Carrier 40RMQ- Manuals

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 5 1.0 Executive Summary RHT Energy Solutions (RHT) was contracted by the City of Ashland to perform energy audits on its municipal facilities. On February 27, 2013, Buzz Thielemann and Rick Reichert of RHT conducted an energy scopin...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 9 3.0 Energy Efficiency Measures Following are the capital energy efficiency measures that were identified. Note that several low cost/no cost measures were also identified (see Section 1.4), as were two capital improvements that we...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 11 To further conserve energy and reduce annual energy costs, a City-wide policy should be established to turn off all desktop computer monitors before leaving the building. Power management software is available from several vendor...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 12 Low cost/no cost Recommendation 1: Establish new City portable heater policy: A City policy on the use of portable heaters should be established immediately, and the use of all existing portable heaters should be stopped immediat...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 13 Because there is a wide variance in thermal comfort with all people, a wise choice would be to require the use of radiant flat-panel vanity/desk heaters with input power of 200-400 Watts each. Experience has shown that the smalle...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 14 Low Cost/No Cost Recommendation 3: Install occupancy sensors or simple mechanical timers to restroom lighting: This will ensure that non-priority lights do not remain on when not in use. Be sure to use program-start ballasts (not...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 15 #1: Add R12 insulation to areas of the exterior walls that are inadequately insulated . With the exception of the relatively new addition in the corner of the 2 nd story, City Hall walls are inadequately insulated. This table sho...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 17 9.0 General Facility Data Operating hours: Typically 7am to 6pm, Monday – Friday with occasional evening usage of meeting rooms. Domestic hot water: An instant water heater was observed under the sink on the 2 nd floor break room...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 18 Roofing: Membrane over 3-inch foam insulation (estimated). Exterior Lighting: Assumed to be high-pressure sodium (HPS) on daylight sensor control. Electric meter number: 14292 Natural Gas meter number: 123710 (serves the back-up ...

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 19 10.0 Additional pictures 1.5 Ton Heat Pump on Roof Two 4 Ton Heat Pumps on roof Stationary Heat Pump Condenser Fan Heat Pump #4 on shed roof (Large air handler is inside shed)

City Hall 20 E. Main St., Ashland, Oregon RHT Energy Solutions Page 20 Stand ‐ by   generators  

Energy Data - City Hall - Electricity Only Meter #: 14292 / 01 720 643 Months 24 Converted to kBTU 375,430 Square Feet 8,443 Average Annual EUI 44.466 Start Date End Date Days in Period kWh $ Avg $/kWh 10/08/2012 11/07/2012 30 7,640 563.43 $ 0.0737 09/10/2012 10/08/2012 28 7,240 539.84 $ 0.0746 08/0...

Replace single-paned windows at City Hall Estimated Project Cost: $34,000 City Hall baseline electricity usage per year: 110,000 kWh Estimated % energy savings: 5% Estimated annual energy savings: 5,500 kWh City Hall electricity cost / kWh: $0.0678 Estimated annual cost savings: $373 Simple Payback:...

Copyright 2001 Carrier Corporation Form 38AQS-5PD Heat Pump Heat Pump Systems that SaveEnergy and Provide Outstanding Heating and Cooling All Year• All-season comfort in any climate• High energy savings capability• Suitable for new construction or replacement Features/Benefits System indoor and outd...

2 surrounding air (even outside air at ex-tremely cold temperatures), and ends with the indoor coil releasing or reject-ing heat to the air around it. Variable refrigeration circuit-ing (VRC) — 38AQS units For that extra measure of heat pump performance, variable refrigeration cir-cuiting provides i...

3 Easy installation and service — The 40RMQ multiposition designand component layout help you to get the unit installed and running quickly. The direct-expansion (DX) coils have factory-installed thermostatic expan-sion valves (TXVs) with matching dis-tributor nozzles. All 40RMQ units also include f...

4 Model number nomenclature 38AQS 008 – – – 5 0 1 – – 38AQS — Split System Heat Pump – – — Not Used Nominal Tons Packaging 008 — 7-1/2 Tons 0 — Base Unit 012 — 10 Tons 1 — Domestic 016 — 15 Tons Revision Number – – — Not Used 0 — Original – — Aluminum (Standard) 1 — 575-3-60 (Sizes 012,016 Only) C —...

