BMW M3 CONVERTIBLE 2003- Manuals

6 Notes dust shields, telephones – including operation of any portable cellular phone from within the vehicle without using an externally mounted antenna – or trans-ceiver equipment, such as CB, walkie-talkie, ham radio or similar, may cause extensive damage to the vehicle, com-promise its safety, i...

Contents Notes About this Owner's Manual 4 Symbols used 4 Your individual vehicle 4 Status at time of printing 5 For your own safety 5 Symbol on vehicle parts 6 Service and warranty 6 Reporting safety defects 6 Overview Cockpit 14 Instrument cluster 16 Indicator and warning lamps 18 Steering wheel w...

Contents 9 Passenger safety systems: Airbags 57 Transporting children safely 59 Rollover protection system 63 Vehicle Memory, Key Memory 65 Driving: Ignition lock 66 Starting engine and driving off 67 Switching off the engine 69 Parking brake 69 Manual transmission 70 Sequential M gearbox SMG II* 71...

Contents Owner service procedures Replacement procedures: Onboard tool kit 134 Windshield wiper blades 134 Lamps and bulbs 135 Repairing a flat tire 139 Battery 143 Fuses 144 Giving and receiving assistance: Jump-starting 145 Towing the vehicle 146 Technical data Engine data 150 Dimensions 151 Weigh...

14 Cockpit handbook.book Page 14 Tuesday, July 30, 2002 9:28 AM Online Edition for Part-No. 01 41 0 156 854 - © 09/02 BMW AG

16 Instrument cluster handbook.book Page 16 Tuesday, July 30, 2002 9:28 AM Online Edition for Part-No. 01 41 0 156 854 - © 09/02 BMW AG

18 Indicator and warning lamps Technology that monitors itself Indicator and warning lamps that are identified by ● are tested for proper functioning whenever the ignition key is turned. They each light up once for dif-ferent periods of time. If a fault should occur in one of these systems, the corr...

19 Red and yellow: continue driving cautiously The red brake warning lamp lights up together with the yel-low indicator lamps for ABS ● and DSC:The entire ABS, CBC and DSC control system has failed. Con-tinue to drive; drive cautiously and defensively and avoid full brake applications. Please have t...

20 button or in response to a system mal-function. In the event of a malfunction, have the system checked by your near-est BMW center.For additional information: refer to page 87 Dynamic Brake Control (DBC) ● Malfunction in DBC system. Conventional braking efficiency is available and unrestricted.Ha...

21 Blue: for your information High beamsComes on when the high beams are on or the headlamp flasher is actuated.For additional information: refer to pages 76 , 93 Indicator and warning lamps Overview Controls Maintenance Repairs Data Index handbook.book Page 21 Tuesday, July 30, 2002 9:28 AM Online ...

22 Steering wheel with multifunction buttons These buttons let you operate the fol-lowing functions quickly and without being distracted from traffic conditions: > Selected radio functions > The cruise control > Several telephone * functions. The controls are active only when the correspond...

23 Hazard warning triangle* The hazard warning triangle is stored ready to use in the luggage compart-ment lid inside the toolbox for the onboard tool kit. To open the container, loosen the wing nut. Always observe all legal regula-tions requiring a warning triangle to be carried in the vehicle. <...

24 Refueling Fuel filler door Always switch off the engine before refueling, as it is not possi- ble to add fuel with the engine running, and attempts may also trigger the SERVICE ENGINE SOON lamp. < Press on the rear edge of the fuel filler door to open and close it. If an electrical malfunction...

25 Close the fuel filler cap carefully after refueling until a click is heard. While closing, be sure not to squeeze the strap which is fastened to the cap. A loose or missing cap will activate the CHECK FILLER CAP lamp. < Fuel tank capacity > Approx. 16.6 gal./63 liters, of which > approx....

26 Check the tire pressures on a reg-ular basis – at least twice a month – and before every extended journey. Incorrect tire pressure can otherwise lead to driving instability, tire damage and accidents. < Comply with tire approval specifications The inflation pressures in the table apply to BMW-...

