BMW M3 CONVERTIBLE 2004- Manuals

6 Notes Maintenance and repair Advanced technology, e.g. the use of modern materials and high- performance electronics, requires spe-cially adapted maintenance and repair methods. Therefore, only have corre-sponding work on your BMW carried out by a BMW center or a workshop that works according to B...

7 Notes Service and warranty This manual is supplemented by a Ser-vice and Warranty Information Booklet for US models or a Warranty and Ser-vice Guide Booklet for Canadian mod-els. We recommend that you read this pub-lication thoroughly. Your BMW is covered by the following warranties: > New Vehi...

Contents Notes About this Owner's Manual 4 Additional sources of information 4 Symbols used 4 Your individual vehicle 5 Status at time of printing 5 For your own safety 5 Symbol on vehicle parts 6 Service and warranty 7 Reporting safety defects 7 Overview Cockpit 14 Instrument cluster 16 Indicator a...

Contents 9 Driving: Ignition lock 65 Starting the engine and driving off 66 Switching off the engine 68 Parking brake 68 Manual transmission 69 Sequential M gearbox with Drivelogic* 70 Turn signal indicator/Headlamp flasher 75 Washer/wiper system/Rain sensor* 76 Cruise control 77 Everything under co...

Contents Owner service procedures Replacement procedures: Onboard tool kit 136 Windshield wiper blades 136 Lamps and bulbs 137 Repairing a flat tire 140 Battery 144 Fuses 145 Giving and receiving assistance: Receiving assistance 146 Jump-starting 147 Towing the vehicle 148 Technical data Engine data...

14 Cockpit Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

16 Instrument cluster Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

18 Indicator and warning lamps Technology that monitors itself Indicator and warning lamps that are identified by ● are tested for proper functioning whenever the ignition key is turned. They each light up once for dif-ferent periods of time. If a fault should occur in one of these systems, the corr...

19 Red and yellow: continue driving cautiously The brake warning lamp comes on together with the yellow indi-cator lamps for ABS ● and DSC:The entire ABS, CBC and DSC control system has failed. Con-tinue to drive; drive cautiously and defensively and avoid full brake applications. Please have the sy...

20 button or in response to a system mal-function. In the event of a malfunction, have the system checked by your near-est BMW center.For additional information: refer to page 86 Dynamic Brake Control (DBC) ● Malfunction in DBC system. Conventional braking efficiency is available and unrestricted.Ha...

21 Blue: for your information High beamsComes on when the high beams are on or the headlamp flasher is actuated.For additional information: refer to pages 75 , 92 Indicator and warning lamps Overview Controls Maintenance Repairs Data Index Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

22 Buttons in steering wheel These buttons let you operate the fol-lowing functions quickly and without being distracted from traffic conditions: > Selected radio functions > The cruise control > Selected telephone functions. * The controls are active only when the corresponding systems and...

23 Hazard warning triangle* The hazard warning triangle is stored ready to use in the luggage compart-ment lid inside the toolbox for the onboard tool kit. To open the container, loosen the wing nut. Always observe all legal regula-tions requiring a warning triangle to be carried in the vehicle. <...

24 Refueling Fuel filler door Always switch off the engine before refueling, as it is not possi- ble to add fuel with the engine running, and attempts may also trigger the SERVICE ENGINE SOON lamp. < Press on the rear edge of the fuel filler door to open and close it. If an electrical malfunction...

25 Close the gas cap carefully after refueling until a click is heard. While closing, be sure not to squeeze the strap which is fastened to the cap. A loose or missing cap will activate the CHECK GAS CAP * lamp. < Fuel tank capacity > Approx. 16.6 gal./63 liters, of which > approx. 2.1 gal....

26 Check the tire pressures on a reg-ular basis – at least twice a month – and before every extended journey. If this is not done, incorrect tire pressures can cause driving instability and tire damage, ultimately resulting in acci-dents. < Comply with tire approval specifications The inflation p...

30 Opening and closing Keys The key set 1 Master keys with remote control unit – these keys determine the functions of the Key Memory. Refer to page 64 . You can mark the individual keys for subsequent identification by apply-ing the colored decals that you received when accepting delivery of your v...

31 Opening and closing – via the remote control The concept The remote control also provides two additional functions beyond the central locking feature: > Switch on the interior lamps, refer to page 32 . With this function you can also search for your vehicle – when parked in an underground gara...

