Page 2 - Page; Due to variations in environmental conditions, it is not; TOTALINE; CAUTION
Page i NOTE: Due to variations in environmental conditions, it is not always possible to achieve the desired humidification or dehumidification setpoint. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful in...
Page 3 - ii; Timers and Deadbands; section, such as the example page shown below.; regarding this thermostat quickly.; How to Use This Manual; Section contents
Page ii Page 14.1 Section 14 Contents: Adjusting the Heat/Cool Differential..............................14.2 Adjusting the Cycles Per Hour..................................14.3 Adjusting the Deadband..........14.4 Adjusting the Minutes of Run-Time Before the Next Stage.................................
Page 4 - Glossary of Terms; iii; Configurable Output Jumper:
TOTALINE Glossary of Terms Glossary of Terms Page iii Auto-Changeover: A mode in which the thermostat will turn on the heating or cooling based on room temperature demand. Configurable Output Jumper: Using jumpers on the thermostat you can configure the MISC1, MISC2, and MISC3 terminals to operate w...
Page 6 - iv; Table of Contents
2 1 3 6 7 89 10111213141516 17 181920 212223 24 45 Quick Start Getting to Know Your ThermostatSetting Clock and Day Basic Operation Viewing Temperature and Humidity Programming the Daily ScheduleProgramming the Fan OperationThermostat Display Options Humidification Dehumidification Viewing Equipment...
Page 7 - Following the instructions in this section will allow you to; SECTION 1; Quick Start
Page 8 - Setting the Clock
Buttons. To adjust the Clock or Day use Press the MODE andHUMIDITY buttons at the same time Press the MODE and HUMIDITY buttons at the same time to return to normal operation. Su Setup 2 Am I2:00 Setup I Setting the Clock Setting the Clock During Setup & Programming: Pressing the UP or DOWNbutto...
Page 9 - Select Mode by Pressing the MODE Button
Selecting the Heat or Cool Mode Selecting the Heat or Cool Mode Press MODE Press MODE Press MODE Press MODE H EAT I2:00 Su 70 Pm 68 C OOL I2:00 Su 70 Pm 76 H EAT C OOL AUTO I2:00 Su 70 Pm 68 76 H EAT C OOL I2:00 Su Program On 70 Pm 68 76 OFF I2:00 Su 70 Pm occupied Program On will activate the store...
Page 10 - Adjust the desired; Selecting Your Desired Temperature; Using the Fan Button; Fan On; and
AUTO OR PROGRAM MODE Pressing the UP or DOWN buttons in Auto or Program mode will adjust both the heat and cool set temperatures simultaneously. buttons. Adjust the desired set temperature with the H EAT C OOL AUTO I2:00 Su 70 Pm 68 76 HEAT OR COOL MODE Pressing the UP or DOWN buttons in Heat or Coo...
Page 11 - SECTION 2; Getting to Know Your Thermostat
Section 2 Contents: Front Panel Buttons.....................2.2 Display Features...........................2.3 Page 2.1 SECTION 2 Getting to Know Your Thermostat Getting to Know Your Thermostat TOTALINE 2
Page 12 - Front Panel
HUMIDITY FAN MODE PROGRAM HOLIDAY OVER RIDE SET CLOCK OUTSIDE HUMIDITY AUTO I2:00 Su Pm H EAT C OOL 72 74 FAN MODE SET CLOCK PROGRAM HOLIDAY OUTSIDE Premier CommercialProgrammable Thermostat Backlit LCD Display OverrideButton Heat or Cool Demand Indicator Red = Heat, Green = Cool TOTALINE AUTO I2:00...
Page 13 - Unoccupied; DeHumidify; Outside; Display Features; Section 4
AUTO OFFON Override Unoccupied Am I8:88 SuMoTuWeThFrSa Pm A UX H EAT C OOL FanOn Service FilterPan UV Light Program On StartStop DeHumidify I88 Setup Outside Remote 88 L O H I 88 1 2 3 2 Display Features Display Features TOTALINE Mode Indicators - Section 4 Selects the operational mode of the equipm...
Page 14 - Section 6
AUTO OFFON Override Unoccupied Am I8:88 SuMoTuWeThFrSa Pm A UX H EAT C OOL FanOn Service FilterPan UV Light Program On StartStop DeHumidify I88 Setup Outside Remote 88 L O H I 88 1 2 3 2 Page 2.4 TOTALINE Display Features Display Features Occupied & Unoccupied icons - Section 6 Indicates the pro...
Page 15 - AUTO
Remote icon - Indicates the remote sensor reading of the thermostat is being viewed. AuxHeat icon - Indicates the Heat Pump is currently using 2nd stage heat. Humidify/DeHumidify icon - Indicates the system is currently humidifying/dehumidifying the air. Lo icon - Indicates the lowest recorded outsi...