30 Opening and closing Keys The key set 1 Master keys with remote control unit – determine the functions of the Key Memory, refer to page 65 . You can mark the individual keys for subsequent identification by apply-ing the colored decals that you received when accepting delivery of your vehicle Ther...

31 Opening and closing – via the remote control The concept The remote control gives you an excep-tionally convenient method for unlock-ing and locking your vehicle. Further-more, it provides two additional functions: > Switch on the interior lamps, refer to page 32 . With this function you can a...

32 To lock and secure Press button. To switch on the interior lamps After locking the vehicle, press button again. To deactivate the tilt alarm* and interior motion sensors* Press button a second time immedi-ately after locking. For additional information: page 39 . To open the luggage compartment P...

33 Opening and closing – via the door lock Turning the key in the door lock once unlocks the driver's door, the fuel filler door and the glove compartment. Turning the key a second time unlocks the passenger's door and the luggage compartment lid. You can have a signal set to con-firm that the vehic...

34 Opening and closing – from the inside With this button you operate the central locking system whenever the doors are closed. The doors and luggage com-partment lid are unlocked or locked only. The anti-theft alarm system is not activated. If only the driver's door was unlocked from the outside an...

35 Luggage compartment lid The lock Only the master keys fit in the lock for the luggage compartment lid, refer to page 30 . To secure separately Lock the glove compartment using the master key. The luggage compartment lid is locked and disconnected from the central lock-ing system. If you surrender...

37 Luggage compartment To fold up and secure the floor panel 1. Pull up at the handle and fold the panel up 2. Press the button – see arrow – to release the hanger from the handle 3. Hook the handle into the rubber seal of the drip rail – see arrow. Carefully replace the hanger in its holder when lo...

40 Electric power windows To open and close windows When leaving the vehicle, always remove the ignition key from the lock and remember to close the doors to prevent children from operating the power windows and injuring them-selves, etc. < With the ignition key in position 1 or higher > Press...

41 After the ignition has been switched off After the ignition has been switched off: You can still use the electric power win-dows for up to 15 minutes, as long as no one opens any of the doors. Convertible top The completely automatically operated convertible top combines assured pro-tection again...

42 Driving with the opening or clos-ing operation not completely ended can lead to damage and/or inju-ries.Traffic laws applicable in your area take precedence when you operate the con-vertible top, otherwise you may be breaking the law.Do not lay objects on the convertible top, since they would fal...

45 4. Lift out the cover panel that is in the center of the front convertible top frame 5. Put the Allen wrench 2 – refer to page 44 – into the hex slot – see arrow 6. Pull down on the front convertible top frame as far as possible. Close the convertible top further by turning the wrench in a clockw...

46 Wind deflector* With the convertible top open, the wind deflector keeps air movement in the passenger compartment to a minimum, thus providing you with a pleasant drive, even at higher speeds. The wind deflector comes in a protective sleeve, and because of its slim dimensions, can be easily store...

47 7. Close the convertible top compart- ment lid via the convertible top con-trol button. The wind deflector is now attached so that it is theft-proof. Operate the convertible top com-partment lid from above only in order to avoid any pinching.With the wind deflector in place: never push the front ...

48 To adjust Safe seating position For relaxed and fatigue-free driving you should select a sitting position that reflects your personal requirements. In combination with the safety belts and airbags, the correct seating position plays an important role in enhancing occupant safety in the event of a...

49 Seats When adjusting your seat, always observe the following precautions Never try to adjust your seat while operating the vehicle. The seat could respond with an unexpected movement, and the ensuing loss of vehicle control could lead to an acci-dent. Never ride with the backrest reclined to an e...

50 Adjusting the lumbar support* You can adjust the backrest's contour for additional support in the curvature of your spine's lumbar region. The upper hips and spinal column receive supplementary support to help you maintain a relaxed, upright position. > Press the front/rear of switch: increase...

51 Rear head restraints The rear head restraints may only be lowered if there are no passen- gers in the rear seats. If you do so, you are in violation of the law. Raise the rear head restraints before taking on any passengers in the back. < To completely lower the rear head restraints: 1. Press ...