33 Opening and closing – via the door lock Turning the key in the door lock once unlocks the driver's door, the fuel filler door and the glove compartment. Turning the key a second time unlocks the passenger's door and the luggage compartment lid. You can have a signal set to con-firm that the vehic...

34 Opening and closing – from the inside You can use this button to control the central locking system whenever the doors are closed. The doors and lug-gage compartment lid are unlocked or locked only. The anti-theft system is not activated. If only the driver's door was unlocked from the outside an...

35 Luggage compartment lid The lock Only the master keys fit in the lock for the luggage compartment lid, refer to page 30 . To secure separately Lock the glove compartment using the master key. The luggage compartment lid is locked and disconnected from the central lock-ing system. This feature can...

37 Luggage compartment To fold up and secure the floor panel 1. Pull up at the handle and fold the panel up 2. Press the button to release the hanger from the handle 3. Hook the handle into the rubber seal of the drip rail. Carefully replace the hanger in its holder when lowering the floor panel bac...

38 When opening the convertible top, refer to page 39 , make sure that the convertible top compartment panel is folded down in the luggage compart-ment; otherwise you may damage something. < Electric power windows To open and close windows When leaving the vehicle, always remove the ignition key ...

39 Operating all windows at once With the ignition key in position 1 or higher > Press the switch until you feel resis-tance: all of the windows will con-tinue to lower as long as you con-tinue to press the switch > Press the switch briefly past the pres-sure point: all windows will move autom...

41 2. Ensure that the convertible top com- partment panel in the luggage com-partment is folded down, see page 37 ; otherwise, it will not be possible to open the convertible top 3. Make sure that the luggage compart- ment lid is closed 4. Press and hold the corresponding button for convertible top ...

44 Position for cleaning To be able to access the convertible top compartment, lean the rear frame of the convertible top against the cover of the convertible top compartment. First, use the button for activating the convertible top to unlock the locks of the convertible top compart-ment. Refer to p...

45 3. Hold the wind deflector so that the smaller half points toward the front and guide the mounting pin for the side piece into the proper opening 4. Pull back on the mounting pin for the other side piece by using a slide, so that the mounting pin can be guided into the opening provided 5. Unlock ...

46 To adjust Safe seating position For driving that is relaxed and less likely to cause fatigue, you should select a sitting position that reflects your per-sonal requirements. In combination with the safety belts and airbags, the correct seating position also plays an important role in enhancing oc...

47 Seats When adjusting your seat, always observe the following precautions Never try to adjust your seat while operating the vehicle. The seat could respond with an unexpected movement, and the ensuing loss of vehicle control could lead to an acci-dent. Never ride with the backrest reclined to an e...

48 Adjusting the lumbar support* You can adjust the backrest's contour for additional support in the curvature of your spine's lumbar region. The upper hips and spinal column receive supplementary support to help you maintain a relaxed, upright position. > Increase/decrease curvature: press front...

49 Rear head restraints The rear head restraints may only be lowered if there are no passen- gers in the rear seats. If you do so, you are in violation of the law. Raise the rear head restraints before taking on any passengers in the back. < To completely lower the rear head restraints: 1. Press ...

50 The seat can be locked into posi-tion when it is tilted forward. This is particularly convenient when entering the vehicle on an incline, for example. Press against the backrest until you hear it snap into place. Lever 1 does not have to be released to fold the seat back. < Lock both backrests...

51 Seat and mirror memory You can store and recall three different driver's seat and outside mirror posi-tions. Memory will not retain the adjust-ment made to the lumbar sup- port. < To store 1. Ignition key in position 1 or 22. Adjust your seat and outside mirrors to the desired position 3. Pres...

53 Steering wheel To adjust Never attempt to adjust the steer-ing wheel while driving the vehicle – it could respond with unexpected movement, posing a potential accident hazard. < 1. Push the locking lever downward2. Adjust steering column reach and height for your selected seating posi-tion 3. ...

55 Passenger safety systems Airbags 1 Front airbags on the driver and pas- senger sides 2 Side airbags on the driver and pas- senger sides – front and rear * Protective effect The front airbags protect the driver and passenger in the event of a head-on collision where the protection provided by the ...

