Blanco CG905WXFFC - Manuals

Page 2 - DESCRIPTION OF THE HOT PLATES

2 NATURAL PROPANE 1 Wok burner 14.5 MJ 11.4 MJ 2 Rapid gas burner 12.0 MJ 10.4 MJ 3 Semi rapid gas burner (front and rear) 7.1 MJ 6.2 MJ 4 Auxiliary gas burner 4.1 MJ 3.5 MJ 5 Cast iron pan support 1F 6 Cast iron pan support 2F (right) 7 Cast iron pan support 2F (left) 8 Burner n° 1 control knob 9 B...

Page 3 - USE

3 1) BURNERS A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below: - Manual ignition Push and turn the knob corresponding to t...

Page 5 - CLEANING

5 CLEANING IMPORTANT: Always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 2) HOT PLATE Periodically wash the hot plate, the enamelled steel pan support, the enamelled burner caps “C” and the burner heads “T” (see fig. 6) with lukewarm soapy ...

Page 6 - ) INSTALLING THE HOT PLATE; INSTALLATION

6 TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL This appliance shall be installed only by authorised persons and in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, AS 5601/AG 601 - Gas Installati...

Page 7 - ) FIXING THE COOKTOP

7 4) FIXING THE COOKTOP The hot plate has a special seal which prevents liquid from infiltrating into the cabinet. Strictly comply with the following instructions in order to correctly apply this seal: - detach the seals from their backing, checking that the transparent protection still adheres to t...

Page 9 - ) ELECTRICAL CONNECTION

9 INSTALLATION 6) ELECTRICAL CONNECTION The appliance is supplied with a 1800 mm long flexible supply lead. The point of attachment for this lead is located at the rear and on the underside of the appliance 380 mm from the right hand side. The voltage and power consumption are detailed on the unders...

Page 10 - ADJUSTMENTS

10 Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. a) Data Label The Data Label is located on the underside of the ho...

Page 11 - CONVERSIONS

11 8) PROPANE GAS TO NATURAL GAS CONVERSION PROCEDURE Appliance models: Gas stainless steel hotplate models: CG905WXC 5 Burners CG905WXFFC 5 Burners 1. Remove each burner cap and burner skirt. 2. Remove the Propane Gas main injector with a 7 m m / V F t u b e s pa n n e r a n d r e p l a c e w i t h...

Page 12 - ) NATURAL GAS TO PROPANE GAS

12 CONVERSIONS 9) NATURAL GAS TO PROPANE GAS CONVERSION PROCEDURE Appliance models: Gas stainless steel hotplate models: CG905WXC 5 Burners CG905WXFFC 5 Burners 1. Remove each burner cap and burner skirt. 2. Remove the Natural Gas main injector with a 7 m m / V F t u b e s pa n n e r a n d r e p l a...

Page 13 - BURNER ARRANGEMENT ON THE HOT PLATE; TABLE

13 CONVERSIONS BURNER ARRANGEMENT ON THE HOT PLATE TABLE FIG. 15 BURNERS GAS NORMAL PRESSURE (kPa) INJECTOR DIAMETER (1/100 mm) N O M I N A L HEAT INPUT (MJ/h) MAX. BY PASS N° DESCRIPTION 1/100 mm 1 ULTRA RAPID PROPANE NATURAL 2.75 1.00 94 176 14.5 11.4 85 1/2 2 RAPID PROPANE NATURAL 2.75 1.00 91 15...

Page 14 - SERVICING; 0) COMPONENTS REPLACEMENT

14 SERVICING WARNING: S e r v i c i n g s h o u l d b e c a r r i e d o u t o n l y b y authorised personnel. 10) COMPONENTS REPLACEMENT NOTE: B E F O R E A N Y M A I N T E N A N C E R E Q U I R I N G R E P L A C E M E N T O F A C O M P O N E N T I S U N D E RTA K E N E N S U R E T H AT T H E ELECTR...

Page 15 - CABLE TYPES AND SECTIONS

15 SERVICING TYPE OF TYPE OF SINGLE - PHASE HOT PLATE CABLE POWER SUPPLY CABLE TYPES AND SECTIONS ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig. 22) and comply with the recommendations given in paragraph 6. FIG. 2...

Page 16 - TECHNICAL ASSISTANCE AND SPARE PARTS

16 TECHNICAL ASSISTANCE AND SPARE PARTS MEA Contact Information. NEW SOUTH WALES Head Office, Sales & Marketing Office 104 Vanessa Street Kingsgrove NSW 2208 Telephone: 02 9503 2888 Facsimile: 02 9503 2810 NSW Showroom* 40 Ebley Street Bondi Junction NSW 2022 Telephone: 02 9386 1190 Facsimile: 0...

Page 17 - WARRANTY SECTION

17 WARRANTY SECTION 1.Subject to the “Statement of Standard Warranty Conditions” this product is covered by the following Warranty. TWO (2) YEARS WARRANTY from date of purchase, covering all parts and labour. 2. The appliance is warranted under normal single family domestic installation and use, as ...