Carrier ERVCCSVB1100- Manuals

5 PHYSICAL DATA MODEL ERVCCSVB1100 ERVCCSHB1100 HRVCCSVB1100 HRVCCSHB1100 Port Locations Top Side Top Side Core Type Enthalpic transfer media with plastic stack Enthalpic transfer media with plastic stack Polypropylene Cross Flow Polypropylene Cross Flow Core Exchange Area 56 sq. ft. (5.2m 2) 56 sq....

6 PERFORMANCE DATA HVI Rated Energy Performance MODEL MODE SUPPLY TEMP NET AIR FLOW POWER CONSUMED (WATTS) SENSIBLE RECOVERY EFFICIENCY APPARENT SENSIBLE EFFECTIVENESS LATENT RECOVERY MOISTURE TRANSFER TOTAL RECOVERY EFFICIENCY _ C _ F L/S CFM ERVCCSH B1100 Heating 0 32 21 45 42 68 79 0.63 0 32 27 5...

5 between wall control and ERV/HRV connector following colorcode. (See Fig. 5 and 10.) Replace top cover assembly. NOTE : ERV/HRV wall control and circuit board operate on 12VDC. YELLOW Y R G B RED GREEN BLACK A98383 Fig. 10 -- Typical Wall Control Operation The Standard and Latent wall controls hav...

6 OPERATING THE ERV/HRV WITH THE INFINITY CONTROL The ventilator has four settings in heating mode and three settings in cooling mode. Heating: AUTO -- the ventilator selects the speed based on indoorhumidity and outdoor temperature. It may cycle on/off every 30 minutes depending on humidity and out...

7 BALANCING ERV/HRV Balancing intake and exhaust airflow is very important for propersystem operation and optimum performance when applying an ERV/HRV. Unit balancing prevents a positive and/or negativepressure within the home. Balancing the ERV/HRV is done by applying magnehelic gauge and using the...

8 VENTILATION EVALUATION UNIT DAMAGE HAZARD Failure to follow this caution may result in reduced unit efficiency, capacity or unit life.DO NOT use HRV during construction of a house or when sanding drywall. This type of dust may damage system. CAUTION ! Ventilator Sizing Tables 3 and 4 should be use...

9 NOTE : The core should only be serviced when outdoor temperature is 60 ° F to 75 ° F (16 ° C to 24 ° C) and it is dry. UNIT COMPONENT DAMAGE HAZARD Failure to follow this caution may result in equipment damage or improper operation.DO NOT use water to clean core or damage will result. In addition,...

10 If the integrated control LED of the unit is flashing, this means the unit sensors detected a problem. See the table below to know where on theunit the problem occurs. Table 5 – Troubleshooting LED flashes GREEN. Thermistor error. Reference Table 6 for proper temperature vs. resistance relationsh...

11 Table 6 – Temperature / Ohm Relationship TEMP. ( ° F / ° C) RESISTANCE (OHMS) --- 9 / --- 23 78330 --- 8 / --- 22 74610 --- 6 / --- 21 71100 --- 4 / --- 20 67770 --- 2 / --- 19 64570 --- .4 / --- 18 61540 1 / --- 17 58680 3 / --- 16 55970 5 / --- 15 53410 7 / --- 14 50980 9 / --- 13 48680 10 / --...

12 CONNECTION DIAGRAM Line voltage factory wiring Class 2 low voltage factory wiring Class 2 low voltage field wiring M1 A1 T1 R1 Field wiring remote control (see notes 3, 4) 120V, 60Hz W1 F1 J5 J7 J6 J4 ELECTRONIC ASSEMBLY 123 1 2 1 2 123 1 2 3 4 1 2 1 2 3 4 5 1 2 3 4 5 J8 J9 J11 J10 1 2 J12 J13 J1...

13 120V, 60Hz Neutral 120V, 60Hz Line CPU K2 K4 K5 J5-2 J10-1 J10-2 Exhaust fan motor Supply fan motor J5-1 J5-3 J7-2 J7-1 J4-1 J4-3 J6-2 J6-1 K1 K3 K2 J9-1 J9-2 J9-3 J4-2 J9-4 Exhaust fan motor capacitor Supply fan motor capacitor J8-1 J8-2 J8-4 J8-5 K4 J12-2 J12-1 A1 A2 Damper motor J3-2 J3-1 J2-2...