57 This is the right way a larger child should sit wearing the seat belt when rear side airbags are provided. Indicator lamp The indicator lamp indicates the operational status of the airbag system when the ignition key is in position 1 or higher. System operational: > The indicator lamp comes on...

58 Transporting children safely Leave the rear safety belts in the holders if they are not needed to avoid unwanted movement from the safety belts at high speeds. < Commercially available child seats complying with the legal standard are designed to be secured with a seat belt or with the seat be...

62 Rollover protection system In the event of an accident or some other critical driving situation – extreme tilting in the longitudinal or transverse axis, loss of contact with the ground – the rollover protection system will be automatically activated. The protective bars located in the rear head ...

64 Vehicle Memory, Key Memory How the system functions You have probably frequently wished that you could configure individual functions of your vehicles to reflect your own personal requirements. In engi-neering your vehicle, BMW has pro-vided for a number of options for per-sonal adjustment that c...

65 Driving Ignition lock Ignition key positions 0 Steering locked 1 Steering unlocked 2 Ignition on 3 Start engine Steering locked The key can only be inserted and removed in this position. After removing the key, turn the steer-ing wheel slightly to the left or right until you hear the lock engage....

66 Starting the engine and driving off Do not allow the engine to warm up by leaving it running while the vehicle remains stationary. Instead, drive off immediately at a moderate engine speed. < Do not allow the engine to run in enclosed spaces. Otherwise, breathing the exhaust fumes can lead to ...

68 Switching off the engine You should never remove the igni-tion key when the vehicle is in motion, as the steering lock could engage.When you leave the vehicle, always remove the ignition key and engage the steering lock. < Always engage the parking brake when parking on downhill roads. Engagin...

69 If exceptional circumstances make it necessary to engage the parking brake while the vehicle is in motion, do not pull it with excessive pressure. Keep your thumb pressed against the release button while care-fully pulling the lever up.Excessive pressure can lead to over-braking and loss of tract...

70 Sequential M gearbox with Drivelogic* The concept The sequential M gearbox with Drivelogic is an automated manual gearbox with which clutching and shift-ing is assumed by an electro-hydraulic system. The SMG Drivelogic is operated via two shift paddles on the steering wheel and the selector lever...

71 Display in instrument cluster The selector lever position, currently engaged gear and selected driving pro-gram are displayed in the instrument cluster. 1 Engaged gear 2 Selected driving program, corre- sponds to the number of illuminated fields, refer to page 73 3 Tapping the selector lever to t...

73 Drivelogic Drivelogic makes various driving pro-grams available to you. Press the Drivelogic repeatedly until the desired driving program is shown in the SMG display of the instrument cluster, refer to page 71 . In the automated mode you can select from five driving programs ranging from convenie...

74 Indicator lamp The gearbox indicator lamp in the instrument cluster goes out after the engine is started. > If it does not go out, or if it lights up during driving, a malfunction has occurred. The available functions may be limited under certain circum-stances.Drive carefully and with the Dyn...

75 Turn signal indicator/Headlamp flasher 1 High beams – blue indicator lamp 2 Headlamp flasher – blue indicator lamp 3 Turn signal indicator – green indicator lamps accompanied by a periodic clicking sound from the relay To signal briefly Press the lever up to but not beyond the detent. It then ret...

77 0 Wipers retracted 1 Clean windshield and headlamps Clean windshield and headlamps* Do not use the washers if there is any danger that the fluid will freeze on the windshield, as your vision could be obscured. Always use a wind-shield washer antifreeze in cold weather. Refer to page 126 . Do not ...

79 Everything under control Odometer 1 Odometer 2 Trip odometer Odometer You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the left button in the instrument cluster. Trip odometer To reset the trip odometer to zero, press the left button with the...

80 Fuel gauge Once the indicator lamp stays on con-tinuously, there are still approx. 2 gallons/8 liters of fuel in the fuel tank. Fuel tank capacity approx. 16.6 gal./ 63 liters. If the tilt of the vehicle varies – when you are driving in mountainous areas, for example – the needle may fluctuate sl...

81 Service interval display Remaining distance to next service The displays shown in the illustration appear for a few seconds when the ignition key is in position 1 or higher or after the engine is started. The next service due appears with the message OIL SERVICE or INSPECTION, together with the d...

