Carrier 58MSA- Manuals

6 Dimensions A98307 DIMENSIONS (In.) UNIT SIZE A D E 040-08 17-1/2 15-7/8 16 040-12 17-1/2 15-7/8 16 060-08 17-1/2 15-7/8 16 060-12 17-1/2 15-7/8 16 060-16 17-1/2 15-7/8 16 080-12 17-1/2 15-7/8 16 080-16 17-1/2 15-7/8 16 080-20 21 19-3/8 19-1/2 100-16 21 19-3/8 19-1/2 100-20 21 19-3/8 19-1/2 120-20 ...

7 1 ⁄ 2 OD INDUCER HOUSINGDRAIN CONNECTION 1 ⁄ 4 OD COLLECTOR BOX TOTRAP RELIEF PORT 5 ⁄ 8 OD COLLECTOR BOXDRAIN CONNECTION 1 ⁄ 2 -IN. PVC OR CPVC SCREW HOLE FORUPFLOW OR DOWN-FLOW APPLICATIONS(OPTIONAL) 1 4 2 7 8 1 8 7 SLOT FOR SCREW HORIZONTAL APPLICATION (OPTIONAL) WIRE TIEGUIDES(WHEN USED) 1 2 1...

8 Performance data PSC — Permanent Split Capacitor EFFICIENCY * Capacity and AFUE in accordance with U.S. Government DOE test procedures.ICS — Isolated Combustion System AIR DELIVERY — CFM (With Filter)* *Air delivery above 1800 CFM requires that both sides, a combination of 1 side and bottom, or bo...

10 Vent piping MAXIMUM ALLOWABLE VENT PIPE (1 PIPE SYSTEM) LENGTH (FT) See notes on pg. 11. ALTITUDE ABOVE SEA LEVEL (FT) UNIT SIZE VENT PIPE DIA (IN.) NUMBER OF 90° ELBOWS 1 2 3 4 5 6 0 to 2000 040-08040-12 1 5 NA NA NA NA NA 1-1/2 70 70 65 60 60 55 2 70 70 70 70 70 70 060-08060-12060-16 1-1/2 20 1...

13 Clearance to combustibles A97609 323857-101 REV. C (LIT) MINIMUM INCHES CLEARANCE TO COMBUSTIBLE CONSTRUCTION * Mimimum front clearance for service 30 inches (762mm). 140 size furnaces require 1 inch back clearance to combustible materials. For installation on combustible floors only when install...

14 A96203 A/C COIL OUTDOOR UNIT VENT PIPE HUMIDIFIER GAS-FIREDWATER HEATER ELECTRONICAIR CLEANER AIRFLOW AIR IN COMBUSTION- AIR INLET A96202 Typical installations ELECTRONIC AIR CLEANER HUMIDIFIER A/C COIL VENT OUTDOORUNIT AIRFLOW COMBUSTION-AIR INLET Basement — Upflow Application Closet — Downflow ...

Carrier Corporation • Syracuse, New York 13221 6-98 Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book 1 4 Page 16 Catalog No. 525-817 Printed in U.S.A. PC 101 Form 58MSA-2PD Tab 6a 8a Replaces: 58MS...

Never use matches, candles, flame, or other sources ofignition to check for gas leakage. Use a soap-and-watersolution. Failure to follow this warning could result in a fire,personal injury, or death. 19. Replace main furnace door. Step 4—Cleaning Heat Exchangers The following items should be perform...

Never use matches, candles, flame, or other sources ofignition to check for gas leakage. Use a soap-and-watersolution. Failure to follow this warning could result in a fire,personal injury, or death. 18. Replace main furnace door. SECONDARY HEAT EXCHANGERS NOTE: The condensing side (inside) of the s...

4. Disconnect pressure switch tubes. 5. Disconnect vent pipe from inducer housing outlet by loosen- ing coupling clamp on inducer outlet. 6. Disconnect drain tube from inducer housing. (See Fig. 8.) 7. Remove inducer housing assembly by removing 4 bolts attaching assembly to cell panel. 8. Flush ins...

4. BRIEFLY remove either wire from the main limit switch until the LED goes out, then reconnect it. Make sure limit switch wire does not contact any metalliccomponent such as the gas valve. If wire is shorted, 3-ampfuse on control center will blow. NOTE: If wire to main limit is disconnected longer ...

1. Check for signs of physical damage to heat tape such as nicks, cuts, abrasions, gnawing by animals, etc. 2. Check for discolored heat tape insulation. If any damage or discolored insulation is evident, replace heat tape. 3. Check that heat tape power supply circuit is on. Step 10—Winterizing Free...

PCB BLOWER OFF DELAY SELECTION CHART 90 SEC 135 SEC 180 SEC 225 SEC GVR HI/LO RELAY SEC-1 SEC-2 WHT PL1 3 2 1 6 5 49 8 7 LED TEST/TWIN BLOWER OFF DELAY GR YW C HUM HSIR IDR BLWR BLOWER SPEED SELECT FU1 COOL HEAT L2 PL3 PL2 VAC 120 L1 PR1 1 2 123 PR2 24 VAC-3A FUSE SPARE-2 SPARE-1 EAC-1 EAC-2 C 1. 5 ...

→ Fig. 16—Service Label A99107 SERVICE COMPONENT TEST To initiate the component test sequence,shut OFF the room thermostat ordisconnect the "R" thermostat lead. Briefly short the TEST terminal to the "Com24V" terminal. Status LED will flash code and then turn ON the inducer motor. Th...

A94328 SERVICE TRAINING Packaged Service Training programs are an excellent way to increase your knowledge of the equipment discussed in this manual, including: • Unit Familiarization • Maintenance • Installation Overview • Operating Sequence A large selection of product, theory, and skills programs...