Page 2 - MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
2 BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) All coffee and tea dispensers/servers, MCR/MCP/MCA single cup brewers, and BUNNlink ® electronic circuit and/or control boards – 1 year parts and 1 year labor. 2) Product-specif...
Page 3 - INTRODUCTION; Recipe
3 This equipment will brew coffee into an awaiting Soft Heat (SH) Server. The brewer may have an auxiliary hot water faucet. It is only for indoor use on a sturdy and level counter or shelf. Please install in an area where there are no water jet devices. The Infusion Series, similar to the DBC BrewW...
Page 4 - NORTH AMERICAN REQUIREMENTS; • Appliance shall not be tilted more than 10° for safe operation.; CE REQUIREMENTS
4 • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 41°F to 95°F (5°C to 35°C). • Appliance shall not be tilted more than 10° for safe operation. • An electrician mu...
Page 5 - OPERATOR NOTICES; WARNING; S L O W LY; H O T; L I Q U I D; ELECTRICAL REQUIREMENTS; WARNING; - The power cord must be; determine circuit requirements.; DUAL VOLT
5 OPERATOR NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. #00656.0001 As directed in the International Plumbing Code of the International Code Council and the F...
Page 6 - NOTE; PLUMBING REQUIREMENTS; CAUTION; ) Select the desired unit voltage based on the; DV models only; ) Set voltage switch to the appropriate position and; EURO Plug
6 These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (0.138 and 0.620 mPa) from a 1/2˝ or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (0....
Page 7 - Tank Drain; NOTICE; a. Cold Brew Mode: Convert model for cold brewing using
7 Tank Drain 1. Loosen screws that secure the front access panel. Remove the panel.2. Tighten the white shutoff clamp on the long hose between the tank and inlet solenoid.3. Disconnect the hose clamp and hose from the inlet solenoid.4. Place the end of the drain hose in a container that has a minimu...
Page 8 - COFFEE BREWING
8 There may be certain situations in which the brew cycle will not begin when BREW is selected: a. BREW TEMPERATURE TOO LOW - wait until heated, or cancel BREW LOCKOUT option. b. CHECK FUNNEL - remove funnel, empty previously brewed grounds and replace with fresh. Brewing without a Smart Funnel and ...
Page 9 - Daily; NOT; Weekly; CLEANING
9 Daily 1. The intuitive Care and Cleaning instructions are accessible in the Programming section. Start from Home screen, then touch the BUNN logo for 2 seconds to enter the Service Access screen. 2. Select the Care and Cleaning icon to prompt the Care and Cleaning buttons.3. Select the "Clean ...
Page 10 - Home Screen; Touch the BUNN logo for 3 seconds to enter the programming.; C. BATCH SELECTOR SWITCHES; PROGRAMMING
10 M L S S M L BREW REGULAR BREW DECAF Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various brewing parameters such as brew temperatures, brew volumes, bypass, pulse brew, pre-infusion, SmartWAVE ® , drip time and fresh time. The operator ...
Page 11 - CALIBRATE FLOW; , and testing the brew and bypass valves in; Touch for 3 seconds; Programming Lockout
11 Always remember to place a container and funnel under the sprayhead when operating the brewer during the set-up of CALIBRATE FLOW , and testing the brew and bypass valves in SERVICE TOOLS / TEST OUTPUTS. M L S S M L BREW REGULAR BREW DECAF Touch for 3 seconds SERVICE RECIPES STATISTICS ADVANCED C...
Page 12 - certain components are activated.
12 Advanced Menu Options RECIPES - Select this icon to disable, enable, add or modifying recipes. MACHINE SETTINGS - Select this icon to adjust global settings on the brewer. SERVICE - Select this icon to access high level diagnostic functions and service information. CALIBRATIONS - Select this icon...
Page 13 - How To Calibrate Bypass Flow Rate; The 60-second timer on the display will count down to zero.
13 PROGRAMMING continued > How To Calibrate Bypass Flow Rate This function allows the operator to test and enter the actual flow rate of water coming out of the bypass. The procedure includes a 1-minute dispense of water to determine the actual flow rate. Ensure that the brewer is heated to brewi...
Page 14 - Renaming A Recipe; Enabling / Disabling Batch Sizes; navigate to the desired recipe name to edit. Select the recipe name.
14 PROGRAMMING continued > Renaming A Recipe There are 5 pages containing 6 recipe names (30 total). By default, recipe names are preset from the factory. The operator has the choice of renaming any recipe.1. Touch the BUNN logo for 3 seconds to enter SERVICE ACCESS. 2. Select the ADVANCED icon.3...
Page 15 - will exit them back to the recipe parameter screen.; Modifying Recipe
15 RECIPE EDIT VOLUME SMARTWAVE RECIPE REVIEW PULSE BREW PRE-INFUSE FRESHNESS DRIP TIME BYPASS SH TEMP PROGRAMMING continued > VOLUME - This icon allows for volume adjustments. Each batch size, small, medium, and large will have adjustable brew volume ranges to choose from. Pressing SAVE after th...
Page 16 - on and off times the brewer will use to make a pulse routine.
16 PULSE BREW - Pre-infusion and bypass settings will be taken into account if set already. The operator will use the text fields to enter times. When entering the sprayhead on time, the ounces or milliliters (depends on units set on the machine) being dispersed for that amount of time will display....
Page 17 - Machine Settings; Brew and Server Settings.; How To Access Machine Settings; programming button will navigate the user to the main home screen.; MACHINE
17 Machine Settings By default, machine settings are preset from the factory. The operator has the choice to modifying Regional, Brewer, Brew and Server Settings. How To Access Machine Settings 1. Touch the BUNN logo for 3 seconds to enter SERVICE ACCESS. 2. Select the ADVANCED icon.3. At the PASSWO...
Page 18 - Brew Settings; LOWEST RECIPE TEMP; Default Screen for Brew Settings
18 Brew Settings Accessed from MACHINE SETTINGS, there are several adjustable settings shown within the Brew Settings option. Brew Mode : COLD Brew Mode enables operators to craft a batch of concentrate or ready-to-drink cold brew quickly and consistently. When enabled, COLD Brew Mode uses a range f...
Page 19 - Enabling FRESHlink Server Settings
19 Enabling FRESHlink Server Settings 1. Touch the BUNN logo for 3 seconds to enter SERVICE ACCESS. 2. Select the ADVANCED icon.3. At the PASSWORD ENTRY screen, select ENTER (If a password is required, enter the code at this screen). 4. In the ADVANCED MENU screen, select MACHINE SETTINGS and then t...
Page 22 - Change Password; Passwords can be created or reset from this screen.
22 PROGRAMMING Change Password This feature allows the user to set passwords for different regions of the machine.1. Touch the BUNN logo for 3 seconds to enter SERVICE ACCESS. 2. Select ADVANCED.3. Select MACHINE SETTINGS.4. Select REGIONAL SETTINGS. 5. Select PASSWORD. 6. For this example select SC...
