Casablanca 3845Z - Manuals - manualsarea.com

Page 2 - Calculation of 32°; card inserted in the; MINIMUM; SLOPED CEILING INSTALLATIONS

2 Calculation of 32° Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple ‘go’ or ‘no-go’ for installing your fan on a sloped ceiling. 7 ′ MINIMUM Pole Length Standard Standard 6” 12” 12” 18” 24” 36” 48” Ceiling Height 8’ 8’ 6” 9’ 9’ 6” 10” ...

Page 3 - ir; Prepare for fan installation as follows:; COUPLING; iMPortaNt safety iNforMatioN!; BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN,; GETTING STARTED

3 B el A ir ® Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. CROSSBAR MOUNTING BRACKET WIRE NUT (4) Installing a ...

Page 4 - On sloped ceilings, align the; Proceed with installation as follows:; hand; CANOPy INSTALLATION

4 CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mount- ing bracket. CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT WASHER GREEN GROUND WIRE CEILING FAN APPROVED OUTLET BOX RIDGE SIDE DOWN CANOPy LOCk WASHER...

Page 5 - TOP COVER; INSTALLING THE FAN BODy TOP COVER

5 B el A ir ® Step 6. Once the tabs are aligned, attach the top cover to the motor using the three top cover retaining screws removed in Step 3. Hand tighten ensuring that all screws are engaged. Test that the cover is on securely before continuing with the installation. TOP COVER RETAINING SCREWS T...

Page 6 - CANOPy; • GREEN leads from mounting plate; PIN; CANOPy HATCH INSTALLATION

6 TILT THE FAN TO INSTALL LAST CANOPy SCREW Step 9. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 11. Straighten the fan, then check to ensure that there is ...

Page 7 - When installing the halogen bulb,; INSTALLING THE GLASS SHADE

7 B el A ir ® BLADE SCREW (4 PER BLADE) FLAT WASHER (4 PER BLADE) Step 13. Screw the 100 Watt Halogen bulb into the socket. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb w...

Page 8 - To avoid possible electrical shock, make cer-; W-85 CONTROL INSTALLATION

® 3 8 WALL CONTROL AND HARDWARE (not to scale) Switch Mounting Screws (2) Wall Plate Screws (2) White (2) Almond White Wall Plate(1) W-85 Wall Control Switch Bezels (1) White (1) Almond Almond Wall Plate(1) (4) Wire Cap Before installing the W-85 wall control you will need to check and see if you wi...

Page 9 - CONTINUED

® 3 9 Figure #5 ALMOND BEZEL BEZEL TABS BEZEL ALIGNMENT PIN AND HOLE Figure #3 ALMOND BEZEL RUBBER KEY PAD LOCATING PINS (4) W-85 Wall Control Bezel replacement: - CONTINUED Step 17c. Reinstall the rubber key pad on to the four (4) locating pins located on the almond bezel as shown in Figure #3 and ...

Page 10 - INSTALLING THE W-85 WALL CONTROL; If you have multiple Inteli-Touch 3 fans, refer to the section; Wall Control; fans with DOWNLIGHTS ONLY.; SINGLE W-85 INSTALLATION

® 3 1 0 INSTALLING THE W-85 WALL CONTROL 1. Use only the Casablanca W-85 wall control. 2. Do not use any additional control with your Inteli-Touch 3 fan (for example, dimmer, or fan speed control). 3. Do not use more than one fan per wall control. 4. No other light fixtures or electrical appliances ...

Page 11 - DUAL W-85 INSTALLATION; fans within your home you may need to reset the dip switches on; DIP SWITCHES

® 3 1 1 DUAL W-85 INSTALLATION To control the fan and lights from two locations (a three-way circuit), use two W-85 wall controls as shown in the wiring diagram in Figure #5. Before installing the two switches into the wall, place both switches side by side, then locate the 4 dip switches on the sid...

Page 12 - OPERATION REVERSING AIRFLOW; To reverse the airflow:; LIGHT; To vary the light brightness at each touch level:; To vary the light brightness:; Release the button when the desired brightness level is reached.; OPERATION LIGHTS; Light Operation

® 3 1 2 OPERATION POWER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter ad- ditional programs. The button must be left on to retain a previously set fan speed or light level. OPE...

Page 13 - CHANGING FREQUENCY SETTING; NOTE: All fans leave the factory set to; DIP; AUTOMATIC DEMONSTRATION PROGRAM; To enter the demonstration program:; NOTE: DO NOT set dip switch setting in the remote

® 3 1 3 CHANGING FREQUENCY SETTING NOTE: All fans leave the factory set to “1111” You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. Turn power OFF at the circuit breaker or fuse box and ...

Page 14 - ) To operate the lights for Light Minder Program – Press the

® 3 1 4 OPERATION HOME-SAFE ® PROGRAM The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times. To enter the Home-Safe Program: 1) To operate the lights and fan for Home Safe Program – Press the Button off for a least 5 seconds. 2) Turn the on. ...

Page 15 - PROGRAM

® 3 1 5 OPERATION FAN-MINDER ™ PROGRAM The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for cooling night air. To enter the Fan-Minder Program: 1. Turn the OFF for at least 5 seconds. 2. Turn the O...

Page 16 - TROUBLESHOOTING TIPS; the blades are balanced.

® 3 1 6 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBLESHOOTING TIPS This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) ...

Page 17 - PRODUCT SPECIFICATIONS; Bel Air

17 PRODUCT SPECIFICATIONS Model Name: Bel Air ® Model Number: 38xx = Dimensions: A = 8.6" B = 13.9" C = 2.8" D = 12.2" E = 5.6" Weight: 24 lbs. Motor: XLP-2000 ® Blade Span With: 55" Blade Pitch: 14° No. of Blades: 5 Technology: I nteli•Touch ® Lightbulbs: 100-watt halogen (1...