Cabletron Systems 7C04 Workgroup - Manuals

v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ......................................................................... 1-11.2 USING THE SMARTSWITCH MANUAL SET ................................... 1-11.3 CHASSIS OVERVIEW .........................................................................

1-1 CHAPTER 1 INTRODUCTION Welcome to Cabletron Systems 7C04 Workgroup SmartSwitch Chassis User’s Guide . This manual describes the physical characteristics, specifications, and capabilities of the 7C04 Workgroup SmartSwitch Chassis. 1.1 USING THIS MANUAL Chapter 1, Introduction , discusses the feat...

1-2 Introduction 1.3 CHASSIS OVERVIEW The 7C04 Chassis (Figure 1-1) is a rack-mountable, multi-media, switching center. The chassis is a stand-alone device that features a removable power supply. Two fans within the power supply provide system cooling. LANVIEW LEDs on the power supply indicate at-a-...

Introduction 1-3 1.3.1 7X00 SmartSwitch Controller Module The 7X00 SmartSwitch Controller Module is the only processing and management element in the 7C04 Chassis. The 7X00 Module has no front panel data ports. All data enters and exits the 7X00 Module via the SmartSwitch Bus on the chassis’ backpla...

1-4 Introduction 1.3.3 Operations Data entering through a front panel of a SmartSwitch interface module in the 7C04 Chassis is converted by the module’s hardware into a common “canonical” format. Canonical frames are forwarded along the chassis’ SmartSwitch Bus to the 7X00 Module in slot one. The co...

1-6 Introduction 1.5 RELATED MANUALS The following manuals supplement the procedures and other technical data provided in this manual. The procedures will be referenced where appropriate, but will not be repeated. Cabletron Systems SmartSwitch Interface Module User’s Guides (module specific). Cablet...

2-2 Installation 2.2 INSTALLING THE 7C04 CHASSIS IN AN EQUIPMENT RACK The following section details the process of attaching mounting brackets to the 7C04 Chassis, and installing the chassis in a standard 19-inch equipment rack. If you are not installing the chassis in an equipment rack, skip to Sec...

Installation 2-3 7. Align the two round holes of the left mounting bracket with the holes (from which you removed the screws) on the left side of the chassis. 8. Insert the screws that you removed in step 6 into the holes on the bracket and chassis. Tighten the screws until the mounting bracket is s...

2-4 Installation 2.2.2 Mounting the 7C04 Chassis To mount the 7C04 Chassis in a standard 19-inch equipment rack, (Figure 2-2) use the following steps: 1. Slide the chassis into the equipment rack. 2. Align the holes on the chassis’ mounting brackets with the holes on the equipment rack. 3. Insert sc...

Installation 2-5 2.3 THE 7C04 CHASSIS POWER SUPPLY MODULE The 7C04 Chassis is equipped with a removable power supply module. The power supply module which is located in the right section of the chassis (Figure 2-2) operates on either 120 volts or 240 volts (AC) and automatically senses input power. ...

2-6 Installation 3. Align the notch on the top of the power supply module with the semi-circular tab in the top center of the power supply module cavity of the chassis. Figure 2-3. Installing the power supply module into a 7C04 Chassis 4. Slide the power supply module into the chassis until the powe...

Installation 2-7 2.3.3 Powering up the Power Supply Module Note: Prior to powering up the power supply module, we recommend that you install the 7X00 Module and SmartSwitch interface modules into the chassis. Refer to the applicable module’s user’s guide for installation instructions. To power up th...

2-8 Installation 2.3.4 Removing the Power Supply Module To remove the power supply module from the chassis, refer to Figure 2-4 and proceed as follows: 1. Press the power supply’s power switch to the off position (O). 2. Unplug the power cord from the power supply and from the electrical outlet. 3. ...

3-1 CHAPTER 3 TROUBLESHOOTING The front panel of the power supply module of the 7C04 Chassis (Figure 3-1) contains four LANVIEW LEDs to assist you in troubleshooting the power supply. The color of each LED and the course of action to pursue are detailed in Table 3-1 through Table 3-4. Note: For info...

Troubleshooting 3-3 Table 3-3. OVERLOAD LED LED Color Indicates Action Green Normal operation No action necessary. Red The modules within the chassis are attempting to draw an amount of DC power that exceeds the power supply’s maximum DC power output. Contact Cabletron Technical Support. Table 3-4. ...

4-1 CHAPTER 4 TECHNICAL SPECIFICATIONS This chapter includes the technical specifications for Cabletron Systems 7C04 Chassis. Cabletron Systems reserves the right to change these specifications at any time without notice. 4.1 SAFETY It is the responsibility of the person who sells the chassis to ens...

4-2 Technical Specifications 4.4 SERVICE MTBF: >200,000 hours MTTR: <0.5 hour 4.5 POWER AC Input: 100 - 125 volts, 3.8 amps 200 - 250 volts, 1.9 amps 50/60 Hz DC Output: 5.1 volts 12 volts Fusing: The input of the power supply contains a 250 volt (AC) minimum fuse to protect against internal d...