52 Press against the backrest until you hear it snap into place. Lever 1 does not have to be released to fold the seat back. < Lock both backrests while driving, otherwise there is a danger of an unexpected movement causing an accident. < The indicator lamp in the instrument cluster flashes, w...

53 Seat and mirror memory You can store and recall three different driver's seat and outside mirror posi-tions. The setting for the lumbar support is not stored in memory. < To store 1. Ignition key in position 1 or 22. Adjust your seat and outside mirrors to the desired position 3. Press the MEM...

55 Steering wheel To adjust Never attempt to adjust the steer-ing wheel while driving the vehicle – it could respond with unexpected movement, posing a potential accident hazard. < 1. Push the locking lever downward2. Adjusting steering column reach and rake for your selected seating posi-tion 3....

57 Passenger safety systems Airbags 1 Front airbags on the driver and pas- senger sides 2 Side airbags on the driver and pas- senger sides – front and rear * Protective effect The front airbags protect the driver and passenger in the event of a head-on collision where the protection provided by the ...

58 erly positioned at all times and not place their heads on or near the side airbag. Therefore, we recommend that the rear seat side airbags, if provided, be deactivated if you plan to transport children in the rear seat.The rear seat side airbags may already have been deactivated, either at the ti...

60 Depending on the location selected for seating in the rear passenger area, attach the tether strap to the corre-sponding anchorage point to secure the child-restraint system, as shown in the illustration. 1. Open the convertible top compart- ment lid, refer to page 41 2. Lift the headrest and pas...

63 Rollover protection system In the event of an accident or some other critical driving situation – extreme tilting in the longitudinal or transverse axis, loss of contact with the ground – the rollover protection system will be automatically activated. The protective bars located in the rear head ...

65 Vehicle Memory, Key Memory How the system functions You have probably frequently wished that you could configure individual functions of your vehicles to reflect your own personal requirements. In engi-neering your vehicle, BMW has pro-vided for a number of options for per-sonal adjustment that c...

66 Driving Ignition lock Ignition key positions 0 Steering locked 1 Steering unlocked 2 Ignition switched on 3 Starting engine Steering locked The key can be inserted or removed in this position only. After removing the key, turn the steer-ing wheel slightly to the left or right until the lock engag...

67 Starting engine and driving off Do not allow the engine to warm up by leaving it running while the vehicle remains stationary. Instead, drive off immediately at a moderate engine speed. < Do not allow the engine to run in enclosed spaces. Otherwise, breathing the exhaust fumes can lead to unco...

69 Switching off the engine You should never remove the igni-tion key when the vehicle is in motion, as the steering lock could engage.When you leave the vehicle, always remove the ignition key and engage the steering lock. < Always engage the parking brake when parking on downhill roads. Engagin...

70 If exceptional circumstances make it necessary to engage the parking brake while the vehicle is in motion, do not pull it with excessive pressure. Keep your thumb pressed against the release button while care-fully pulling the lever up.Excessive pressure can lead to over-braking and loss of tract...

71 Sequential M gearbox SMG II* The concept The sequential M gearbox SMG II is an automated manual gearbox with which clutching and shifting is assumed by an electro-hydraulic system. The SMG II is operated via two shift paddles on the steering wheel and the selector lever in the center console. It ...

72 Display in instrument cluster The selector lever position, currently engaged gear and selected driving pro-gram are displayed in the instrument cluster. 1 Engaged gear 2 Selected driving program, corre- sponds to the number of illuminated fields, refer to page 74 3 Tapping the selector lever to t...

73 Shifting gears with shift paddles on steering wheel: > To upshift, briefly pull the right pad-dle + > To downshift, briefly pull the left pad-dle –. Shift paddles with various widths matched to the shape of your hand are available from your BMW cen-ter. < Shifting gears with selector lev...

