Carrier 52C- Manuals

Carrier 52C– User Manual, Manual in PDF format online.

Manuals:

User Manual Carrier 52C

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36

Summary

Page 2 - FRONT PANEL; FIGURE 1 — SAMPLE DATA INFORMATION PLATE

2 GENERAL Thank you for choosing Carrier! You can feel confident in your selection because the same pride in craftsman-ship and engineering knowledge that goes into Carrier equipment at the Astrodome in Texas, the Sistine Chapel in Rome, the US Capitol Hall of Congress, and thousands of other instal...

Page 3 - FIGURE 3 — MODEL NUMBER NOMENCLATURE; FIGURE 4 — FRONT PANEL INSTALLATION

3 To install the front panel, follow the procedure out-lined below:Replace the unit front panel. 1. Hold the front panel firmly at the center top and center bottom at a 5 to 10 degree angle from vertical. 2. Place the top of the front panel onto the unit mak- ing sure the top engagement posts have e...

Page 4 - ELECTRICAL DATA; ALL UNITS; WIRE SIZE —; Use recommended wire size given in; GROUNDING; — For safety and protection, the; TABLE 1 — SUGGESTED BRANCH CIRCUIT; VOLTAGE SUPPLY; POWER CORD PROTECTION; — The power cord; TABLE 2 — RECEPTACLES AND FUSE TYPES — 250,265 VOLTS; ELECTRICAL SHOCK HAZARD

4 ELECTRICAL DATA Be sure that your outlet matches the appropriate blade configuration of the supplied plug and that it is within reach of the service cord. A hardwire kit is available as an accessory to change cord-connected units to hardwired units. (See Accessories table on page 15.) ALL UNITS ■ ...

Manual Carrier 52C

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52

Summary

Page 2 - SERIES; INTRODUCTION; FIGURE 1 — SAMPLE DATA INFORMATION

52C,P SERIES 2 INTRODUCTION The focus of this manual is to provide basic information on service procedures, safety, troubleshooting, clean-ing, and component replacement for service techni-cians. It is intended for use only by HVAC service technicians who have successfully completed instruction and ...

Page 3 - UNIT DISASSEMBLY; TOOLS NEEDED; FIGURE 2 — MODEL NUMBER NOMENCLATURE

3 UNIT DISASSEMBLY This section includes common procedures for disas-sembly and re-assembly of unit. TOOLS NEEDED The following field-supplied items are recommended for general disassembly of the unit:• Flat head screw driver• 5 / 16 -in. nut driver • Safety glasses• Needle nose pliers REMOVE FRONT ...

Page 4 - OPEN THE CONTROL BOX; Remove the four mounting screws that secure the; FIGURE 5 — PLUG ASSEMBLY ON; PECIFIED ON THE PRODUCT.

52C,P SERIES 4 OPEN THE CONTROL BOX The control box is factory wired. To open the box, remove the 2 screws on the top of the control box and lower the front hinged panel. See Figure 6. REMOVE THE UNIT FROM THE WALL SLEEVE 1. Remove the four mounting screws that secure the PTAC unit to the wall sleev...

Carrier Manuals