Buhler 2895 - Manuals - manualsarea.com

Page 2 - WARRANTY REGISTRATION AND POLICY; Any labor subject to warranty; must; be authorized by Buhler Manufacturing. The labor; PRINTED IN CANADA

WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufactur...

Page 3 - bühler; Allied Front-End Loader; 895 OPERATOR’S AND PARTS MANUAL; Table of Contents

bühler Allied Front-End Loader - 1 - P4110 2895 OPERATOR’S AND PARTS MANUAL Table of Contents Description Page Registration and Policy Loader Specifications .......................................................................................... 2 Introduction Terminology ............................

Page 4 - LOADER SPECIFICATIONS

bühler Allied Front-End Loader - 2 - P4110 LOADER SPECIFICATIONS Illustration (TSL shown)

Page 6 - INTRODUCTION; tractor manual

bühler Allied Front-End Loader INTRODUCTION This manual has been provided as information regarding the specifications, safeoperation and maintenance of your agricultural front-end loader. Read and understandthis manual and the tractor manual prior to operating to obtain the best use of operating you...

Page 7 - Serial Decal Location:; The serial decal is located on the inside left arm of the loader; Serial Number; Buhler Manufacturing; Warranty Registration:; The

bühler Allied Front-End Loader Some components are identified as “right” and “left”. This is determined as seated in the tractor and facing forward, loader end. Serial Decal Location: The serial decal is located on the inside left arm of the loader joint plate. Please record the serial number in the...

Page 8 - SAFETY; Operate the loader while seated in the tractor seat only.

bühler Allied Front-End Loader SAFETY Read and understand all the safety messages listed in this manual. For your safety and the safety of others near the machine, learn how to control and operate the loader properly. It is your responsibility to inform subsequent operators and owners of these preca...

Page 9 - Important Precautions:; The alert symbol is used throughout this manual. It indicates; CAUTION; injury. It may also be used to alert against unsafe practices.

bühler Allied Front-End Loader Safety Decals: Safety Decal Location illustrates the approximate location and detail of safety decals. To install safety decals ensure the installation area is clean and dry.Decide on the exact position before you remove the backing paper. Remove thesmallest portion of...

Page 11 - FALLING HAZARD

bühler Allied Front-End Loader The following pictorials indicate important precautions to be used during the operation of the loader. - 9 - P4110 WARNING WARNING WARNING FALLING HAZARD To prevent serious injury or death: Do not lift, carry or allow anyone to ride on or work from any portion of loade...

Page 12 - PRE – OPERATION; Tractor Manual; Tractor Manual

bühler Allied Front-End Loader PRE – OPERATION WARNING The tractor must be equipped with an approved Roll over Protection Structure (ROPS) and safety belts to help prevent personal injuryor death caused by tractor roll over. CAUTION Maximum rated loader capacity may exceed tractor rating. Load restr...

Page 13 - OPERATION; The following section provides general

bühler Allied Front-End Loader OPERATION General Operating Notes: The following section provides general information that can be applied towards your specific application. Ensure thatyou’ve read and understood this manual and your Tractor Manual . Observe all safety precautions and follow local laws...

Page 15 - ackfilling or Scraping:; ling rod for a guide to

bühler Allied Front-End Loader Minimize turning angle and length of run Carry the load no between pile and trailer to increase loading efficiency. Also, place load evenly orcentered in the attachment. WARNING r to highe than necessary clear the terrain. Turn and brake slowly. Always be sure that loa...

Page 16 - position must be used to

bühler Allied Front-End Loader or back grading, either load the bucket and position must be used to – Frame: Standard and Heavy Duty A – Frames can be fitted with either Standard Duty uty frame is for handling Heavy Duty 60” 60” frame is for handling ty frame can also be Fposition the heel on the gr...

