Cabletron Systems 9F310-02 - Manuals

Page 3 - Notice

i Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or soft...

Page 4 - FCC Notice

ii Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOT...

Page 5 - Safety Information; CLASS 1 LASER TRANSCEIVERS

v Notice Safety Information CLASS 1 LASER TRANSCEIVERS The 9F315-02 is a Class 1 Laser Product The 9F315-02 uses Class 1 Laser transceivers. Read the following safety information before installing or operating these adapters. The Class 1 laser transceivers use an optical feedback loop to maintain Cl...

Page 7 - Contents

vii Contents Chapter 1 Introduction Features........................................................................................................................... 1-1Related Manuals ............................................................................................................ 1-4G...

Page 9 - Chapter 1; Introduction; Features

1-1 Chapter 1 Introduction The 9F310-02 and 9F315-02 are three port switch modules with two front panel FDDI interfaces and one INB-1 backplane interface. The external FDDI networks are connected to the modules using standard FDDI A/B ports on the front panel. The 9F310-02 uses multi mode fiber, and...

Page 12 - Related Manuals

Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual. MMAC-Plus Installation Guide MMAC-Plus Operations Guide MMAC-Plus 9C300-1 Environmental Module User ’s Guide MMAC-Plus 9C214-1 AC Power Supply User ’s Gu...

Page 13 - Chapter 2; Installing the MMAC-Plus modules

2-1 Chapter 2 Installing the MMAC-Plus modules The 9F310-02 and 9F315-02 modules occupy two slots in the MMAC-Plus chassis. The modules must be installed with the left side (as viewed from the front) in an odd numbered slot, and the right side in an even numbered slot. To install the 9F310-02 and 9F...

Page 15 - The Reset Switch

2-3 The Reset Switch The Reset Switch The Reset switch is located on the rightmost front panel, under the top plastic tab as shown in Figure 2-2. It serves two functions: • Pressing the reset switch twice within three seconds causes the processor (i960) to reset. • Pressing and holding the switch on...

Page 16 - User Accessible Components

Installing the MMAC-Plus modules 2-4 User Accessible Components Figure 2-3 shows the various components that are accessible to the user. These consist of an eight position dip switch (explained below), replaceable PROMs and sockets for RAM. These will be used for future upgrades. Instructions for in...

Page 19 - Chapter 3; Operation

3-1 Chapter 3 Operation The 9F310-02 and 9F315-02 modules are capable of bridging/switching any three, of five possible interfaces, depending on how it is configured. The INB-1 connection is always fixed. When configuring the module, the decision is made to connect both front panel ports, both FNB p...

Page 20 - System Management Buses

Operation 3-2 System Management Buses There are two management channels within the MMAC-Plus system: the SMB-1 and the SMB-10. These buses provide out-of-band management and inter-module management communication. SMB-1 Bus The SMB-1 is a 1Mbs management bus located within the MMAC-Plus. This bus is ...

Page 23 - Chapter 4

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in trouble shooting. Shown in Figure 4-1 is the LANVIEW LEDs of the 9F310-02 and 9F315-02 module. Figure 4-1. The LANVIEW LEDs A FDDI 1 2 INB 1 2 SMB CPU INB Transmit FDDI Status INB R...

Page 27 - Chapter 5; Specifications; Technical Specifications

5-1 Chapter 5 Specifications Technical Specifications CPU: Intel i960 RISC based microprocessor Memory: 4 Meg. Local RAM (expandable to 12 Meg.)2 Meg. Flash Memory (expandable to 16 Meg.)2 Meg. Packet RAM Standards: ANSI FDDI X3T9.5SMTMACPHYMMF-PMDSMF-PMD Network Interfaces: A/B ports MMF Connectors

Page 28 - Safety

Specifications 5-2 Safety This equipment meets the safety requirements of: • UL 1950 • CSA C22.2 No. 950 • EN 60950 • IEC 950 • EMI Requirements of FCC Part 15 Class A • EN 55022 Class A • VCCI Class I • EMC requirements of: EN 50082-1IEC 801-2 ESDIEC 801-3 Radiated susceptibilityIEC 801-4 EFT Servi...

Page 29 - Link Distance

5-3 Link Distance 9F310-02 Up to 2 kilometers on multimode fiber-optic cable as specified by ANSI MMF-PMD. 9F315-02 40 kilometers (max), 25 kilometer (typical) on single-mode fiber-optic cable as specified by ANSI SMF-PMD.