Single-package standard efficiencyrooftop heat pumps with: • State-of-the-art defrost system • Dependable 4-way valve operation • Refrigerant filter strainer and accumulator • Field-installed electric heaters available • Advanced hermetic compressors mounted on vibration isolators • Factory-installe...

ARI* capacity ratings UNIT 50TJQ NOMINAL TONS STANDARD CFM COOLING HEATING (High Temp) SOUND RATING (Bels) Capacity (Btuh) SEER† Capacity (Btuh) HSPF Belt Drive Direct Drive 004 3 1200 35,600 10.20 10.00 34,400 6.7 8.4 005 4 1600 46,500 10.00 9.70 46,500 7.0 8.0 006 5 2000 57,000 10.00 9.90 57,000 7...

MODEL PH1010 SEER 3 PHASE HEAT PUMP UNITSIZES 048, 060 — 4 AND 5 NOMINAL TONS Product Data FEATURES AVAILABLE Nominal sizes are available in 048 and 060 sizesto meet the needs of light commercial applications. EFFICIENCY: With SEER of at least 10.0 and HSPF of 7.0, theseheat pump systems provide eco...

—3— PH10 SPECIFICATIONS * The ampacity of non-metallic (NM) sheathed cable shall be that of 60°C (140 ˚ F) conductors per NEC 1999, Article 336-26. If wire used is other than specified in chart, refer to applicable tables available in 1999 NEC. Copper wire must be used from disconnect to unit. † Len...

—4— PH10 REFRIGERANT METERING DEVICE AND LINE SET DATA * Piston listed is for any approved coil combination. † Charging subcooling for indoor TXV-type expansion device. . OPTIONAL EQUIPMENT USAGE GUIDELINE * For tubing line sets between 80 and 200 ft (250 ft total equivalent length), refer to the Re...

—6— PH10 COMBINATION RATINGS * Outdoor section/indoor section combination tested in accordance with DOE test procedures for heat pumps. Ratings for other combinations are determined under DOE computer simulation procedures. † In most cases, only 1 method should be used to achieve TDR function. Using...

—7— PH10 DETAILED COOLING CAPACITIES* See notes on page 8. EVAP AIR CONDENSER ENTERING AIR TEMPERATURES °F 85 95 105 115 CFM EWB Capacity MBtuh† Total Sys kW** Capacity MBtuh† Total Sys kW** Capacity MBtuh† Total Sys kW** Capacity MBtuh† Total Sys kW** Total Sens‡ Total Sens‡ Total Sens‡ Total Sens‡...

—8— PH10 DETAILED COOLING CAPACITIES* Continued EVAP AIR CONDENSER ENTERING AIR TEMPERATURES °F 85 95 105 115 CFM EWB Capacity MBtuh† Total Sys kW** Capacity MBtuh† Total Sys kW** Capacity MBtuh† Total Sys kW** Capacity MBtuh† Total Sys kW** Total Sens‡ Total Sens‡ Total Sens‡ Total Sens‡ PH10PR060-...

—9— PH10 HEAT PUMP HEATING PERFORMANCE See notes on page 10. INDOOR AIR OUTDOOR COIL ENTERING AIR TEMPERATURES °F –3 7 17 27 37 47 57 67 EDB CFM Capacity MBtuh† Total Pwr Capacity MBtuh† Total Pwr Capacity MBtuh† Total Pwr Capacity MBtuh† Total Pwr Capacity MBtuh† Total Pwr Capacity MBtuh† Total Pwr...

— 10 — © Payne Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231 Printed in U.S.A. edition date: 3/06 Catalog No. SS-PH10-09 Manufacturer reserves the right to change, at any time, specifications or designs without notice and obligations Replaces: SS-PH10-08 HEAT PUMP HEATING P...

Table 1D — 40RM Physical Data, SI UNIT 40RM 007 008 012 014 016 024 028 034 NOMINAL CAPACITY (kW) 21 26 35 43 52 70 87 105 OPERATING WEIGHT (kg) Base Unit with TXV 173 175 184 304 311 313 463 467 Plenum 44 44 44 63 63 63 82 82 FANS Qty...Diam. (mm) 1...381 1...381 1...381 2...381 2...381 2...381 2.....

Table 1E — 40RMQ Physical Data, SI UNIT 40RMQ 008 012 016 NOMINAL CAPACITY (kW) 26 35 52 OPERATING WEIGHT (kg) Base Unit with TXV 175 194 323 Plenum 44 44 63 FANS Qty...Diam. (mm) 1...381 1...381 2...381 Nominal Airflow (L/s) 1604 1888 2831 Airflow Range (L/s) 1203-2006 1416-2360 2124-3539 Nominal M...

