Cabletron Systems 9A656-04 ATM Module - Manuals

v Contents Chapter 1 Introduction Document Objectives.................................................................................................... 1-1Overview ........................................................................................................................ 1-2Features.....

Contents vi Chapter 4 LANVIEW LEDs ANIM LEDs ............................................................................................................ 4-3 Chapter 5 General Specifications Operating SpeciÞcations ........................................................................................

1-1 Chapter 1 Introduction Document Objectives This document, the SmartSwitch 9500 9A656-04 ATM Module Hardware and Installation Guide , contains introductory, installation and speciÞcation information for the support of the 9A656-04 SmartSwitch Module. Use this guide to learn about the following to...

Introduction 1-2 Overview The 9A656-04 (shown in Figure 1-1) is a 4.5 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four ATM Network Interface Modules (ANIMs) of any type can be plugged into the 9A656-04 to provide front panel connectivity to the network. Cabletron Systems ANIMs c...

Introduction 1-4 Features The features of the 9A656-04 are described in the sections below: Processor The 9A656-04 is equipped with an advanced Intel i960 microprocessor. This microprocessor provides signalling, SNMP management, and serves as the in-band management LAN Emulation Client (LEC). Cablet...

1-5 Related Manuals LANVIEW LEDs The 9A656-04 uses LANVIEW, The Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance. Related Manuals The manuals listed below should be used to s...

Introduction 1-6 Getting Help For additional support related to this device or document, contact the Cabletron Systems Global Call Center: Before calling the Cabletron Systems Global Call Center, have the following information ready: • Your Cabletron Systems service contract number • A description o...

2-1 Chapter 2 Installing the 9A656-04 Module SmartSwitch 9500 modules can be installed in any of the slots that are available. To install a module, proceed as follows: 1. Remove the blank plate covering the slot in which the 9A656-04 will be installed. All other slots must remain covered to ensure p...

2-3 The Reset Switch The Reset Switch The Reset switch is located on the front panel, under the top plastic tab as shown in Figure 2-2. It serves two functions: ¥ Pressing the Reset switch twice within three seconds causes the processor (i960) to reset. ¥ Pressing and holding the switch on for three...

Installing the 9A656-04 Module 2-4 The Module Card DIP Switch An eight position DIP switch is located on the module card as shown in Figure 2-3. The functions of the switches are listed in Table 2-1. ! CAUTION Do not toggle Switch 8 unless you intend to reset the user configured passwords to their f...

2-5 Installing an ANIM Installing an ANIM Figure 2-3 shows the location of the 4 motherboard connectors, and the 16 standoff screws for the ATM Network Interface Modules (ANIMs). Figure 2-3 also shows the location of the Module Card DIP Switch. Figure 2-3. ANIM Connector Locations and Module DIP Swi...

3-1 Chapter 3 Operation The 9A656-04 provides switching between the front panel interfaces (ANIMs) and the Cell Transfer Matrix backplane located inside the SmartSwitch 9500 chassis. Figure 3-1 shows the trafÞc ßow of ATM cells in the 9A656-04. The following sections brießy describe the functions of...

Operation 3-2 ATM Cell Traffic Flow in the 9A656-04 The 9A656-04 SmartSwitch utilizes several innovative features that result in a completely redundant, fault-tolerant design. The three most important hardware facets of the 9A656-04 SmartSwitchÕs features are the Cell Transfer Matrix, Cabletron Syst...

Operation 3-4 System Management Buses There are two management channels within the SmartSwitch 9500 system: ¥ SMB-1 ¥ SMB-10 These buses provide out-of-band management and inter-module management communication. SMB-1 Bus The SMB-1 is a 1 Mbps management bus located within the SmartSwitch 9500 chassi...

3-5 System Diagnostic Controller System Diagnostic Controller This diagnostic controller is composed of a Z-80 microprocessor and its supporting logic. The diagnostic controller performs the following: ¥ Controls the power-up sequencing of modules ¥ Monitors the 9A656-04 input and output power param...

4-3 ANIM LEDs The front panel LANVIEW LEDs indicate the status of the ANIM and may be used as an aid in troubleshooting. Shown in Figure 4-2 are the LANVIEW LEDs of all ANIMs. Although there are several types of ANIMs, all share the same LANVIEW LEDs. Refer to Table 4-2 for the full deÞnitions of AN...

5-1 Chapter 5 General Specifications The speciÞcations for the 9A656-04 are detailed in the sections that follow. Operating Specifications Environmental Requirements Operating Temperature 5¡C to 40¡C (41¡F to 104¡F) Storage Temperature: -30¡C to 73¡C (-22¡F to 164¡F) Operating Relative Humidity: 5% ...

General Specifications 5-2 Physical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters(13.8 D x 17.4 H x 1.2 W inches) Weight Unit: 1.36 kg. (3lb)Shipping: 1.81 kg. (4lb) Device Specifications Processor Intel i960HD RISC processor control Dynamic Random Access Memory (DRAM) 96 MB FLASH Memory 8 MB ANIM ...