82 Clock If you wish to have a permanent time display, you can make this adjustment in the car radio display, refer to the Owner's Manual for Radio. You can set the time of day, and the display for the car radio, as follows. Setting Before the clock can be set, the time must be showing in the instru...

83 Computer Mode selection With the ignition key in position 1 and higher, you can use the button in the turn signal lever to retrieve information from the computer for display in the instrument cluster. Each time you press the button briefly in the direction of the steering column, a new function i...

84 Average fuel consumption If you continue to press and hold the button on the turn signal lever, the aver-age fuel consumption being displayed is recalculated from that point. If you wish, you can have the aver-age fuel consumption displayed in a different unit of measure. < Range The computer ...

86 Dynamic Stability Control DSC The concept DSC maintains vehicle stability, even in critical driving situations. The system optimizes vehicle stability during acceleration and when starting from a full stop, as well as optimizing traction. In addition, it recognizes unstable vehicle conditions, su...

87 To deactivate the system Press the button; the indicator lamp comes on and stays on. The vehicle does not execute the stabil-ity-enhancement and traction-control functions when DSC is deactivated. We recommend that you deactivate the system for increased traction: > When rocking the vehicle or...

89 To activate/deactivate the system The system is automatically activated in ignition key position 2 and conse-quently is on whenever the vehicle is operated. To deactivate the system: tap the but-ton; the indicator lamp will light up yel-low. To activate the system: tap the button again; the indic...

91 Lamps Parking lamps/Low beams Parking lamps The front, rear and side vehicle lighting is switched on. You can use this to signal the position of the vehicle when it is parked. For light-ing on one side for parking as an addi-tional feature, refer to page 92 . Low beams When you switch the ignitio...

92 Instrument lighting Turn the rotary dial to control the light-ing when the parking or low beam lamps are on. High beams/Standing lamps 1 High beams – blue indicator lamp 2 Headlamp flasher – blue indicator lamp 3 Standing lamps Standing lamps, left or right As an additional feature, you can illum...

93 Fog lamps Front fog lamps The green indicator lamp in the instrument cluster lights up to indicate that the front fog lamps are on. If the automatic headlamp control is on, the low beams will come on automatically whenever you activate the front fog lamps. < Interior lamps The interior lamps o...

96 Controlling the climate for pleasant driving Automatic climate control Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

101 Interior conveniences Glove compartment To open Pull the handle. The glove compartment will light up. To close Fold up cover. To prevent injury in the event of an accident, close the glove com- partment immediately after use. < To lock Lock with one of the master keys. A master key can also b...

102 Beverage holders, coin box A coin box and two beverage holders are provided in the center console. Storage package* The following are available for your convenience: > Two flip-out power sockets on the rear center console > An eyeglasses storage compart-ment * , not shown, in the center co...

104 Loading and transporting Ski bag* The ski bag allows the safe and clean transport of up to 3 pairs of standard skis or up to two snowboards. The length of the ski bag and the addi-tional space provided in the luggage compartment make it possible to carry skis up to 6 ft 10 in / 2.10 m long. Beca...

105 5. Secure the cover panel with the magnetic retainer on the rear wall and pull out the ski bag. Securing cargo Secure skis and any other objects stored in the bag by tightening the retaining strap at the buckle. < Please be sure that the skis are clean before loading them into the bag. Be car...

106 Cargo loading Avoid overloading the vehicle so that the permitted load on the tires is not exceeded. Overloading can lead to overheating and internal tire damage. This can result in a sudden loss of tire inflation pressure. < Determining the maximum load 1. Locate the following statement on y...

107 Stowing cargo > Load heavy cargo as far forward as possible – directly behind the lug-gage compartment partition – and as low as possible > Cover sharp edges and corners. You can enlarge the luggage com-partment when the convertible top is closed, refer to page 37 . To do this you have to ...

108 Always position and secure the load correctly. If you do not, it can endanger the passengers during brak-ing or evasive maneuvers.Do not exceed the approved gross vehicle weight or the approved axle loads, refer to page 156 , otherwise the vehicle's operating safety is no longer assured and the ...

112 Special operating instructions Break-in procedures To ensure that your vehicle continues to provide maximum economy throughout an extended service life, we request that you devote careful attention to the following instructions. Because of its engineering design, the BMW M3 Convertible is an esp...