Page 17 - andling bales and pallets:

bühler Allied Front-End Loader andling bales and pallets: or safe handling of bales and pallets please follow procedures below: H F WARNING Do not operate A – Frame for bales without the stabilizers. With a single spear, enter one of the ends of ith the double or four spears enter the bale the bale ...

Page 18 - hly

bühler Allied Front-End Loader When loading bales onto a trailer, park trailer s you lift the bale using the regular loader, it in close proximity to minimize turning angle and length of travel to increase loadingefficiency. Ais recommended to feather the valve to allowbucket cylinders to extend to ...

Page 19 - Manure tine

bühler Allied Front-End Loader pictorial below for options listed) Grapple: The grapple is designed to safely prevent loads (bales, silage) from falling out of the bucket. (Refer to WARNING Trave at low speeds. Carry loads as low as possible. Avoid sharp turns and uneven terrain. l - 17 - P4110 Manu...

Page 20 - INSTALLING / REMOVING LOADER; Prior to initial mounting, cycle loader cylinders to; Verify front and side clearances during installation to

bühler Allied Front-End Loader INSTALLING / REMOVING LOADER Installing: CAUTION Prior to initial mounting, cycle loader cylinders to displace air. This ensures the loader will remain in the storage position and operate consistently. 1. Position the tractor centrally and parallel to the loader uprigh...

Page 21 - Shut tractor off and store parking stands within loader; A bucket or other suitable attachment must be attached

bühler Allied Front-End Loader 5. With the tractor in neutral, continue to retract the lift cylinders and extend the bucketcylinders to rotate the upright back against the lock pin stops. Shut the tractor off and set park brake. 6. Install both upright attachment pins and secure with hairpin clip. S...

Page 22 - Operate hydraulic

bühler Allied Front-End Loader 2. Lower attachment level to the ground while engaging float position. Ensure attachment rests firmly on ground with minimal downward pressure. If required extend bucketcylinders to rotate upright rearward. At this stage the pin should have no pressure. Set tractor par...

Page 23 - INSTALLING / REMOVING LOADER ATTACHMENTS

bühler Allied Front-End Loader INSTALLING / REMOVING LOADER ATTACHMENTS Installing: 1. Position tractor centrally within the bucket hooks. Dump Quick-tach slightly from vertical position. Slowly drive the tractor forward until the Quick-tach contacts the bucket. 2. Slowly raise the loader to engage ...

Page 24 - LUBRICATION; Ensure that grease fittings accept grease. Should any fitting

bühler Allied Front-End Loader - 22 - P4410 LUBRICATION Lubricate loader bushings and pivots every eight hours of average operation with high-grade grease. For grease fitting locations see illustration below. Select grease based on the expected outside temperature range. Lithium, Molybdenum and synt...

Page 25 - MAINTENANCE; Hydraulic Lift Lock Instructions Decal; Hydraulic Lift Lock:

bühler Allied Front-End Loader - 23 - P4410 MAINTENANCE General Inspection: CAUTION Lower attachment and loader to ground, place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing loader. WARNING Relieve hydraulic pres...

Page 27 - Escaping fluid under pressure can; Never operate the loader with frayed or damaged hoses

bühler Allied Front-End Loader - 25 - P4410 Hydraulics: WARNING Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Before repairing, adjusting, or disconnecting lines, be sure to relieve all pressure. Before applying pressure to the system...

Page 28 - Shut tractor down and relieve oil pressure in system by; Never use grease to lubricate valve components where

bühler Allied Front-End Loader - 26 - P4410 A yearly inspection of the valve is recommended. However the maintenance intervals on the valve depends on the surrounding environment or if valve spools become stiff. Where temperatures fluctuate from one extreme to another or exposed to high salt the int...

Page 30 - TSL GENERAL NOTE AND INSTRUCTIONS; true self leveling system; If the loader is raised with the; oil from the bucket piston side will be bypassed at; If the loader is lowered with the bucket; oil from the bucket shaft side will be bypassed at high

bühler Allied Front-End Loader - 28 - P4410 TSL GENERAL NOTE AND INSTRUCTIONS 1. The true self leveling system (TSL) utilizes mechanical linkages to maintain bucket level while raising and lowering. The pivot plate weldment, leveling tubes and linkages have been developed to ensure that the bucket r...