Page 16 - SECTION 3; Setting the Clock and Day
Page 18 - SECTION 4; Basic Operation
Section 4 Contents: Programming for Auto or Program Operation....................4.2 Selecting the Proper Operating Mode.........................4.3 Selecting Your Desired Temperature...............................4.7 Page 4.1 Note: During setup & programming pressing the UP or DOWN buttons will...
Page 19 - Select ‘YES’ if you would like your thermostat to be; programmable
Page 21 - Select the Mode by Pressing the MODE Button
Press MODE Press MODE H EAT I2:00 Su 70 Pm 68 C OOL I2:00 Su 70 Pm 76 OFF I2:00 Su 70 Pm NON-PROGRAMMABLE WITH MANUAL-CHANGEOVER - If the thermostat is configured to be a non-programmable thermostat with Manual-Changeover, the following screens will be available by pressing the MODE button. Page 4.4...
Page 26 - SECTION 5; Viewing the Temperature and Humidity Sensors
Section 5 Contents: Viewing the Outside Temperature..............................5.2 Viewing the Indoor Humidity....................................5.3 Page 5.1 SECTION 5 Viewing the Temperature and Humidity Sensors Viewing the Temperature and Humidity Sensors TOTALINE 5
Page 27 - buttons. The display will then show the current; Viewing the Outside Temperature
The High and Low temperatures for the day will be displayed along with the current outsidetemperature. This reading is from the sensor connected to RS2. 83 Outside 68 L O H I 92 Requires an outside sensor (optional accessory) to be installed. To read the temperature from the Outside Sensor, press th...
Page 28 - Current Room Humidity; Viewing the Indoor Humidity
To view the indoor humidityreading, press the HUMIDITY button HUMIDITY Press HUMIDITY 40 Humidify Setup I Current Room Humidity Requires the Humidity Module (optional accessory) to be installed. To display the current humidity at the thermostat, press the HUMIDITY button of the thermostat. The displ...
Page 29 - SECTION 6; Programming the Daily Schedule
Section 6 Contents: Programming a Daily Schedule...................................6.2 Overriding the Daily Schedule...................................6.6 TOTALINE Page 6.1 SECTION 6 Programming the Daily Schedule Programming the Daily Schedule 6
Page 30 - Programming a Daily Schedule
Press the PROGRAM button to enter time period programming. Continued Use the Programming Worksheet on the back cover to help with this section. Press PROGRAM Page 6.2 Programming a Daily Schedule Programming a Daily Schedule Press MODE Press MODE Press MODE Press MODE occupied C OOL 74 occupied H EA...
Page 33 - PROGRAMMING TIPS
Page 34 - Unoccupied Operation -; During programmed, unoccupied; Occupied Operation -
Page 35 - SECTION 7; Programming the Fan Operation
TOTALINE Section 7 Contents: Using the Fan Button.................7.2 Setting the Fan-Off Time Delay..........................................7.3 Fan Purge Operation..................7.4 Page 7.1 SECTION 7 Programming the Fan Operation Programming the Fan Operation 7
Page 37 - Setting the Fan-Off Time Delay
Set the Fan Off Delayto 0, 30, 60, or 90 seconds. FanOn Setup 3 Press the PROGRAM button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds. PROGRAM Press Page 7.3 Setting the Fan-Off Time Delay Setting the Fan-Off Time Delay To increase ...
Page 38 - Fan Purge Operation
When this feature is activated, the fan will turn on during an unoccupied period at a preset amount of time prior to Occupied 1. This preoccupancy fan purge timer may be set from zero to three hours. Zero means this feature is turned off. Press the PROGRAM button to leave the Setup screens. If no bu...
Page 39 - SECTION 8; Thermostat Display Options
TOTALINE Section 8 Contents: Turning On/Off the Backlight...................................8.2 Programming the Thermostat to Display Temperature in Fahrenheit or Celsius..............8.2 Locking/Unlocking the Keypad......................................8.3 Programming a Security Level.................
Page 40 - Turning On/Off the Backlight
Press the PROGRAM button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds. Press MODE PROGRAM Press Page 8.2 Turning On/Off the Backlight Turning On/Off the Backlight PROGRAM MODE MODE Press the MODE button. While holding the MODE, pres...
Page 41 - Locking/Unlocking the Keypad; unlock
Page 42 - Programming a Security Level
Select the security level:0=No security in effect1=Setpoint range limited2=1+ program on all times3=2 + prohibits setpoint changes Adjust the minimumallowable cool setpointwhen security is in effect. (35 - 99 ) Press MODE Press MODE Press the PROGRAM button to leave the Setup screens. If no buttons ...
