B&K AV2600 - Manuals

B&K AV2600 – Manual in PDF format online.

Manuals:

Manual

Manual B&K AV2600

Summary

Page 2 - ii; Phone

ii B&K Components, Ltd. , 2100 Old Union Road, Buffalo New York 14227-2725 Phone 1-800-543-5252 or (716) 656-0026, Fax (716) 656-1291 E-mail: [email protected] Web: www.bkcomp.com

Page 3 - iii; TABLE OF CONTENTS

iii TABLE OF CONTENTS Table of Contents...................................................................................................................................iii Safety Precautions ..............................................................................................................

Page 4 - SAFETY PRECAUTIONS; PLEASE READ BEFORE INSTALLING

1 SAFETY PRECAUTIONS PLEASE READ BEFORE INSTALLING WARNING: to prevent fire or shock hazard, do not expose this unit to rain or moisture. Care should be taken to prevent objects or liquid from entering the enclosure. Never handle the power cord with wet hands. • The lightning flash with arrowhead, w...

Page 5 - Toroidal Transformer

2 PURPOSE AND FUNCTION The AV2600 is an integration of a stereo audio distribution BUS with six compact and efficient 60 W power amplifiers. Each pair of amplifiers have DIP switches that allow system configuration for use with either mono/stereo and muting control via a Master or Local control inpu...

Page 6 - REAR PANEL VIEW; Figure 1

3 REAR PANEL VIEW V O LTA G E A . C . L I N E F U S E C A U T I O N : F O R C O N T I N U E DP R O T E C T I O N A G A I N S T R I S KO F F I R E R E P L A C E O N LYW I T H S A M E T Y P E 1 5 A 2 5 0 V. O U T 6 P L U S P L U S P L U S P L U S P L U S M I N U S M I N U S M I N U S M I N U S M I N U...

Page 7 - DIP SWITCH SETTING

4 DIP SWITCH SETTING Each pair of amplifiers have their own set of four DIP switches. The function of each switch is described below: AMP ON: (ON is the factory default setting for all amplifier pairs) Amplifier pairs with DIP switch ‘AMP’ set to ‘ON’, have the remote Master and Channel switching of...

Page 8 - CTRL OUT; CTRL IN; LEVEL CONTROL; Higher; Figure 2

5 CHANNEL CONTROL & MUTING Each pair of amplifier channels has its own 1/8” mini control input / output (pass through) jack to provide remote switching of the amplifier audio mute on/off feature. The control input circuit is designed to work as Tip Pos. (+) and Ring Neg. (-). A minimum of 5VDC @...

Page 9 - INPUT CONNECTIONS; Figure 3; OUTPUT CONNECTIONS; Figure 4; Figure 5

6 INPUT CONNECTIONS Each pair of amplifier channels have their own ‘Local’ input and output RCA connectors. The inputs are designed to accept line level audio from a preamplifiers unbalanced output connectors. Output expansion is accommodated with the supplied output connectors. These outputs are ef...

Page 10 - LEVEL CONTROL DEFEAT; JUMPER SETTINGS; JUMPER; VOL; Figure 7

7 LEVEL CONTROL DEFEAT The following procedures should only be performed by a qualified technician. Each pair of amplifier channels have their own ‘Local’ level control that may be bypassed to allow paralleling output channels. The jumper modules are located inside the unit, on the circuit board, ju...

Page 11 - Figure 8; FROM PREAMPLIFIER LEFT OUTPUT

8 HIGH CURRENT (MONO) USAGE The AV2600 has up to six output channels that may be paralleled (mono). This feature allows the amplifier to increase its output power into lower impedance speakers. Set all ‘AMP ON’, ‘L + R’ and ‘BUS’ DIP switches to the ‘ON’ position for the desired channels. Set the ‘S...

Page 12 - not; Do not connect it to the AC power source yet!

9 SYSTEM INSTALLATION There will most likely be a number of cables involved in the installation of your home entertainment system. Preplanning is essential in order to maximize system efficiency. We recommend the following as a means of helping you reach that goal. Make a diagram of your proposed sy...

Page 13 - TROUBLESHOOTING; PROBLEM; If unit continues to blow power inlet fuses,; DO NOT USE A HIGHER RATED; please contact customer service to have the unit serviced.; CARE AND CLEANING

10 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION No sound (‘on’ LED not illuminated) 1. Power cord not plugged in. 2. Power off at AC source. 3. AC power inlet fuse blown or faulty 1. Reconnect power cord. 2. Check AC switch or fuse 3. Check for shorts or overloading No sound on some or a...

Page 14 - SPECIFICATIONS

11 SPECIFICATIONS Power Rating: 8 ohms 4 ohms 60 watts @ 1 kHz 80 watts @ 1 kHz THD (S+N) 0.09 % @ 1 kHz Frequency response 5 Hz – 45 kHz Input sensitivity 0.77 Volts Input impedance 33.2 k ohms Damping factor 80 Current (peak to peak) 16 Amps Slew rate 14 V / sec Dynamic headroom 1.0 dB S/N (A-weig...