74 Drivelogic Drivelogic makes various driving pro-grams available to you. Press the Drivelogic repeatedly until the desired driving program is shown in the SMG display of the instrument cluster, refer to page 72 . In the automated mode you can select from five driving programs ranging from convenie...

75 Indicator lamp The transmission indicator lamp in the instrument cluster goes out after the engine is started. > If it does not go out, or if it lights up during driving, a fault has occurred. The available functions may be lim-ited under certain circumstances.Drive carefully and with the Dyna...

76 Turn signal indicator/Headlamp flasher 1 High beams – blue indicator lamp 2 Headlamp flasher – blue indicator lamp 3 Turn signal indicator – green indicator accompanied by periodic clicking sound from the relay To signal briefly Press the lever up to but not beyond the resistance point. It then r...

78 0 Wipers retracted 1 Clean windshield and headlamps Clean windshield and headlamps* Do not use the washers if there is any danger that the fluid will freeze on the windshield, as your vision could be obscured. Always use a wind-shield washer antifreeze in cold weather. Refer to page 124 . Do not ...

79 Cruise control is also deactivated when the ignition key is in position 0. The speed stored in memory is deleted. To store and maintain speed or to accelerate Press button "+" briefly: The system stores and maintains the current vehicle speed. Every time you tap the button, the speed incr...

80 Everything under control Odometer 1 Odometer 2 Trip odometer Odometer You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the left button, see arrow, in the instrument cluster. Trip odometer To reset the trip odometer to zero, press the left but...

81 Fuel gauge Once the indicator lamp stays on con-tinuously, there are still approx. 2 gallons/8 liters of fuel in the fuel tank. Fuel tank capacity approx. 16.6 gal./ 63 liters. If the tilt of the vehicle varies – when you are driving in mountainous areas, for example – the needle may fluctuate sl...

82 Service interval display Remaining distance to next service The displays shown in the illustration appear for a few seconds when the ignition key is in position 1 or higher or after the engine is started. The next service due appears with the message OIL SERVICE or INSPECTION, together with the d...

83 Clock If you wish to have a permanent time display, you can make this adjustment in the car radio * display, refer to the Owner's Manual for Radio. You can set the time of day, and the display for the car radio, as follows. To adjust When the ignition key is in position 1 or higher, the time of d...

84 Computer Mode selection With the ignition key in position 1 and higher, you can use the button in the turn signal lever to retrieve information from the computer for display in the instrument cluster. Each time you press the button briefly in the direction of the steering column, a new function i...

85 Average fuel consumption If you continue to press and hold the button on the turn signal lever, the aver-age fuel consumption being displayed is recalculated from that point. If you wish, you can have the aver-age fuel consumption displayed in a different unit of measure. < Range The computer ...

88 To reactivate the system Press the button again; the indicator lamp goes out. Dynamic Brake Control (DBC) DBC is an integral component of the DSC system. If you apply the brakes rapidly, this sys-tem automatically generates maximum braking force boost and thus helps to achieve the shortest possib...

89 Initializing the system Initializing is necessary to familiarize the system with the correct inflation pres-sures. Repeat this process after any changes in tire inflation pressure, tire rotation or replacement. 1. Check the tire inflation pressures in all the tires, comparing them with the inflat...

90 Flat tire The red warning lamp in the instrument cluster lights up to warn of pressure loss and tire failure. In addition, an acoustic signal is sounded. To come to an immediate stop, reduce speed, while avoiding any sudden, jerky braking or steering maneuvers. Fix the flat tire using the M Mobil...

91 M Engine dynamics control The system – Sport mode – will cause the engine to respond more spontane-ously to any motion of the accelerator pedal. Activating/deactivating Sport mode Activating: with the ignition key in posi-tion 2, press the SPORT button. The indicator lamp will come on. Each time ...

92 Lamps Parking lamps/Low beams Parking lamps The front, rear and side vehicle lighting is switched on. You can use this to signal the position of the vehicle when it is parked. For light-ing on one side for parking as an addi-tional feature, refer to page 93 . Low beams When you switch the ignitio...

