Briggs & Stratton LT-200 - Manuals

Page 2 - SAFETY RULES

LT-200 Series TP 300-4517-00-RG-N 3/2007 2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severepersonal injury or death to you, yourself or bystanders, or damage to property or equipment. This mowing deck is capable ofamput...

Page 4 - Uncrating; IMPORTANT NOTE; Charge Battery; WARNING; Install Battery

LT-200 Series TP 300-4517-00-RG-N 3/2007 4 Uncrating Using a reciprocating utility saw or equivalent, cut crateaway from bottom skid. Remove crate. Remove shrink-wrap plastic. 2. Cut banding from front and rear tractor axles. Cut banding from mower rollers. Remove mower frombottom skid. 3. Hold brak...

Page 6 - Functional Tests; Mower Blade Stopping Check; Operational SAFETY Checks

LT-200 Series TP 300-4517-00-RG-N 3/2007 6 Figure 4. Seat SwitchA. Seat SwitchB. Wiring Harness PerformSafety Checks Functional Tests 1. Check the tractor for loose bolts, screws, nuts, etc. 2. Start the engine and check all controls for proper operation: ground speed control pedals, clutch/brakeped...

Page 7 - Torque Mower Blades; Size

LT-200 Series 3/2007 7 TP 300-4517-00-RG-N Figure 5. Blade TorqueA. 4x4 Wood BlockB. Spline or Hex WasherC. Spring WasherD. Blade Bolt Torque Mower Blades 1. Secure the hex washer (B, Figure 5), spring washer (C) and capscew (D). Use a wooden block (A) toprevent blade rotation while tightening the b...

Page 8 - Lubrication

LT-200 Series TP 300-4517-00-RG-N 3/2007 8 Lubrication Lubricate the unit at the locations shown in Figures 7-10as well as the lubrication points listed. Generally, allmoving metal parts should be oiled where contact ismade with other parts. Keep oil and grease off belts andpulleys. Wipe surfaces cl...

Page 9 - Hourmeter

LT-200 Series 3/2007 9 TP 300-4517-00-RG-N Figure 8. Mower Lubrication Points Figure 10. Arbor Lubrication Point Figure 9. Mower Lubrication Points Hourmeter HOURMETER MODELS The hour meter measures the number of hours the keyhas been in the RUN position. This hourmeter can notbe reset and does not ...

Page 10 - CAUTION

LT-200 Series TP 300-4517-00-RG-N 3/2007 10 Mower Deck Removal &Installation Removing the Mower Deck 1. Park tractor on a hard, level surface such as a concrete floor. Turn off PTO switch and engine,remove the key and apply parking brake. 2. Place wood blocks under the mower deck. Place the atta...

Page 11 - Leveling The Mower

LT-200 Series 3/2007 11 TP 300-4517-00-RG-N Leveling The Mower If the cut is uneven, the mower may need leveling.Unequal or improper tire pressure may also cause anuneven cut. Make sure tire pressure is correct asspecified in Checking Tire Pressure. SIDE-TO-SIDE LEVELING 1. With the mower installed,...

Page 12 - Gauge Wheels; Seat Adjustment; Seat Slide Adjustment

LT-200 Series TP 300-4517-00-RG-N 3/2007 12 Gauge Wheels The mower gauge wheels can be placed in severalpositions depending on the height of cut. When usinghigher cutting heights, set the wheels in the lowerposition. When using lower cutting heights, set thewheels in the upper position. To adjust: 1...

Page 14 - Mower Belt Replacement

LT-200 Series TP 300-4517-00-RG-N 3/2007 14 Mower Belt Replacement Note: It is not necessary to remove the mower to install anew belt. However, for easier access mower can beremoved. See Mower Removal in the Operation section. 1. Park the tractor on a smooth, level surface such as a concrete floor. ...