Table 1F — 40RMS Physical Data, SI UNIT 40RMS 008 010 012 014 016 024 028 034 NOMINAL CAPACITY (kW) 26 29 35 43 52 70 87 105 OPERATING WEIGHT (kg) Base Unit 177 177 177 300 307 310 469 473 Plenum 44 44 44 63 63 63 82 82 FANS Qty...Diam. (mm) 1...381 1...381 1...381 2...381 2...381 2...381 2...457 2....

TXV — Thermostatic Expansion ValveNOTES:1. Dimensions in [ ] are in millimeters. 2. Direction of airflow. 3. Recommended clearance: • Rear: 3 in. (76 mm )• Front: 2 ft, 6 in. (762 mm)• Right Side: 2 ft, 6 in. (762 mm)• Left Side: 2 ft, 6 in. (762 mm)• Local codes or jurisdiction may prevail. 4. Liqu...

Unit Positioning — The unit can be mounted on the floor for vertical application with return air entering the faceof the unit and supply air discharging vertically through thetop of the unit. The unit can also be applied in a horizontalarrangement with return air entering horizontally and the sup-pl...

Unit Isolation — Where extremely quiet operation is essential, install isolators between floor and base of unit, orbetween ceiling and top section of unit. Be sure that unit is level and adequately supported. Use channels at front and sides of unit for reference points whenleveling. Refrigerant and ...

IMPORTANT: Never attach the sensor to the suctionmanifold. Do NOT mount the sensor on a trapped por-tion of the suction line. 40RM Series evaporator coils have a face-split design. En- sure that lower circuit of coil is first on/last off when con-nected to the condensing unit and/or system controls....

Table 2 — Factory-Installed Nozzle and Distributor Data UNIT TXV Qty...Part No. DISTRIBUTOR Qty...Part No. FEEDER TUBES PER DISTRIBUTOR* Qty...Size (in.) NOZZLE Qty...Part No. 40RM007 1...XVE-5 1...1116 12 1...E5 40RM008 1...SVE-8 1...1126 15 1...C6 40RMQ008 1...SVE-8 1...1657 15 1...C6 40RM012 2......

Table 3 — Fitting Requirements UNIT ACCESS HOLE NO.* CONNECTION TYPE CIRCUIT FITTINGS REQUIRED† (in.) 40RM 007 1 Suction — 1 1 ⁄ 8 Street Elbow 1 1 ⁄ 8 Nipple, 10 5 ⁄ 8 L 1 1 ⁄ 8 Long Radius Elbow 3 Liquid — 5 ⁄ 8 Street Elbow 5 ⁄ 8 Nipple, 8 5 ⁄ 8 L 5 ⁄ 8 Long Radius Elbow 40RM 40RMQ 008 1 Suction ...

Table 3 — Fitting Requirements (cont) UNIT ACCESS HOLE NO.* CONNECTION TYPE CIRCUIT FITTINGS REQUIRED† (in.) 40RMS 028, 034 5 Supply Lower 2 1 ⁄ 8 Long Radius Elbow 2 1 ⁄ 8 Nipple, 3 1 ⁄ 2 L 2 1 ⁄ 8 Long Radius Elbow 6 Return Lower 2 1 ⁄ 8 Long Radius Elbow 2 1 ⁄ 8 Nipple, 3 L 2 1 ⁄ 8 Long Radius El...

Condensate Drain — Install a trapped condensate drain line to unit connection as shown in Fig. 10. The unit drainconnection is a PVC stub. See Fig. 11. Some areas may re-quire an adapter to connect to either galvanized steel orcopper pipe. For these applications, install a field-suppliedthreaded PVC...

Power Supply and Wiring — Check the unit data plate to ensure that available power supply matches electri-cal characteristics of the unit. Provide a disconnect switch ofsize required to provide adequate fan motor starting current.See Tables 4 - 6 for unit electrical data. Install disconnect switch a...

Table 4 — Electrical Data, Standard Motors UNIT V*-PH-HZ VOLTAGE LIMITS FAN MOTOR POWER SUPPLY Hp FLA Minimum Circuit Amps MOCP 40RM 007 208/230-1-60 187-253 1.3 7.6 9.5 15 208/230-3-60 187-253 2.4 5.8 7.3 15 460-3-60 414-528 2.4 2.6 3.3 15 575-3-60 518-632 1.0 1.35 1.7 15 230-3-50 207-253 2.4 5.8 7...

