BISSELL Proheat2x 9500-p- Manuals

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 A ssembly 6 O perations Your ProHeat 2X CleanShot comes in three, easy to assemble components: Upper Handle Lower Handle Tool Caddy The only thing you will need to assemble your cleaner is a Phillips head screwdriver.1. slide upper handle onto lo...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 7 O perations Custom Clean ® the custom clean feature automatically mixes hot tap water with the bissell formula. simply choose one of the 4 settings (heavy traffic, normal clean, light clean, or water rinse) and the ProHeat 2X cleanshot Professi...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 O perations 8 ReadyTools™ dial this provides either floor cleaning or above floor cleaning with the turn of a knob. choose "tools" setting for stairs, upholstery and hard to reach areas and "flooR cleaning" for carpets area rugs a...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 9 O perations Before you clean 1. Move furniture to another area if cleaning an entire room (optional). 2. Pick up all loose dirt, debris, and pet hair before deep cleaning. if you are cleaning just a small area of carpeting or less than a whole ...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 O perations 10 Carpet cleaning 1. fill the 2-in-1 Water tank. Remove the tank from the base of the machine by lifting up the tank carry handle. carry like a bucket to the sink. 1a. unlatch the top of the tank from the bottom by lifting up on the ...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 11 O perations Carpet cleaning continued 6. Plug into a proper outlet and turn the power and heater switches to the on ( i ) position. allow 1 minute for the built-in heater to warm-up before cleaning. the ProHeat 2X will be fully warmed and will...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 13 O perations Cleaning with attachments Your ProHeat 2X machine comes equipped with a hose and at least one attachment for cleaning stairs, upholstery, and more.1. Important! if using to clean uphol- stery, check upholstery tags. A. check manufa...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 O perations 14 8. Remove and rinse tools in clean, running water. dry and replace in the tool caddy. 9. it is recommended that you suction clean water from a bowl to rinse out the hose. 10. before replacing lift end of hose and stretch out to ens...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 15 O perations Stain removal Do Not Delay! Attending to an accident soon after it occurs ensures the most optimal clean. Leaving it for an extended period of time may cause it to set and become permanent.1. blot up liquids with an absorbent cloth...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 O perations 16 Hard floor cleaning Your ProHeat 2X model may have come with a hard floor attachment and 2X Hard Floor Solutions Formula. If not, these products are available for purchase by contacting the BISSELL Consumer Care department by phone...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 17 M aintenance and care Machine storage once your cleaning is complete, make sure the 2-in-1 water tank is emptied, rinsed out, and dried before the next use. the formula tank can remain filled and ready to go. Note: Store cleaner in a protected...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 M aintenance and care 18 Machine care continued 6. the inside of the end caps by the brush rolls can be wiped out with a clean paper towel, or, if a more thorough cleaning is desired, the end caps can be taken off using a Phillips head screwdrive...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 19 M aintenance and care Brushes can be removed for cleaning or replacement as needed. 1. follow small belt removal instructions on page 18. 2. Remove brush rolls by pulling them off of the metal rods. 3. Place cleaned or new brush rolls back ont...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 T roubleshooting w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 20 Built-in heater ready light does not illuminate Possible causes Remedies 1. The heater switch is not turned ON ( I ) 1. Turn the heater switch ON ( I ) 2. The power switch ...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 21 R eplacement parts - BISSELL ProHeat 2X Below please find a list of common replacement parts. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. Item Part No. Part Name 1 2...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 A ccessories - BISSELL ProHeat 2X 22 Below please find a list of common accessories. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. Item Part No. Part Name 1 203-6651 3” t...

w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1 23 W arranty - BISSELL ProHeat 2X this warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. if you need additional instruction regarding this warranty or have questions regarding what it...

©2012 bissell Homecare, inc grand Rapids, michigan all rights reserved. Printed in china Part number 120-4450 Rev 4/12 Visit our website at: www.bissell.com scotchgard is a trademark of 3m For information about repairs or replacement parts, or questions about your warranty, call: BISSELL Consumer Ca...