113 Clutch The clutch will also begin to function optimally after about 300 miles/500 km. Drive cautiously during this break-in period and do not press the clutch or shift at high engine speeds. General driving notes Brakes: do not drive with your foot resting on the brake pedal. Even light but cons...

114 Antilock Brake System (ABS) The concept ABS keeps the wheels from locking during braking, thereby enhancing active driving safety. Braking with ABS If you are in a situation that requires full braking, you will exploit the full benefits of ABS system if you apply maximum pedal pressure – panic s...

118 Wheels and tires Tire inflation pressure Information for your safety The factory-approved tires are matched to your vehicle and have been selected to provide optimum safety and driving comfort when used properly. It is not merely the tire's service life, but also driving comfort and – above all ...

119 Do not drive on a deflated – flat – tire. A flat tire greatly impairs steering and braking response, and can lead to complete loss of control over the vehicle.Avoid overloading the vehicle so that the permitted load on the tires is not exceeded. Overloading can lead to overheating and internal t...

120 Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive tem-perature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard ...

121 Wheel and tire combinations The right choice BMW recommends using only wheels and tires that have been approved by BMW for your particular vehicle model, as otherwise body con-tact and serious accidents can result despite the use of the same nominal size, e.g. due to manufacturing toler-ances. I...

122 Winter tires Choosing the right tire BMW recommends the use of winter tires for operation under winter road conditions. While all-season tires – with M+S designation – provide better winter traction than the corresponding sum-mer tires, they generally do not achieve the performance of winter tir...

123 In the engine compartment Hood To release Pull the lever located under the left-hand side of the instrument panel. Do not attempt to service your vehicle if you do not have the required technical background. Failure to work in an informed, professional manner when servicing components and materi...

124 Engine compartment essentials Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

126 Washer fluids Headlamp* and windshield washer system Capacity approx. 5.6 US quarts/5.3 liters. Fill with water and, if required, with a washer antifreeze additive according to manufacturer's recommendations. We recommend that you mix the washer fluid before adding it to the reservoir. < Anti...

127 Adding engine oil Only add engine oil when the oil level has dropped to just above the lower mark on the dipstick. Do not fill beyond the upper mark on the dipstick. Excess oil will damage the engine. Before checking the engine oil level after topping up, restart the engine and allow it to run t...

128 However, if the vehicle is exposed to temperatures below –4 7 /–20 6 for extended periods, please have your BMW center recommend a suitable oil. Coolant Do not add coolant to the cooling system when the engine is hot. If you attempt to do so, escaping coolant can cause burns.Antifreeze and anti-...

129 3. If necessary, add coolant. If the cool- ant is low, slowly add coolant until the correct level is reached — do not overfill. Brake fluid Indicator lamp The brake warning lamp comes on when the parking brake is not engaged: brake fluid level too low, refer to page 18 . Brake warning lamp for C...

130 Maintenance The BMW Maintenance System The BMW Maintenance System has been designed as a reliable means of providing maximum driving and operat-ing safety – and as cost-effectively for you as possible. Please keep in mind that regular maintenance is not only necessary for the safety of your vehi...

131 Care You can find everything you need to know on this topic by consulting the separate Caring for your vehicle bro-chure. The BMW Maintenance System Overview Controls Maintenance Repairs Data Index Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

132 Laws and regulations California Proposition 65 warning California laws require us to state the following warning: Engine exhaust and a wide variety of automobile components and parts, including components found in the interior furnishings in a vehicle, con-tain or emit chemicals known to the Sta...

133 If the indicator blinks or flashes, this indicates a high level of engine misfire. Reduce speed and contact your near-est BMW center immediately. Severe engine misfiring for even a short period of time can seriously damage emission-control system components, especially the catalytic converter. S...

136 Replacement procedures Onboard tool kit The onboard tool kit is located in the luggage compartment lid. To open, loosen the wing nut. For stor-age place of towing eyelet, refer to page 148 . Windshield wiper blades 1. Switch off the engine2. Fold the wiper arm completely out from the windshield ...

137 Lamps and bulbs The lamps and bulbs make essential contributions to the safety of your vehi-cle. Therefore, proceed carefully when handling bulbs. BMW recommends that you have such work performed by your BMW center if you are not familiar with the procedures. Do not touch the glass portion of a ...

