Brother S-7200C- Manuals

Page 3 - SAFETY INSTRUCTIONS; [1] Safety indications and their meanings; DANGER; Symbols

S-7200C i SAFETY INSTRUCTIONS [1] Safety indications and their meanings This instruction manual and the indications and symbols that are used on the machine itself are provided in order to ensure safe operation of this machine and to prevent accidents and injury to yourself or other people. The mean...

Page 4 - ii; Installation

S-7200C ii [2] Notes on safety DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the cover of the control box. Touching areas where high voltages are present can result in severe injury. CAUTION Environmental requir...

Page 5 - iii; CAUTION

S-7200C iii CAUTION Sewing This sewing machine should only be used by operators who have received the necessary training in safe use beforehand. The sewing machine should not be used for any applications other than sewing. Be sure to wear protective goggles when using the machine. If goggles are not...

Page 6 - iv

S-7200C iv [3] Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are difficult to read, please contact your nearest Brother dealer. 1 2 Touching areas where hi...

Page 7 - CONTENTS; CONVENIENT FUNCTION FOR

S-7200C CONTENTS 1. CONVENIENT FUNCTION FOR SMOOTH SEWING ............................... 1 2. NAMES OF MAJOR PARTS ................. 2 3. INSTALLATION .................................... 3 3-1. Table processing diagram ................................ 4 3-2. Installation..............................

Page 8 - CONVENIENT FUNCTION FOR SMOOTH SEWING

S-7200C 1. CONVENIENT FUNCTION FOR SMOOTH SEWING 1 1. CONVENIENT FUNCTION FOR SMOOTH SEWING Thread take-up amount can be adjusted Lower thread counter (When using the G50 operation panel) INSTRUCTION MANUAL CD 10-4. Adjusting the thread take-up amount INSTRUCTION MANUAL CD 5-7. Using the lower threa...

Page 9 - NAMES OF MAJOR PARTS; G10 operation panel (basic function LED)

S-7200C 2. NAMES OF MAJOR PARTS 2 2. NAMES OF MAJOR PARTS (1) Bobbin winder (2) Thread wiper (-4[][] specifications) (3) Lifting lever (4) Actuator switch (5) Presser foot (6) Knee lifter assembly (7) Power switch (8) Oil gauge window (-[]0[], []3[] specifications) (9) Reverse lever (10) Stitch leng...

Page 10 - About the machine set-up location

S-7200C 3. INSTALLATION 3 3. INSTALLATION CAUTION Machine installation should only be carried out by a qualified technician. Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done. The sewing machine weighs more than 45 kg. The installation should be ...

Page 12 - Knee lifter complying bar

S-7200C 3. INSTALLATION 5 3. Oil pan (1) Head cushions (left) [2 pcs] (2) Head cushions (right) [2 pcs] (3) Oil pan 4. Rubber cushions (1) Rubber cushions [2 pcs] (2) Nails [4 pcs] 5. Knee lifter complying bar (3) Knee lifter complying bar 6. Machine head (1) Hinges [2 pcs] (2) Machine head (3) Head...

Page 13 - Operation panel

S-7200C 3. INSTALLATION 6 7. Operation panel (1) Operation panel (2) Screws [2 pcs] (Use for tightening rear cover) 8. Sticker (Remove) (1) Sticker 9. Cotton stand (1) Cotton stand NOTE: Securely tighten the nut (4) so that the two rubber cushions (2) and the washer (3) are securely clamped and so t...

Page 14 - Knee lifter plate

S-7200C 3. INSTALLATION 7 10. Knee lifter plate (1) Knee lifter plate (2) Bolt * Loosen the bolt (3) and the bolt (4), and then adjust the position of the knee lifter plate (1) so that it is easy to use. <Knee lifter adjustment> 1. Turn the machine pulley so that the feed dog is below the top ...

Page 16 - Sewing machine cords

S-7200C 3. INSTALLATION 9 3-4. Connecting the cords DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the cover of the control box. Touching areas where high voltages are present can result in severe injury. CAUTION...

Page 17 - Binding the cords

S-7200C 3. INSTALLATION 10 (1) 6-pin head detector unit connector (2) 12-pin operation panel connector (3) 10-pin resolver connector (4) 14-pin machine connector (5) 4-pin motor connector 2. Binding the cords (1) Repeat cable tie NOTE: Bind the cords in such a way that the connector does not get pul...

Page 21 - Turning on the power

S-7200C 3. INSTALLATION 14 3-5. Test operation (Operating the treadle) CAUTION Do not touch any of the moving parts or press any objects against the machine while sewing, as this may result in personal injury or damage to the machine. 1. Turning on the power Press the ON power switch (1). The power ...

Page 23 - PREPARATION BEFORE SEWING

S-7200C 4. PREPARATION BEFORE SEWING 16 4. PREPARATION BEFORE SEWING 4-1. Installing the needle CAUTION Turn off the power switch before installing the needle. The machine may operate if the treadle is depressed by mistake, which could result in injury. 1. Turn the machine pulley to move the needle ...

Page 27 - USING THE G50 OPERATION PANEL

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 20 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 5-1. Names and functions • The operation panel keys cannot be operated while sewing is in progress. Select the keys and set the number of stitches before starting sewing. • In the case ...

Page 29 - -2. Sewing start and end backtack stitches

S-7200C 6. USING THE G50 OPERATION PANEL (ADVANCED OPERATIONS) 22 5-2. Sewing start and end backtack stitches 1 Setting start backtack stitches 2 Setting end backtack stitches 3 Start backtacking is carried out. After it has finished, normal sewing continues for as long as the treadle remains depres...

Page 32 - Contents of the Document CD; The following documents are contained in PDF format.; How to use the Document CD; Microsoft® Internet Explorer 6 Service Pack 1 or higher; Document CD

For cleaning, standard adjustments and more details, please refer to the instruction manual contained in the Document CD. Contents of the Document CD The following documents are contained in PDF format. ・ Basic Operation Manual ・ Instruction Manual ・ Parts Book How to use the Document CD Refer to “U...