93 Instrument lighting Turn the rotary dial to control the light-ing when the parking or low beam lamps are on. High beams/Standing lamps 1 High beams – blue indicator lamp 2 Headlamp flasher – blue indicator lamp 3 Standing lamps Standing lamps, left or right As an additional feature, you can illum...

94 Fog lamps Front fog lamps The green indicator lamp in the instrument cluster lights up to indicate that the front fog lamps are on. If the automatic headlamp control is on, the low beams will come on automatically whenever you activate the front fog lamps. < Interior lamps The interior lamps o...

95 Rear reading lamps With the hardtop reading lamps are also located in the rear, refer to page 113 . Switch on and off with the button adja-cent to each lamp. In order to prevent battery dis-charge, all of the lamps in the vehicle are automatically switched off approx. 15 minutes after you turn th...

96 Controlling the climate for pleasant driving Automatic climate control handbook.book Page 96 Tuesday, July 30, 2002 9:28 AM Online Edition for Part-No. 01 41 0 156 854 - © 09/02 BMW AG

101 Interior conveniences Glove compartment To open Pull the handle. The glove compartment will light up. To close Fold up cover. To prevent injury in the event of an accident, close the glove com- partment immediately after use. < To lock Lock with one of the master keys. A master key can also b...

102 Beverage holder, coin box A coin box and two beverage holders are provided in the center console. Cellular phone* Hands-free system In vehicles equipped with telephone preparation * or with the communica- tions package * , the cover for the hands-free microphone is located above the interior rea...

104 Loading and transporting Ski bag* The ski bag allows the safe and clean transport of up to 3 pairs of standard skis or up to two snowboards. The length of the ski bag and the addi-tional space provided in the luggage compartment make it possible to carry skis up to 6 ft 10 in / 2.10 m long. Beca...

105 5. Secure the cover panel with the magnetic retainer on the rear wall and pull out the ski bag. Securing cargo Secure skis and any other objects stored in the bag by tightening the retaining strap at the buckle. < Please be sure that the skis are clean before loading them into the bag. Be car...

106 Cargo loading Always position and secure the load correctly. If you do not, it can endanger the passengers during brak-ing or evasive maneuvers.Do not exceed the approved gross weight or the approved maximum axle loads, refer to page 152 . Otherwise the vehicle's operating safety is no longer as...

107 Securing the cargo in the luggage compartment > For small, light items, use the rubber-lined non-skid side of the floor mat or secure with a luggage compartment net * or elastic straps, refer to page 37 > For large, heavy pieces, see your BMW center for load-securing devices * . Lashing fi...

110 Special operating instructions Break-in procedures To ensure that your vehicle provides maximum economy throughout a long service life, we request that you observe the following suggestions. Because of its engineering design, the BMW M3 convertible is an especially high-quality vehicle. It is in...

111 Driving notes Brakes: do not rest your foot on the brake pedal while driving. Even light but consistent pedal pres-sure can lead to high temperatures, brake wear and possibly even brake failure.Hydroplaning: when driving on wet or slushy roads, reduce road speed. If you do not, a wedge of water ...

112 Brake system Brake fluid level Low brake fluid level in the reservoir combined with longer than usual pedal travel may indicate a defect in one of the brake system's hydraulic circuits. Proceed to the nearest BMW cen-ter. Higher brake application pres- sure may be necessary when stopping, and th...

113 Hardtop* It is not necessary to remove the fabric top even in the winter, when the hard-top is generally in constant use. But you can also remove it at any time with no problem. Before the fabric top is stored in the convertible top compartment, it must be absolutely dry in order to avoid water ...

115 Wheels and tires Tire inflation pressure Information for your safety The factory-approved tires are matched to your vehicle and have been selected to provide optimum safety and driving comfort when used properly. It is not merely the tire's service life, but also driving comfort and – above all ...

116 ceed carefully to the nearest BMW cen-ter or professional tire center, or have the vehicle towed in to have it, its wheels or its tires inspected.Tire damage, up to and including blow-outs, can endanger the lives of both the vehicle occupants and other road users < Tire replacement DOT qualit...

