Page 3 - INTRODUCTION; no water jet devices.; CONTENTS
Page 3 INTRODUCTION This equipment will brew coffee into an awaiting server or airpot. The brewer may have an auxillary hot water faucet. It is only for indoor use on a sturdy and level counter or shelf. Please install in an area where there are no water jet devices. The Infusion Series, similar to ...
Page 4 - USER NOTICES; kept in good condition. Replace any unreadable or damaged labels.; WARNING; HOT
Page 4 #00656.0001 As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models install...
Page 6 - An electrician must provide electrical service.; ELECTRICAL REQUIREMENTS; WARNING - The power cord must be; C, and the attachment plug cap must be UL Listed,; DUAL VOLT
Page 6 54212 051217 ELECTRICAL HOOK-UP (All Models) CAUTION – Improper electrical installation will damage electronic components. Damage caused by incor- rect electrical connections is not covered by warranty. 1. An electrician must provide electrical service. 2. Determine the available on-site elec...
Page 7 - TANK DRAIN; Disconnect the hose clamp and hose from inlet solenoid.; PLUMBING REQUIREMENTS; line by this type of device may restrict water flow.
Page 7 TANK DRAIN 1. Loosen screws that secure the front access panel. Remove the panel. 2. Tighten the white shutoff clamp on the long hose between tank and inlet solenoid. 2. Disconnect the hose clamp and hose from inlet solenoid. 3. Place the end of the drain hose in a container that has a minimu...
Page 8 - OPERATING CONTROLS; releasing this switch will begin a brew cycle on the selected side.; E. BATCH SELECTOR SWITCHES; NOTE –
Page 8 OPERATING CONTROLS A. ENABLE BREW ON/OFF SWITCH Pressing the "ENABLE BREW ON/OFF" switch (indicator on) enables the brew circuit (on that side of Twins), and energizes the tank refill circuit. Pressing the switch again (indicator off) stops tank refilling and brewing. Stop- ping a bre...
Page 9 - VIEWING ASSIGNED RECIPES, ASSET & SERIAL NUMBER; TANK FILLING until tank is filled with water.
Page 9 INITIAL SET-UP VIEWING ASSIGNED RECIPES, ASSET & SERIAL NUMBER 1. Make sure the "ENABLE BREW ON/OFF" switch is OFF (LED will not be lit). 2. Press and hold "BREW A" switch. The display will show the name of the recipe assigned to Brew A along with "SWITCH NOT ON". ...
Page 10 - COFFEE BREWING; WITHOUT A SMART FUNNEL AND MHG or DBC GRINDER:
Page 10 COFFEE BREWING WITHOUT A SMART FUNNEL AND MHG or DBC GRINDER: 1. Begin each brew cycle with a clean empty brew funnel. 2. Insert a BUNN filter into the funnel. 3. Pour the fresh coffee into the filter and level the bed of grounds by gently shaking. 4. Slide the funnel into the funnel rails o...
Page 11 - CLEANING; Remove sprayhead from brewer. Disassemble by removing the seal.
Page 11 CLEANING 1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 2. Check and clean each sprayhead. The sprayhead holes must always remain open. NOTE ...
Page 12 - PROGRAMMING; for the precise brewing of various flavors of tea and coffee.; PROGRAMMING SWITCHES
Page 12 PROGRAMMING Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various brewing parameters such as brew temperatures, brew volumes, dilution volumes, pulse brew, etc. This allows for the precise brewing of various flavors of tea and coffe...
Page 13 - For additional information, you; READY TO BREW
Page 13 MAIN SCREEN This screen will be shown when the brewer is ready for use. The screen displays the water temperature in the tank. When the water in the tank reaches the correct set temperature, the display will change from HEATING to READY TO BREW. PROGRAMMING LOCKOUT SWITCH is located on the m...
