Broilmaster BHA-1 - Manuals

Page 8 B101502-1-0311 BHa & BHaX a sseMBly Attention: If applicable, remove protective film from parts before installation. 1. Remove the surround from the shipping box and place the BHA surround into position in the constructed enclosure. See Figure 1. 2. Secure the BHA surround to the enclosur...

Page 10 B101502-1-0311 10. Install each of the four vent covers (BRB Vent Register Kit) into the Built-In Kit Enclosure using two #8 x 3/4” screws. See Figure 9. BHa & BHaX a sseMBly Figure 9 Figure 10 Alternate Match Lighting Instructions 1. Turn the burner control knobs clockwise to the OFF po...

Page 11 B101502-1-0311 BBA-1 T ANK C ADDY INSTALLATION INSTRUCTIONS T HE BBA T ANK C ADDY IS DESIGNED TO BE USED AS EITHER AN ENCLOSURE FOR A PORTABLE PROPANE TANK OR A GARBAGE RECEPTACLE . P LEASE REFER TO THE APPROPRIATE SECTIONS OF THIS MANUAL FOR PROPANE TANK REQUIREMENTS , CONNECTIONS , AND SAF...

Page 12 B101502-1-0311 BBa t anK c aDDy e XPlODeD v iew anD P arts l ist 1 2 3 VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE BEEN INCLUDED IN THIS BUILT-IN KIT BEFORE BEGINNING THIS INSTALLATION. CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES. WORK GL...

Page 13 B101502-1-0311 BBA T ANK C ADDY I NSTALLATION Recommended Tools: Phillips Screw Driver or an electric screw driver. Make sure BBA Tank Caddy opening dimensions match those in FIGURE 1. Place the BBA Frame Assembly in the Built-In Enclosure. Secure the BBA Frame to the Enclosure with eight (8...

Page 14 B101502-1-0311 Lower the BBA Door Assembly onto the two hinge pins inside the lower left and right sides of the BBA Frame. FIGURE 4 . ENCLOSURE REQUIREMENTS The enclosure design must be constructed to allow only storage of the LP cylinder in use thus preventing storage of a second cylinder. ...

Page 15 B101502-1-0311 T HE BSA S IDE B URNER S URROUND IS DESIGNED TO BE USED WITH THE DPASBC N ATURAL and P ROPANE G AS S IDE B URNER ONLY. D O NOT USE ANY OTHER SIDE BURNER WITH THE BSA S IDE B URNER S URROUND . BSA-1 SIDE BURNE r surrOunD Kit I NSTALLATION I NSTRUCTIONS nOtice: r eFer tO tHe B u...

Page 16 B101502-1-0311 Bsa s iDe B urner s urrOunD e XPlODeD v iew anD P arts l ist All repair part orders should be placed through your local Broilmaster ® dealer. To locate a dealer in your area, contact Broilmaster ® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and acc...

Page 17 B101502-1-0311 1 3 Bsa i nstallatiOn F IGURE 1 F IGURE 3 Make sure BSA Side Burner Surround opening dimensions match those in FIGURE 1. Place the BSA Liner into the Enclosure and check for proper hole alignment. Secure the BSA Liner to the Enclosure with four (4) 8 x 3/4” Hex Head screws. Yo...

Page 18 B101502-1-0311 T HE BDA S INGLE D OOR KIT IS DESIGNED TO BE USED IN AN ISLAND OR OTHER APPLICATION. BDa-1 sinGle/DOuBle DOOr Kit I NSTALLATION I NSTRUCTIONS nOtice: r eFer tO tHe B uilt -i n K it e nclOsure c OnstructiOn G uiDe FOr PrOPer DiMensiOns OF tHe OPeninG FOr tHe BDa-1 s inGle /D Ou...

Page 19 B101502-1-0311 BDa s inGle D OOr e XPlODeD v iew anD P arts l ist All repair part orders should be placed through your local Broilmaster ® dealer. To locate a dealer in your area, contact Broilmaster ® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and accurate serv...

Page 20 B101502-1-0311 2 1 3 BDa s inGle D OOr i nstallatiOn FIGURE 1 FIGURE 3 Make sure BDA Single Door opening dimensions match those in FIGURE 2. Place the Frame into the opening and check for proper hole alignment. Secure the Frame to the grill enclosure with eight (8) 8 x 3/4” Hex Head Screw sc...

Page 21 B101502-1-0311 BDA D OUBLE D OOR I NSTALLATION FIGURE 6 1 Remove doors from frames by depressing one of the spring loaded pins on each door and set them aside . Disassemble frame by removing the two screws and door pin from both door frames as shown in FIGURE 5. 27 ½” 19 13/16” Use the door ...

Page 22 B101502-1-0311 The BRB Vent Register Kit is designed to be used with any enclosure that has an LP tank. BRB-1 VENT REGISTER KIT I NSTALLATION I NSTRUCTIONS nOtice: r eFer tO tHe B uilt -i n K it e nclOsure c OnstructiOn G uiDe FOr PrOPer DiMensiOns OF tHe OPeninG FOr tHe BrB-1 v ent r eGiste...

Page 23 B101502-1-0311 BrB v ent r eGister c Over K it e XPlODeD v iew anD P arts l ist All repair part orders should be placed through your local Broilmaster ® dealer. To locate a dealer in your area, contact Broilmaster ® Customer Service at 800-851-3153 • www.broilmaster.com. To ensure prompt and...

Page 24 B101502-1-0311 LIMITED WARRANTY Manufactured in U.S.A. by Broilmaster, a Division of Empire Comfort Systems, Inc., P.O. Box 529, Belleville, Illinois 62222. WHAT IS COVERED AND FOR HOW LONG From the date these kits are purchased for use, Broilmaster will make available, at our factory, a fre...

Page 28 B101502-1-0311 T HE M OST D URABLE G RILL K NOWN T O M AN BROILMASTER ® A Division of Empire Comfort Systems, Inc. 918 Freeburg Ave. Belleville, Illinois 62220 Phone: 1-800-851-3153 FAX: 1-800-443-8648 VISIT OUR WEB SITE AT WWW.broilmaster.com