117 Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separate...

118 Wheel and tire combinations The right choice BMW recommends using only wheels and tires that have been approved by BMW for use on your par-ticular model. Although other wheels and tires may theoretically have the same dimensions, variations in factors such as manufacturing tolerances can result ...

119 Do not exceed specified maximum speeds Never exceed the maximum speed for which the winter tires are rated.Unprofessional attempts by laymen to service tires can lead to damage and accidents.Have this work performed by skilled professionals only. Your BMW center will be glad to assist you with b...

120 In the engine compartment Hood To release Pull the lever located under the left-hand side of the instrument panel. Do not attempt to service your vehicle if you do not have the required technical background. Failure to work in an informed, professional manner when servicing components and materi...

122 Engine compartment essentials handbook.book Page 122 Tuesday, July 30, 2002 9:28 AM Online Edition for Part-No. 01 41 0 156 854 - © 09/02 BMW AG

124 Washer fluids Headlamp* and windshield washer system Capacity approx. 5.6 US quarts/5.3 liters. Fill with water and – if required – with a washer antifreeze additive according to manufacturer's recommendations. We recommend that you mix the washer fluid before adding it to the reservoir. < An...

125 Adding engine oil While you should wait until the level has dropped to just above the lower mark before adding oil, you should never allow the oil level to fall below this mark. Do not fill beyond the upper mark on the dipstick. Excess oil will damage the engine. Before checking the engine oil l...

126 However, if the vehicle is exposed to temperatures below –4 7 /–20 6 for extended periods, please have your BMW center recommend a suitable oil. Coolant Do not add coolant to the cooling system when the engine is hot. If you attempt to do so, escaping coolant can cause burns.Antifreeze and anti-...

127 3. If necessary, add coolant. If the cool- ant is low, slowly add coolant until the correct level is reached — do not overfill. Comply with the applicable envi-ronmental laws regulating the dis- posal of antifreeze agents with corro-sion inhibitor. < Brake fluid Indicator lamp The brake warni...

128 Maintenance The BMW Maintenance System The BMW Maintenance System has been designed as a reliable means of providing maximum driving and operat-ing safety – and as cost-effectively for you as possible. Please keep in mind that regular maintenance is not only necessary for the safety of your vehi...

129 Care You can find everything you need to know on this topic by consulting the separate Caring for your vehicle bro-chure. The BMW Maintenance System Overview Controls Maintenance Repairs Data Index handbook.book Page 129 Tuesday, July 30, 2002 9:28 AM Online Edition for Part-No. 01 41 0 156 854 ...

130 Laws and regulations California Proposition 65 warning California laws require us to state the following warning: Engine exhaust, some of its con-stituents, and certain vehicle com- ponents contain or emit chemicals known to the State of California to cause cancer and birth defects and reproduct...

131 If the indicator blinks or flashes, this indicates a high level of engine misfire. Reduce speed and contact your near-est BMW center immediately. Severe engine misfiring for even a short period of time can seriously damage emission-control system components, especially the catalytic converter. S...

134 Replacement procedures Onboard tool kit The onboard tool kit is located in the luggage compartment lid. To open, loosen the wing nut. For stor-age place of towing eyelet, refer to page 146 . Windshield wiper blades 1. Switch off the engine2. Fold the wiper arm completely out from the windshield ...

135 Lamps and bulbs The lamps and bulbs make essential contributions to the safety of your vehi-cle. Therefore, comply fully with the fol-lowing instructions during bulb replace-ment. If you are not familiar with any of the procedures, consult your BMW center. Do not touch the glass portion of a new...

137 Tail lamps 1 Turn signal indicator 2 Backup lamp 3 Tail lamp 4 Tail lamp/brake lamp Tail lamp 4: 21/4 watt bulb Remaining bulbs: 21 watt The illustration shows the right-hand luggage compartment opening. Bulbs in the fender: All of the bulbs are integrated in a cen-tral bulb holder. 1. Release t...

