Black & Decker BC40EB - Manuals

Page 2 - READ ALL INSTRUCTIONS; Minimum Gage for Cord Sets

1 GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES READ ALL INSTRUCTIONS READ ALL INSTRUCTIONS WARNING: Read all instructions before operating product. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.• AVOID DANGEROUS ENVIRONMENTS: ...

Page 3 - SAFETY GUIDELINES / DEFINITIONS; RISK OF UNSAFE OPERATION.; IMPORTANT SAFETY INSTRUCTIONS; WARNING: RISK OF EXPLOSIVE GASES

2 SAFETY GUIDELINES / DEFINITIONS DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially h...

Page 5 - INTRODUCTION; Thank you for selecting the

4 Follow these steps when the battery is installed in a vehicle. A spark near the battery may cause an explosion. CAUTION: TO REDUCE RISK OF A SPARK NEAR THE BATTERY: 1. Position AC and DC cords away from hood, door, or moving engine parts.2. Stay clear of fan blades, belts, pulleys, and other parts...

Page 6 - Stage Three —; Top-Off Charge voltage is; FEATURES; Controls and Indicators; Charge Curve

5 to allow for the maximum proper internal chemical energy transfer. At the end of Stage 2, the charger willautomatically move into Stage 3 charge mode. Stage Three — Top-Off Charge voltage is automatically maintained and reduced to apredetermined level while current is adjustedfor a safe, effective...

Page 7 - OPERATING INSTRUCTIONS; AC POWER INDICATOR; FAULT CODES

6 4/10/20/40A AMP (Charge Rate Selector) (Step 2) allows the user to select the charge rate based on battery size. This selection and the actual battery charge rate are monitored by the microprocessor. The chargerwill stop charging if the rate is too fast or too slow for the battery size or conditio...

Page 8 - The default selection is “GEL” type battery.; Automatic Float Charging; returns to “FUL” when completed.; Equalizing

7 Charge Rate Selection After charger clamps are correctly connected, plug the charger into a 120 volt AC outlet and the charger willshow “000” on the Digital Display, indicating power has been applied. Select the proper charge current ratebased on battery size. Press the 4/10/20/40 AMP button and t...

Page 9 - Engine Start; The Engine Start function can supply 110 amps for engine starting.; Recondition Mode

8 WARNING: BURST HAZARD: • NEVER EQUALIZE A GEL OR AGM BATTERY, these may burst and cause SERIOUS INJURY and propertydamage.• Remove or disconnect the vehicle’s battery when equalizing.The frequency which the equalization process needs to be run depends on the use of the battery. The more thebattery...

Page 10 - APPROXIMATE CHARGING TIMES; 0 Amp SmartTM Battery Charger; TROUBLESHOOTING

9 Remove or disconnect the vehicle’s battery when reconditioning. 1. Make sure the charger is in initiation state with a circulating pattern on the display or in charge OFF mode with “000” on the display. If not, press 4/10/20/40 AMP button repeatedly until “000” shows on the display. 2. Press the B...

Page 11 - Alternator output voltage is out of typical operation range.; CARE AND MAINTENANCE; With proper care and minimal maintenance, the

10 F01 — Internal Shorted Cell Battery If the battery being charged has an internal shorted cell, the F01 will show. We recommend taking your batteryto a certified automotive service center for evaluation. F02 — Bad Battery Connection or Battery Voltage Too Low to Accept Charge When F02 appears, the...

Page 12 - Accessories; SERVICE INFORMATION; FREE WARNING LABEL REPLACEMENT:; If your warning labels become illegible or are missing, call 1-800-; SPECIFICATIONS

11 Accessories Recommended accessories for use with your tool are available from your local dealer or authorized servicecenter. If you need assistance regarding accessories, please call: 1-800-544-6986. WARNING: The use of any accessory not recommended for use with this tool could be hazardous SERVI...