Page 31 - TROUBLE SHOOTING; Problem

bühler Allied Front-End Loader - 29 - P4410 TROUBLE SHOOTING Possible Cause Quick couplers leaking Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking. Control valve does not shift properly. Air in hydraulic system. Cylinder leaks internally. Faulty valve...

Page 32 - Trouble Shooting Continued; Possible Cause

bühler Allied Front-End Loader - 30 - P4410 Trouble Shooting Continued Problem Insufficient lift capacity. Slow leak down. Excessive wear on bottom of bucket and wear pads. Hydraulic cylinders inoperative. Pump operating continually on closed center tractor hydraulics system. Loader lift and bucket ...

Page 33 - PARTS APPENDIX; Description Page

bühler Allied Front-End Loader - 31 - P4110 2895 – 2895 S PARTS APPENDIX Description Page 2895-2895 S Main Frame Assembly ............................................................................... 32 Hydraulic Plumbing ...............................................................................

Page 34 - Main Frame Assembly

bühler Allied Front-End Loader - 32 - P4110 2895 – 2895 S Main Frame Assembly 28 32 31 33 19 16 25 26 35 27 34 14 29 30

Page 35 - Description

bühler Allied Front-End Loader - 33 - P4110 2895 – 2895 S Main Frame Assembly Item Part No. Description 2895 2895 S 1 24966 2895 Main Frame Weldment 1 - 1 24944 2895 S Main Frame Weldment - 1 2 25165 2895 Quick Attach Weldment 1 1 3 Ref. Lift Cylinder (see cylinder assembly) 2 2 4 Ref. Bucket Cylind...

Page 36 - Hydraulic Plumbing Assembly

bühler Allied Front-End Loader - 34 - P4110 2895 – 2895 S Hydraulic Plumbing Assembly

Page 42 - Possible Attachment Interference (S2895 and 2895 TSL)

bühler Allied Front-End Loader - 40 - P4110 Possible Attachment Interference (S2895 and 2895 TSL) Regular loader linkage setup allows for maximum rollback. TSL loader linkage setup provides reduced rollback. Large attachments (such as the C2000 Grapple) may contact the S2895 or 2895 TSL pivot plate....

Page 43 - Maximum pressure – 3000 psi

bühler Allied Front-End Loader - 41 - P4110 2895 Cylinder Assembly NOTES:1. Bucket cylinder shown 2. All cylinder seals are contained in corresponding seal kit. 3. Refer to page 44 for prevailing torque for locknuts. CAUTION Maximum pressure – 3000 psi Bucket Cylinders Lift Cylinders Regular & T...

Page 44 - Hydraulic Fitting Torques:

bühler Allied Front-End Loader - 42 - P4110 Hydraulic Fitting Torques: (ft-lbs) (NM) (ft-lbs) (NM) -04 7/16-20 14-16 20-22 10-11 13-15 -05 1/2-20 18-20 24-27 13-15 18-20 -06 9/16-18 24-26 33-35 17-19 23-26 -08 3/4-16 50-60 68-78 34-38 47-52 -10 7/8-14 72-80 98-110 50-56 69-76 -12 1-1/16-12 125-135 1...

Page 46 - a partnership”; CANADIAN WAREHOUSES

Buhler Manufacturing “ a partnership” Customer Support: 1-888-524-1003 1260 Clarence Ave. Box 7300 Winnipeg, MB. R3C 4E8 Ph.: (204) 661-8711 Fax: (204) 654-2503 www.buhler.com Printed in Canada Allied Division 1201 Regent Ave. W. Box 1003 Winnipeg, MB R2C 3B2 Ph.: (204) 661-8712 Fax: (204) 654-4331 ...