Page 43 - SECTION 9; Humidification
Page 44 - Figure 2; Installing the Humidity Module; HUM; OR; Install the Humidity Module
Page 45 - see diagram below; IMPORTANT CAUTION
ECON Page 9.3 Setting a Thermostat Jumper for Humidity Operation Setting a Thermostat Jumper for Humidity Operation NEVER PUT MORE THAN ONE JUMPER ON THE SAME MISC JUMPER BLOCK! THIS MAY DAMAGE THE THERMOSTAT AND VOID YOUR WARRANTY To operate one of the MISC outputs using humidity-based operation, p...
Page 46 - Adjusting the Humidification Setpoint; Humidification Notes:
Press the HUMIDITY button to leave the Humidity Control screens (if no buttons are pressed, the display will leave the Humidity Control screens after 30 seconds). HUMIDITY Adjust the desired humidification setpoint (0%-60%) NOTE: Each step # is located at the top right corner of the display for easy...
Page 47 - Dehumidification
TOTALINE Page 10.1 NOTE: The dehumidification functions described in this section will only be available if a Humidity Module has been properly installed. For instructions on installing the Humidity Module please see page 9.2. Section 10 Contents: Configuring a Thermostat Output Jumper for Dehumidif...
Page 48 - jumper on the terminal labeled DEHUM (
ECON Page 10.2 Setting a Thermostat Jumper for Dehumidification Operation Setting a Thermostat Jumper for Dehumidification Operation NEVER PUT MORE THAN ONE JUMPER ON THE SAME MISC JUMPER BLOCK! THIS MAY DAMAGE THE THERMOSTAT AND VOID YOUR WARRANTY MISC3 MISC3 OK To operate one of the MISC outputs u...
Page 49 - If your HVAC unit is equipped with a dehumidification terminal; Adjusting the Dehumidification Setpoint; Dehumidification Notes:
Press the HUMIDITY button to leave the Humidity Control screens (if no buttons are pressed, the display will leave the Humidity Control screens after 30 seconds). Press the HUMIDITY buttonto enter the Humidification Setup screens. HUMIDITY Adjust the desired dehumidification setpoint (25%-99%) NOTE:...
Page 50 - I i
Page 52 - Normally Closed
Page 54 - This feature enables you to closely monitor your; W1 terminal only
Page 55 - Y1 terminal only
Page 56 - button to reset the counter.; Viewing the Override Operation Run-Time
Press the PROGRAM button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds. PROGRAM Press This display will track the number of hours that your thermostat has been operating in the Override mode ( see page 6.6 ). Press the FAN button to ...
Page 57 - Viewing the Humidification Run-Time
Press the PROGRAM button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds. PROGRAM Press After your humidification system has been operating for the number of days set in step #17 below, the Service Humidify icon will appear. This count...
Page 61 - EH
Page 62 - During Emergency Heat operation the; Using Emergency Heat
ENTER EMERGENCY HEAT: Only available if you have a Heat Pump installed. To initiate the Emergency Heat feature, press the FAN button. While holding the FAN button press UP button. The Cool setpoint display will read ‘EH’ (emergency heat). the Press for Emergency Heat FAN H EAT I2:00 73 Pm 74 Page 12...
Page 64 - To increase the spread between the heating and cooling
Page 65 - Cy
Page 66 - nd Stage; the setpoint; rd Stage
Page 70 - Using the Programmable Output
TOTALINE Page 14.1 Section 14 Contents: Configuring a Thermostat Output Jumper for Programmable Output Operation...................14.2 Time-Based Control of the Programmable Output...........14.3 Temperature-Based Control of the Programmable Output.....14.6 Internet/Phone Control of the Programmabl...
Page 72 - below; TIME
Press the UP button to set the programmableoutput for time based operation. The digits in the clock area will appear. Setup 30 Page 14.3 Time-Based Control of the Programmable Output Time-Based Control of the Programmable Output To operate one of the MISC outputs using time-based operation, set the ...
Page 75 - TEMPERATURE
Page 76 - Possible; REMOTE
Possible REMOTE scenarios: 1) Arm the alarm system in your building after you have left for the day. 3) Turn on your interior lights while you’re closed. 2) Turn off your sign lights after arriving home. Page 14.7 Internet/Phone Control of the Programmable Output Internet/Phone Control of the Progra...
