

Page 4 - Using Existing Ceiling Fixture Outlet Box; NOTE: The weight of this fan is 25 pounds.; Step 1a; . Remove the knockout plug in the center of the; Step 1b; . Route the outlet box wires through the keyhole; CROSSBAR MOUNTING BRACKET INSTALLATION; Support directly to building structure only.

4 4743040 AT0907 GETTING STARTED FAN INSTALLATION Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fi xture and disconnect the wiring. Check the ceiling fi xture outlet box to be sure it is marked “Approved fo...

Page 5 - PERMA•LOCKTM HARDWARE; Prepare for fan installation as follows:; . Route the wires from the motor through the; Step 3b; . Using the provided allen wrench, loosen the set; Step 3c; . Securely tighten the set screw with the provided

5 E STRADA ™ 4743040 AT0907 LAG SCREW INSTALLATION (OPTIONAL) PERMA•LOCK™ HARDWARE FAN PREPARATION NOTE: This step is required only under two conditions: If the fan weighs 36 lbs. or more (which does not pertain to this fan) or if the existing ceiling fi xture outlet box needs to be modifi ed for a ...

Page 6 - CANOPY HARDWARE; . Attach the canopy to the crossbar mounting; HANGING THE FAN; . To ha ng t he fa n body i n t he; CANOPY INSTALLATION

6 4743040 AT0907 CANOPY HARDWARE Step 4 . Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2- ¼ " long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling. NOTE: On sloped ceilings, align the canopy opening towa...

Page 7 - CANOPY ELECTRICAL CONNECTIONS; hand; CANOPY HATCH INSTALLATION

7 E STRADA ™ 4743040 AT0907 Step 6a . Attach the fan wires to the ceiling fi xture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order: Step 6b . Pull-chain Connec...

Page 8 - REMOVE SWITCH HOUSING CAP SCREWS

8 4743040 AT0907 REMOVE SHIPPING BLOCKS Step 10 . On the fl ywheel remove the fi ve shipping blocks by unscrewing the screws. Set these screws aside for installing the blades in Step 11 . Discard the fi ve shipping blocks. BLADE/BLADE HOLDER INSTALLATION Step 11 . Using the fi ve screws removed in S...

Page 9 - INSTALL SWITCH HOUSING; . Install 2 of the 3 switch housing screws onto; CONNECT WIRES; . Plug the wire connector for the fan into the wire; INSTALL SWITCH HOUSING CAP SCREWS; . If you are installing a light fi xture, please refer

9 E STRADA ™ 4743040 AT0907 INSTALL SWITCH HOUSING Step 13 . Install 2 of the 3 switch housing screws onto the fan adapter plate, leaving 1/8" threads visible. Feed the wire connector from the fan through the center of the switch housing. Align the 2 screws on the adapter plate with the keyhole ...

Page 11 - TROUBLESHOOTING TIPS

11 E STRADA ™ 4743040 AT0907 PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. • Check that reverse switch is not set in center of throw. Fan w...

Page 12 - Fan Finishes; never use abrasive cleaning agents; Blades; never use abrasive; No Need for Lubrication; Never lubricate this fan!; Changing Lightbulbs; CARE RECOMMENDATIONS

12 4743040 AT0907 Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the fi nish. • A vacuum cleaner brush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly da...

Page 13 - AUTHORIZED SERVICE CENTERS

13 E STRADA ™ 4743040 AT0907 STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE ALABAMA MOBILE 36618 AZALEA CITY SERVICE CENTER 251-341-0663 TUSCALOOSA 35405 LTG. & APPL./LIGHTING PLUS 205-345-8900 ALASKA ANCHORAGE 99518 BERING SEA ECCOTECH 907-227-3171 ARIZONA TUCSON 85735 DESERT BREEZE FAN & EL...