Casablanca 32xxA - Manuals - manualsarea.com

Page 3 - Prepare for fan installation as follows:; imporTanT safeTy informaTion!

3 Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. STEALTH INSTALLATION INSTRUCTIONS FAN PREPARATION PERMA•LOCK™ HA...

Page 4 - CROSSBAR MOUNTING BRACKET INSTALLATION; CEILING HARDwARE; SUPPORT INSTALLATION PARTS

4 CROSSBAR MOUNTING BRACKET INSTALLATION JOIST CEILING wIRING CROSSBAR MOUNTING BRACKET FLAT wASHER GREEN GROUND wIRE CEILING FAN APPROVED wIRING BOX RIDGE SIDE DOwN APPROVED OUT- LET BOX HARDwARE note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or...

Page 5 - CANOPY INSTALLATION; CANOPY HARDwARE

5 CANOPY INSTALLATION Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1 / 2 ” long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling. CANOPY SCREw CANOPY LOCK wASHER FEED OUTLET BOX wIRES THROUGH CAN- O...

Page 6 - CANOPY ELECTRICAL CONNECTORS

6 Step 4. To hang the fan body in the canopy, support the fan at the center of the glass holder and top support and insert the ball into the canopy opening. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. HANGING FAN BODY IN CANOPY BLADE HOLDER BLADE TIP...

Page 7 - BULB INSTALLATION

7 TILT THE FAN TO INSTALL LAST CANOPY SCREw BULB INSTALLATION CANOPY HATCH INSTALLATION CANOPY CANOPY LOCK wASHER CANOPY SCREw Step 6. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the white and black wires are on opposite sides of the canopy and all wires are clear of t...

Page 8 - only; one fan per wall control; Inteli•Touch; INTELI•TOUCH DUAL W-32 INSTALLATION; INTELI•TOUCH INSTALLING THE W-32 WALL CONTROL

8 The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the following precautions must be observed: 1. Use only t...

Page 9 - FAN CONTROL

9 Inteli•Touch ® Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan. To enter the demonstration program: 1. Turn POwER off for at least three seconds. This will clear the fan memory ready for prog...

Page 10 - After; INTELI•TOUCH OPERATION; INTELI•TOUCH OPERATION; INTELI•TOUCH OPERATION

10 Inteli•Touch ® The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. To enter the Safe-Exit Program: 1. Turn the POwE off for at least three seconds. 2. Turn the POwE on. 3. Immediately operate the butt...

Page 11 - PROBLEM

11 Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smu...

Page 12 - ADvAN•TOUCH CONTROL bRACkET INSTALLATION; Standard Light Switch; Rocker Light Switch; wall Installation; ADvAN•TOUCH ATTACH HOLSTER TO bRACkET; SAFETY FIRST; DVAN

12 ADvAN•TOUCH W-62 bRACkET/HOLSTER REmOvAL Step 1. Remove the two 6-32 x 5/16” screws holding the bracket to the holster. Save screws for later. ADvAN•TOUCH CONTROL bRACkET INSTALLATION Standard Light Switch Step A. Remove the two screws holding the switch cover plate. Do not remove the cover plate...

Page 13 - ADvAN•TOUCH bATTERY INSTALLATION

13 I ns t a l l 4 “A A A” a l ka l i ne b a t t e r i e s i n t h e s p a c e provided. Please observe proper polarity placement. Replace Battery Door. Open Battery Door by pressing down on t he i ns e r t t a b p ro - vided. ADvAN•TOUCH OPERATION Fan Operation The Advan•Touch fan is controlled by t...

Page 14 - ADvAN•TOUCH CHANGING FREqUENCY SETTING; You will have to change the dip switch settings in the; ADvAN•TOUCH IF THE FAN DOES NOT WORk; If the fan is not functioning after installation:; SECURITY FEATURE

14 ADvAN•TOUCH CHANGING FREqUENCY SETTING You will have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. At the circuit breaker or fusebox, turn the power off for the fan you want to change. Step 2. Open ...

Page 15 - TROUBLESHOOTING

15 TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier d...

Page 16 - PRODUCT SPECIFICATIONS

16 PRODUCT SPECIFICATIONS Model Name: Stealth ® Model Number: 32xxA/T Dimensions: A = 10.8" B = 13.25" C = 3" D = 11.5" E = 5.6" Weight: 33 lbs. Motor: XLP-2000 ® Blade Span: 54" Blade Iron Pitch: 14° No. of Blades: 5 Technology: Advan•Touch ® W-62 Inteli•Touch ® W-32 Lightbu...