Page 78 - unshielded, thermostat; See the Remote Sensor accessory for further details.; This wire
Page 80 - see below
Page 81 - Programming the Dry Contact
TOTALINE Page 16.1 Section 16 Contents: Dry Contact Operation............ 16.2 Dry Contact Polarity.................16.2 Dry Contact Programming.......16.3 Random Start Operation..........16.4 SECTION 16 Programming the Dry Contact Programming the Dry Contact 16
Page 83 - Occupied 1
Page 84 - Loss of Power to the thermostat:; When power to the thermostat
Page 85 - Light Activated Operation
TOTALINE Page 17.1 Section 17 Contents: Setting up the Thermostat for Light Activated Operation................................17.2 Adjusting the Light Sensor.....17.3 SECTION 17 Light Activated Operation Light Activated Operation 17
Page 86 - Light Sensor
Select YES if the thermostat should be Light Activated.Select NO to allow only Time Period Programming ( Section 6 ). Press the PROGRAM button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds. PROGRAM Press A light sensor is provided on...
Page 88 - If the thermostat is configured to be programmable (; Energy Save Operation
Page 89 - Programming Run-Time Alarms
TOTALINE Page 19.1 Section 19 Contents: Setting and Resetting the Service Filter (Fan Run-Time) Alarm........................................19.2 Setting and Resetting the UV Light Run-Time Alarm.............19.3 Setting and Resetting the Humidify Run-Time Alarm......19.4 SECTION 19 Programming Run-...
Page 93 - Programming Holiday Mode
Page 94 - see previous page
Page 95 - Configuring the MISC Outputs
TOTALINE Page 21.1 Section 21 Contents: Configuring the Jumpers........21.2 Explanation of Jumper Settings..................................21.3 SECTION 21 Configuring the MISC Outputs Configuring the MISC Outputs 21
Page 97 - PROG JUMPER SETTING; W3 JUMPER SETTING; Explanation of Jumper Settings; And; Time
PROG JUMPER SETTING If the jumper for MISC1, MISC2, or MISC3 is set to PROG, the corresponding MISC screwterminal on the backplate will control a pilot relay or other accessory. Page 21.3 The 3rd Stage of Heat is turned on when: (A) The 1st and 2nd stages have been on for the time required ( steps 2...
Page 98 - DEHUM JUMPER SETTING; energize
HUMIDIFICATION OPERATION - SECTION 9 If your HVAC unit is equipped with a humidification system and the Humidity Module (sold separately) has been installed, the thermostat will provide power to the MISC1, MISC2, or MISC3 terminal of the thermostat when the humidity in the home falls below the humid...
Page 99 - Cooling
ECON JUMPER SETTING If the jumper for MISC1, MISC2, or MISC3 is set to ECON, the corresponding MISC screw terminal on the backplate will be connected to an economizer. ECONOMIZER OPERATION - If your HVAC unit is equipped with an economizer system, the thermostat will provide power to the MISC1, MISC...
Page 102 - After calibration is complete, press the MODE button; to view all of your; twice; to return to normal operation.; Calibrating the Temperature and Humidity Sensors
After calibration is complete, press the MODE button once to view all of your wired remote sensors ( next page ) or twice to return to normal operation. AUTO OFFON Override Unoccupied Am I8:88 SuMoTuWeThFrSa Pm A UX H EAT C OOL FanOn Service FilterPan UV Light Program On StartStop DeHumidify I88 Set...
Page 103 - Because e
Page 104 - Accessories
TOTALINE Page 23.1 SECTION 23 Accessories Accessories RJ11 Type Jack The Accessory Port is located on the bottom of the thermostat. EZ PROGRAMMER (optional accessory) - When the EZ is connected, the thermostat Time Period Advanced Setup Programming can be stored into memory. This information can the...
Page 105 - Advanced Setup Table
TOTALINE 24 Description Df* Step# Range Step# Description Range Df* 2 2 On Off NO Off Mo 7am 9pm 80 Yes Off No NOOcc.1 NoOff- - 0 0 0 - - 1 2 3 45 6789 10 11 1213 14 15 1617 1819 20 2122 2324 25 26 Programmable ThermostatAuto-Changeover ThermostatFan Off Delay Fan PurgeThermoglow BacklightF or CSecu...
Page 106 - Index
Page 112 - Warranty
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing,repairing, removing, installing, shipping, servicing or handling of either defective parts orreplacement parts. Such costs may be covered by a separate warranty provided by the installer. THIS WARRANTY APPLIES ONLY TO PRODUC...
Page 113 - Programming Worksheet; see Section 6; DAY PERIOD
Programming Worksheet see Section 6 No Yes No Yes No Yes No Yes No Yes No Yes F R I D A Y T U R A S D A Y Copy Fri Sat Copy Tue Wed Copy Thu Fri S U N D A Y Copy Sat Sun Copy Wed Thu W E N E S D D A Y T U R H S D A Y Copy Mon Tue M O N D A Y T U E S D A Y DAY PERIOD HEAT START TIME COOL Unoccupied O...
Carrier 58CTA09010016
User Manual