Casablanca 3211Z - Manuals - manualsarea.com

Page 2 - When to Use Extension Poles

2 Calculation of 32° Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple ‘go’ or ‘no-go’ for installing your fan on a sloped ceiling. SLOPED CEILING INSTALLATIONS MOUNTING RECOMMENDATIONS 7’ minimum Pole Length Standard Standard 6 ″ 12 ″ 12...

Page 3 - Prepare for fan installation as follows:; failure to fully lock in the downrod; IMpOrTaNT saFeTy INFOrMaTION!

3 S tealth ® Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. STEALTH INSTALLATION INSTRUCTIONS FAN PREPARATION PER...

Page 4 - CROSSBAR MOUNTING BRACkET INSTALLATION; Note: after removing the old fixture, check the outlet; CAUTION: To reduce the risk of personal; CEILING HARDwARE; SUPPORT INSTALLATION PARTS; SUPPORT DIRECTLY TO

4 CROSSBAR MOUNTING BRACkET INSTALLATION JOIST CEILING wIRING CROSSBAR MOUNTING BRACkET FLAT wASHER GREEN GROUND wIRE CEILING FAN APPROVED wIRING BOX RIDGE SIDE DOwN APPROVED OUTLET BOX HARDwARE Note: after removing the old fixture, check the outlet box to insure that it is supported by a joist or b...

Page 5 - box is firmly mounted to beam. This box must be firmly; LAG SCREw INSTALLATION

5 S tealth ® CANOPY INSTALLATION Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1 / 2 ” long canopy screws and lock washers provided with your Casablanca fan. Hand tighten until snug against the ceiling. CANOPY SCREw CANOPY LOCk wASHER FEED OUTLET BOX wIRES THR...

Page 7 - tealth; BULB INSTALLATION; Do not touch the glass bulb with your fingers–it is ex; INSTALLING THE GLASS; face of the fan light fixture rim.

7 S tealth ® TILT THE FAN TO INSTALL LAST CANOPY SCREw BULB INSTALLATION CANOPY HATCH INSTALLATION CANOPY CANOPY LOCk wASHER CANOPY SCREw Step 6. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the white and black wires are on opposite sides of the canopy and all wires are...

Page 8 - W-85 Wall Control Bezel Replacement installation; To avoid possible electrical shock, make cer-; W-85 CONTROl INSTAllATION

8 ® 3 WALL CONTROL AND HARDWARE (not to scale) switch Mounting Screws (2) Wall Plate Screws (2) White (2) Almond White Wall Plate(1) W-85 Wall Control Switch Bezels (1) White (1) Almond Almond Wall Plate(1) (4) Wire Cap Before installing the W-85 wall control you will need to check and see if you wi...

Page 9 - CONTINUED

9 ® 3 Figure #5 aLMOND BEZEL BEZEL TABS BEZEL aLIGNMeNT PIN AND HOLE Figure #3 aLMOND BEZEL RUBBER KEY PAD W-85 Wall Control Bezel replacement: - CONTINUED Step 17c. Reinstall the rubber key pad on to the four (4) locating pins located on the almond bezel as shown in Figure #3 and #4. Step 17d. To a...

Page 10 - INSTAllINg ThE W-85 WAll CONTROl; If you have multiple Inteli-Touch 3 fans, refer to the section; Wall Control; SINGLE w-85 INSTALLATION

10 ® 3 INSTAllINg ThE W-85 WAll CONTROl 1. Use only the Casablanca W-85 wall control. 2. Do not use any additional control with your Inteli-Touch 3 fan (for example, dimmer, or fan speed control). 3. Do not use more than one fan per wall control. 4. No other light fixtures or electrical appliances m...

Page 11 - DUAL w-85 INSTALLATION; fans within your home you may need to reset the dip switches on; DIP SWITChES; screws holding the switch in the switch box.

11 ® 3 DUAL w-85 INSTALLATION To control the fan and lights from two locations (a three-way circuit), use two W-85 wall controls as shown in the wiring diagram in Figure #5. Before installing the two switches into the wall, place both switches side by side, then locate the 4 dip switches on the side...

Page 12 - The direction of airflow can be changed from down; lIghT; To vary the light brightness:; OPERATION LIGHTS; light operation

12 ® 3 OPERATION POwER The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. The button must be left on to retain a previously set fan speed or light level. OPERAT...

Page 13 - CHANGING FREqUENCY SETTING; noTe: all fans leave the factory set to; DIP; AUTOMATIC DEMONSTRATION PROGRAM

13 ® 3 CHANGING FREqUENCY SETTING noTe: all fans leave the factory set to “1111” You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. Turn power OFF at the circuit breaker or fuse box and a...

Page 14 - PROGRAM; ) To operate the lights and fan for Home safe program – press the; OPERATION SAFE-EXIT; ) To operate the lights for Light Minder program – press the

14 ® 3 OPERATION HOME-SAFE ® PROGRAM The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times. To enter the Home-Safe Program: 1) To operate the lights and fan for Home safe program – press the But- ton off for a least 5 seconds. 2) Turn the on....

Page 15 - OFF for at least 5 seconds.

15 ® 3 OPERATION FAN-MINDER ™ PROGRAM The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for cooling night air. To enter the Fan-Minder program: 1. Turn the OFF for at least 5 seconds. 2. Turn the ON...

Page 16 - TROUBLESHOOTING TIPS; the “Fan” and “REVERSE” buttons as shown in Figure #2 for 3 seconds,

16 ® 3 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBLESHOOTING TIPS This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) t...

Page 17 - PRODUCT SPECIFICATIONS; stealth

17 S tealth ® PRODUCT SPECIFICATIONS Model Name: stealth ® Model Number: 32xxZ Dimensions: A = 10.8" B = 13.25" C = 3" D = 11.5" E = 5.6" Weight: 33 lbs. Motor: XLp-2000 ® Blade Span: 54" Blade Iron Pitch: 14° No. of Blades: 5 Technology: Inteli•Touch ® 3 W-85 Lightbulb: (1) ...