139 Rear lamps 1 Turn signal indicator 2 Backup lamp 21 watt bulb 3 Tail lamp/brake lamp All bulbs in the fender are designed using LED technology. Please contact a BMW center in case of a malfunction. < Bulbs in the luggage compartment lid1. Using a screwdriver, loosen the clip 2. Fold the trim ...

140 Center high-mount brake lamp LED strip in luggage compartment lid. Please contact a BMW center in case of a malfunction. License plate lamps 5 watt bulb 1. Place a screwdriver in the slot and press toward the left to release the lens 2. Replace the bulb. Repairing a flat tire Precautions in case...

141 Using the M Mobility system To repair a flat tire using the M Mobility system, proceed as follows: > Preparing the M Mobility system for use, refer to the next column > Components of the M Mobility sys-tem, refer to page 142 > Filling with sealant, refer to page 142 > Distributing se...

142 Components of the M Mobility system 1 On/Off switch 2 Connection hose with manometer for connecting the compressor with the sealant container or to connect the compressor to the wheel 3 Manometer for indicating the tire pressure 4 Connector hose from the sealant container to the wheel 5 Sticker ...

143 4. Make sure that the screw on the rear of the pressure gauge 3 is tightened down. Turn on the M Mobility sys-tem, position I, refer to illustration, and allow minutes to elapse, to let the sealant flow in. It does not matter afterward, what the tire's inflation pressure is 5. Turn the system of...

144 Even if the tire fails to hold the pressure, you should still carry out Step 3 before proceeding to drive the vehicle again, refer to Distributing the sealant for more information. Then repeat Steps 1 through 3.The use of the M Mobility system may be ineffective if the damaged area in the tire i...

145 Fuses You will find the fuses and information on their respective allocation in the glove compartment behind a panel with two snap clips. Do not attempt to repair a blown fuse or replace it with a fuse having a different color or amperage rating. To do this could cause a fire in the vehicle resu...

146 Giving and receiving assistance Receiving assistance The BMW Group's Mobile Service offers you 24-hour assistance in the event of a breakdown, even on week-ends and holidays. The telephone numbers of the Mobile Service control center in your country are listed in the BMW Dealer Directory. If you...

148 2. Start the engine of the other vehicle as usual. If the first start attempt is not suc-cessful, wait a few minutes before another attempt in order to allow the discharged battery to recharge 3. Allow the engines to run for several minutes 4. Disconnect the jumper cables in reverse sequence. Ha...

154 Engine data DisplacementNumber of cylinders cu in/cm 3 198.1/3,2466 Max. power outputat engine speed hprpm 3337,900 Maximum torqueat engine speed lb ft/Nmrpm 262/3554,900 Compression ratio ε 11.5 StrokeBore in/mmin/mm 3.58/913.43/87 Fuel mixture preparation Digital electronic engine-management s...

155 Dimensions Overview Controls Maintenance Repairs Data Index Online Edition for Part-No. 01 41 0 157 596 - © 09/03 BMW AG

156 Weights Curb weight lbs/kg 3,782/1,715 Approved gross vehicle weight lbs/kg 4,608/2,090 Approved front axle load lbs/kg 2,183/990 Approved rear axle load lbs/kg 2,513/1,140 Permissible roof load for the hardtop lbs/kg 165/75 Luggage compartment capacitywith the convertible top compartment raised...

157 Capacities Notes Fuel tankReserve gal./litersgal./liters approx. 16.6/63approx. 2.1/8 Fuel specification, refer to page 25 Windshield washer system/Headlamp cleaning system quarts/liters approx. 5.6/5.3 Specifications, refer to page 126 Engine with oil filter change quarts/liters approx. 5.8/5.5...

Everything from A to Z A ABS Antilock Brake System 114 indicator lamp 19 Accessories, refer to For your own safety 5 Accident, refer to Emer- gency call 146 Activated-charcoal filter 100 Adding brake fluid 129 Adding liquid sealant Mobility system 142 Additional sources of infor- mation 4 Air condit...

Refueling To ensure that you always have conve-nient access to all essential information when you stop for fuel, we recommend that you take the time to fill out the adjoining chart by entering the data that apply to your vehicle. Consult the index for individual specifications. Fuel Please enter you...