Casablanca 38DHxxT - Manuals

Page 3 - PERMA•LOCKTM HARDWARE; ir; imporTanT safeTy informaTion!

3 INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. FAN PREPARATION GETTING STARTED Instal...

Page 4 - CROSSBAR MOUNTING BRACKET INSTALLATION; CEILING HARDWARE; SUPPORT INSTALLATION PARTS

4 CROSSBAR MOUNTING BRACKET INSTALLATION JOIST CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT WASHER GREEN GROUND WIRE CEILING FAN APPROVED WIRING BOX RIDGE SIDE DOWN APPROVED OUTLET BOX HARDWARE note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or b...

Page 5 - CANOPY INSTALLATION; CANOPY HARDWARE

5 CANOPY INSTALLATION Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1 / 2 ” long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling. CANOPY SCREW CANOPY LOCK WASHER FEED OUTLET BOX WIRES THROUGH CANOPY...

Page 7 - CANOPY HATCH INSTALLATION; CANOPY ELECTRICAL CONNECTIONS; HANGING THE FAN

7 TILT THE FAN TO INSTALL LAST CANOPY SCREW Step 11. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 13. Straighten the fan, then check to ensure that there is...

Page 8 - CENTER STYLE BLADE HOLDER & BLADE; BLADE HOLDER HARDWARE

8 BLADE SCREW (4 PER BLADE) FLAT WASHER (4 PER BLADE) INSTALLING THE GLASS SHADE INSTALLING THE HALOGEN BULB Step 15. Screw the 100 Watt Halogen bulb into the socket. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean ca...

Page 9 - Inteli•Touch; INTELI•TOUCH DUAL W-32 INSTALLATION

9 The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only t...

Page 10 - FAN CONTROL; LIGHT CONTROL

10 Inteli•Touch ® The POWE button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level. There are s...

Page 11 - After; INTELI•TOUCH OPERATION; INTELI•TOUCH OPERATION; INTELI•TOUCH OPERATION

11 The Light-Minder program automatically turns OFF the fan mounted lights after two hours. To enter the Light-Minder Program: 1. Turn the POWER OFF for at least three seconds. 2. Turn the on. 3. Immediately operate the buttons in the following sequence: + + + 4. A series of tones indicates this com...

Page 12 - PROBLEM

12 Before Requesting Service: Please follow this troubleshooting guide be- fore contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface s...

Page 13 - Product SPecificationS

13 Product SPecificationS Model name: Bel Air ® Halo Model number: 38DHxxT dimensions: A = 13.25" B = 18.5" C = 3" D = 15.5" E = 5.6" Weight: 32 lbs. Motor: XLP-2000 ® Blade Span With: 55" Blade Pitch: 14° no. of Blades: 5 technology: Inteli•Touch ® W-32 Lightbulbs: 100-watt ...