Brother WL-660 Series- Manuals

Page 2 - Action 2: Install the Toner Cartridge/Drum Unit; CAUTION; Install the drum unit into the printer.

2 English Action 2: Install the Toner Cartridge/Drum Unit 1 Unpack the drum unit and gently shake itfrom side to side five or six times. 2 Remove the protective parts, in order, asshown in the illustration. CAUTION Do not expose the drum unit to light forlonger than a few minutes, as this willdamage...

Page 3 - marks are

3 English 5 Unpack the toner cartridge and gently rockit from side to side well before installing.( ① ) Then, remove the protective parts. ( ② ) CAUTION DO NOT MOVE THE SHUTTER LEVERUNTIL THE CARTRIDGE ISINSTALLED. 6 Install the toner cartridge into the drumunit. Make sure that the ▲ marks are align...

Page 4 - Action 3: Load Paper into Your Printer; Open the multi-purpose sheet feeder cover.; NOTE; Move the paper guide to fit the paper width.

4 English Action 3: Load Paper into Your Printer 1 Install the paper support into the multi-purpose sheet feeder. ( ① ) Install the sheet feeder into the printer.( ② ) 2 Open the multi-purpose sheet feeder cover. 3 Load paper into the multi-purpose sheetfeeder. NOTE The feeder can hold up to 200 she...

Page 6 - Action 4: Connect Your Printer and Computer

6 English Action 4: Connect Your Printer and Computer You must connect the printer to your computer using an interface cable. A parallel cable isused for this connection. 1 Make sure that the power cord is unpluggedbefore connecting or disconnecting theinterface cable. Also, make sure that the compu...

Page 7 - Action 5: Plug in the Power Cord and Turn on Your Printer

7 English Action 5: Plug in the Power Cord and Turn on Your Printer 1 Plug the power cord into the AC poweroutlet. NOTE This printer has no power switch. Theprinter has a sleep mode that allows theprinter to automatically reduce powerconsumption when not in use. 2 Make sure that the READY lamp is ON...

Page 8 - Action 6: Set up the Printer Driver and Fonts for Windows 3.1

8 English Action 6: Set up the Printer Driver and Fonts for Windows 3.1 Check the following system requirements to run the Setup program and operate the printercorrectly: • IBM PC or compatible with 80486 SX or higher microprocessor • Parallel interface (or printer port) • 4 MB or more of memory • 1...

Page 9 - The Setup program makes the installed printer driver default.

9 English NOTE • The Setup program automatically updates Windows SYSTEM.INI file by addingDEVICE=bi-di.386 under the [386Enh] section. If any bi-directional parallelcommunications device driver has been previously installed, it will be deactivated by thisnew driver. If you want to use the previous d...

Page 10 - Action 7: Set Print Options of Your Printer; Open Control Panel in the Main group window.

10 English Action 7: Set Print Options of Your Printer Before you print documents, set the print options of your printer as follows: 1. Make sure that Windows is restarted immediately after running the Setup program. 2. Open Control Panel in the Main group window. 3. Open Printers in the Control Pan...

Page 11 - Action 8: Print Documents with Your Printer; Type and save a document to be printed.

11 English Action 8: Print Documents with Your Printer Now you can print documents from within your application software. Although print menusare somewhat different from application to application, you can print a document with thefollowing basic steps: 1. Start your application software. 2. Type an...

Page 12 - Shipment of the Printer; Remove the drum unit.

12 English Shipment of the Printer If for any reason you must ship your Printer, carefully package thePrinter to avoid any damage during transit. It is recommended that yousave and use the original packaging. The Printer should also beadequately insured with the carrier. Warning When shipping the Pr...