Briggs & Stratton 5900703 - Manuals

Briggs & Stratton 5900703 – Manual in PDF format online.

Manuals:

Manual

Manual Briggs & Stratton 5900703

Summary

Page 2 - THIS PAGE INTENTIONALLY BLANK

THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)

Page 3 - Table of Contents

1 Cover and Bag Installation Install Cover Assembly ....................................7 Install Collector Bags .......................................7 Tube Installation Lower Tube Installation ....................................8 Connecting Upper and Middle Tube ................8 Collector Insta...

Page 4 - SAFETY DECALS; GENERAL WARNINGS; Attachment Decal; WARNING

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of controlof unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. Thetriangle in text signifies important cautions or warnings which must be followed. 2 Safet...

Page 5 - After Operation; CAUTION; Storing the Grass Catcher; General

CAUTION Before you begin operating the unit be certainyou have read all of the safety and operationalinformation of this instruction sheet, as well asthe Operator’s Manual for the tractor and anyother attachments. Never operate on slopes greater than 17.6% (10°). After Operation Remove any debris fr...

Page 6 - Tube Component Assembly

4 BAFFLE INSTALLATION 1. Determine which baffle to use (See Chart). 2. Lift side discharge chute (H, Figure 1). 3. Insert baffle (F) through discharge opening and posi- tion baffle into place. 4. Tighten carriage bolts (A) and locknut(s) (E) on baffle (F). 5. Tighten carriage bolt (B) and locknut(s)...

Page 7 - Component Installation

5 Component Installation Figure 3. Lower Chute to Boot InstallationA. Latch PinB. Carriage Bolt, 1/4-20 x 5/8C. Locknut, 1/4-20D. Lower ChuteE. Locknut, Center Lock, 5/16-18F. Rubber StrapG. Locknuts, Whiz Lock, 5/16-18H. Rod, Boot MountI. Capscrew, Hex Head, 5/16-18 x 1-1/4 J. Capscrew, Hex Head, T...

Page 8 - Bag and Cover Support Installation

6 Bag and Cover Support Installation INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 5) to upright support (A) using the capscrews (C) and thelocknuts (D). A B Figure 5. Install Bag and Cover SupportA. Upright Support B. Bag and Cover SupportC. Capscrews, 3/8-16 x 1D. L...

Page 9 - Cover and Bag Installation

Cover and Bag Installation 7 Figure 6. Install Cover AssemblyA. Bag Support BracketB. Cover AssemblyC. Cover Hinge PinsD. Hair PinsE. Hinge Pivots INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 6) to bag support bracket (A) using hinge pivots (E). Secure coverusing cover hinge pins (C) a...

Page 10 - Tube Installation

Tube Installation 8 LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 8). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole closest to knob in strap completely over locknut (E). CONNECTING UPPER AND MIDDLE TUBE 1. Slide the upp...

Page 11 - Collector Installation and Removal

9 A. Hitch Support Assembly J. DeflectorB. Cover K. Nut & Capscrew C. Pins L. Mounting Plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge I. Strap, Boot R. Ridge Cutout E Q B COLLECTOR INSTALLATION Note: S...

Page 12 - Carrier Installation

10 Carrier Installation Figure 12. Front Weight Carrier InstallationA. Holes D. Rod B. Capscrews, E. Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknuts, 1/2-13 FRONT WEIGHT CARRIER INSTALLATION 1. Install carrier (F, Fgure 12) as shown securing with capscrews (B), and locknuts (C). 2. Secur...

Page 13 - Hitch Plate and Back Plate Installation

11 Hitch Plate and Back Plate Installation FLAT STYLE BUMBER 1. Remove and discard hardware holding heat shield (B, Figure 13) to upper and lower bumper (E). 2. Open existing holes (F) in heat shield (B) and upper & lower bumper (E) to 17/32”. 3. Install hitch plate (A) to upper and lower bumper...

Page 14 - Grass Catcher Removal an d Attachment

12 Grass Catcher Removal an d Attachment REMOVING THE GRASS CATCHER 1. Remove the hair pin clips (B, Figure 16) and hinge pins (D) and remove the cover (A). A B C D Figure 16. Remove the CoverA. Cover C. Hinge B. Hair Pin Clip E. Hinge Pin 2. Remove the bags (A, Figure 17) by tilting them off their ...

Page 15 - Grass Catcher Removal and Attachment

13 Grass Catcher Removal and Attachment ATTACHING THE GRASS CATCHER 1. Set the back plate and support (A, Figure 19) onto the pins of the hitch plate (C). Secure with rod (D)and hair pin (B). 2. Hook the bags on the back plate (Figure 7). 3. Install the catcher cover (A, Figure 7) and secure with th...