138 Bulbs in the luggage compartment lid1. Using a screwdriver, loosen the clip 2. Fold the trim panel down – see arrow 1. Disengage the bulb holder – see arrow 2 – and remove it 3. Applying light pressure, turn the bulb to the left. Remove and exchange the bulb 4. Press the bulb holder into positio...

139 License plate lamps 5 watt bulb 1. Place a screwdriver in the slot and press toward the left – see arrow – to release the lens 2. Replace the bulb. Repairing a flat tire Precautions in case of a flat tire:Stop the vehicle as far as possible from passing traffic; switch on the haz-ard warning fla...

141 Filling with sealant 1. Take off the round cover and take out hose 4. Unscrew the valve dust cap from the defective wheel and screw the hose to the valve. Keep the dust cap in a safe place 2. Flip open the cover and pull out the enclosed protective gloves. Take out hose 2 with the manometer and ...

142 Do not exceed a maximum speed of 40 mph / 60 km/h. If possible, keep the vehicle speed above 10 mph / 20 km/h.Stop in a suitable spot. < Inflating tire to correct pressure 1. Take out the hose with the pressure gauge and screw it onto the valve.Take the plug out and plug it into the cigarette...

143 You will find corresponding instructions for using the M Mobility system on the device.Replace the defective tire as soon as possible and have the new wheel bal-anced. Reinitialize the Flat Tire Monitor, and refer to page 89 for further informa- tion. Have the M Mobility system refilled. Contact...

144 Fuses You will find the fuses and information on their respective allocation in the glove compartment behind a panel with two snap clips. Do not attempt to repair a blown fuse or replace it with a fuse having a different color or amperage rating. To do this could cause a fire in the vehicle resu...

146 Towing the vehicle Towing eyelet The towing eyelet, which can be unscrewed, is in the luggage compart-ment under the floor mat and must remain in the vehicle. This eyelet is designed for installation in the tow sockets located at the front and rear of the vehicle. It is intended for towing on pa...

147 Use only a nylon towing strap to tow the vehicle, since the inherent resil-ience of this material helps protect both vehicles from sudden jerking move-ments. The towed vehicle should always be the lighter of the two vehicles. If this is not the case, it will not be pos-sible to control vehicle h...

150 Engine data DisplacementNumber of cylinders cu in/cm 3 198.1/3,2466 Max. power outputat engine speed hp/kWrpm 333/2487,900 Maximum torqueat engine speed lb ft/Nmrpm 262/3554,900 Compression ratio ε 11.5 StrokeBore in/mmin/mm 3.58/913.43/87 Fuel-injection system Digital electronic engine-manageme...

151 Dimensions Overview Controls Maintenance Repairs Data Index handbook.book Page 151 Tuesday, July 30, 2002 9:28 AM Online Edition for Part-No. 01 41 0 156 854 - © 09/02 BMW AG

152 Weights Curb weight lbs/kg 3,782/1,715 Approved gross vehicle weight lbs/kg 4,630/2,100 Approved front axle load lbs/kg 2,183/990 Approved rear axle load lbs/kg 2,579/1,170 Permissible roof load for the hardtop lbs/kg 165/75 Luggage compartment capacitywith the convertible top compartment raised...

153 Capacities Notes Fuel tankReserve gal./litersgal./liters approx. 16.6/63approx. 2.1/8 Fuel specification: page 25 Windshield washer system/Headlamp cleaning system quarts/liters approx. 5.6/5.3 For details: page 124 Cooling system including heater circuit quarts/liters approx. 9.8/9.3 For detail...

Everything from A to Z A ABS Antilock Brake System indicator lamp 19 Accessories 5 Activated-charcoal filter 100 Adding brake fluid 122 , 127 Air conditioning 98 Air distribution, automatic 98 Air distribution, individual 98 Air nozzles 96 Air outlets 96 Air pressure 115 checking 25 Air supply 98 Ai...

Refueling To ensure that you always have conve-nient access to all essential information when you stop for fuel, we recommend that you take the time to fill out the adjoining chart by entering the data that apply to your vehicle. Consult the index for individual specifications. Fuel Please enter you...