Table 5 — Electrical Data, Alternate Motors UNIT V*-PH-HZ VOLTAGE LIMITS FAN MOTOR POWER SUPPLY Hp FLA Minimum Circuit Amps MOCP 40RM 007 208/230-1-60 187-253 2.4 11.0 13.8 20 208/230-3-60 187-253 2.9 7.5 9.4 15 460-3-60 414-528 2.9 3.4 4.3 15 575-3-60 518-632 2.0 2.4 3.0 15 40RM 40RMQ 40RMS 008 208...

Table 6 — Fan Contactor Coil Data UNIT 40RM, 40RMQ 40RMS VOLTAGE (vac) MAXIMUM HOLDING VA 007-034 24 10 Connecting Ductwork — Refer to the Carrier Sys- tem Design Manual for the recommended design and layoutof ductwork. Figure 15 shows recommended duct connec-tion to units with 2 fans.DISCHARGE CONN...

START-UP Before starting unit, check the following and correct as necessary:• Is unit solidly supported?• Is fan adjusted for speed and pulley alignment?• Are pulleys, motor, and bearings securely mounted?• Are there any loose parts that will rattle or vibrate?• Is condensate drain pan pitched for c...

Centering Fan Wheel — If fan and fan shaft assem- bly are not properly centered, blades may scrape against scrollor may create an objectionable whistling noise. It may benecessary to adjust individual fan wheels or move entire fanshaft. See the following two sections. Fan Shaft Position Adjustment —...

Legend and Notes for Table 10A and 10B LEGEND Bhp — Brake Horsepower Input to FanESP — External Static Pressure NOTES:1. Maximum allowable fan speed is 1100 rpm for unit sizes 028 and 034; 1200 rpm for all other sizes. 2. Fan performance is based on deductions for wet coil, clean 2-in. filters, and ...

Table 10C — Fan Performance Data — 0-300 Pa ESP — SI UNIT AIRFLOW (L/s) EXTERNAL STATIC PRESSURE (Pa) 0 50 100 150 200 250 300 r/s kW r/s kW r/s kW r/s kW r/s kW r/s kW r/s kW 40RM 007 850 5.34 0.17 7.38 0.25 8.91 0.32 10.20 0.39 11.30 0.46 12.30 0.53 13.30 0.60 1000 6.28 0.24 8.10 0.32 9.53 0.40 10...

Table 10D — Fan Performance Data — 350-600 Pa ESP — SI UNIT AIRFLOW (L/s) EXTERNAL STATIC PRESSURE (Pa) 350 400 450 500 550 600 r/s kW r/s kW r/s kW r/s kW r/s kW r/s kW 40RM 007 850 14.10 0.67 15.00 0.74 15.70 0.81 16.50 0.87 17.20 0.94 — — 1000 14.60 0.77 15.40 0.84 16.10 0.91 16.90 0.98 17.60 1.0...

Legend and Notes for Tables 10C and 10D LEGEND ESP — External Static Pressure NOTES:1. Maximum allowable fan speed is 18.3 r/s for unit sizes 028 and 034; 20 r/s for all other sizes. 2. Fan performance is based on deductions for wet coil, clean 51-mm filters, and unit casing. See right for factory-s...

START-UP CHECKLIST (SPLIT SYSTEMS WITH 40RM/RMQ/RMS UNITS) A. Preliminary Information OUTDOOR: MODEL NO. SERIAL NO. INDOOR: MODEL NO. SERIAL NO. ADDITIONAL ACCESSORIES B. Pre-Start-Up OUTDOOR UNIT IS THERE ANY SHIPPING DAMAGE? (Y/N) IF SO, WHERE: WILL THIS DAMAGE PREVENT UNIT START-UP? (Y/N) CHECK P...

CHECK VOLTAGE IMBALANCE LINE-TO-LINE VOLTS: AB V AC V BC V (AB + AC + BC)/3 = AVERAGE VOLTAGE = V MAXIMUM DEVIATION FROM AVERAGE VOLTAGE = V VOLTAGE IMBALANCE = 100 X (MAX DEVIATION)/(AVERAGE VOLTAGE) = % IF OVER 2% VOLTAGE IMBALANCE, DO NOT ATTEMPT TO START SYSTEM! CALL LOCAL POWER COMPANY FOR ASSI...