BISSELL 73G8 - Manuals - manualsarea.com

Page 2 - comprehensive one-year warranty. We also stand behind it with a; How To Use This Guide; Plastic film can be

2 Thanks For Buying A BISSELL CleanView ® II We’re glad you purchased a BISSELL CleanView II Vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home vacuuming system.Your BISSELL CleanView II is well made, and we back it with a limited compr...

Page 3 - IMPORTAnT SAFETy InSTRUCTIOnS; READ ALL InSTRUCTIOnS; To reduce; SAVE THESE; THIS APPLIAnCE HAS

3 IMPORTAnT SAFETy InSTRUCTIOnS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL InSTRUCTIOnS BEFORE USInG yOUR UPRIGHT VACUUM. Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and befo...

Page 5 - How To Put It Together; Select Models Only; The only tool you’ll need to assemble your vacuum; Attach Handle To Vacuum

5 How To Put It Together Select Models Only The only tool you’ll need to assemble your vacuum cleaner is a screwdriver. Locate the vacuum Handle and remove the screw packet taped to the base of the Handle. Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top o...

Page 6 - Height Adjustment; How To Use your Vacuum; Handle Positions

Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. Upright- For storage and above floor cleaning with tools. Normal Cleaning- Press Handle Release Pedal once. Use for most household floor cleaning tasks. Low Cleaning- With the vacuum in normal clea...

Page 7 - Special On-Board Tools; Power Cord Storage

Your BISSELL CleanView II is not only a pow- erful carpet and rug vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools. Raise Handle to Upright Position. Grasp the Quick Reach Handle and lift Hose Wand to separate from suction intake opening. Atta...

Page 8 - How To Maintain your Vacuum; Empty Dirt Container; Full Line; Cleaning The Inner & Outer Circular Filters

To maintain maximum cleaning performance, the following maintenance steps must be performed: Empty the Dirt Container when the dirt reaches the “Full” line on the side. Check the Inner and Outer Circular Filters and the Pre-Motor Filter at least once a month and clean or replace as needed. Replace t...

Page 9 - Check Rotating Floor Brush and Drive Belt

Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water. Mild detergent may be used if desired. Rinse well, then air dry thoroughly before putting them back together and replacing in Filter Cup. The Filter Cup may be washed in warm water with a mild d...

Page 10 - in your BISSELL CleanView II.; Replace Drive Belt; Motor Pulley; Replace Lightbulb; Brush Cover; Check Rotating Floor Brush and Drive Belt Continued; Wide Cleaning Path models only

For standard models , remove the four screws as shown with a Phillips Head Screwdriver. Lift the Brush Cover off. For wide cleaning path models , Lift tab 1 and release the three latches in order 2-4 as marked. Lift the Brush Cover off. Grasp Rotating Floor Brush at both ends and lift. Clean strings...

Page 11 - Replace Lightbulb Continued; Standard Bulb; Clearing Clogs; Belt Cover

Determine the light bulb type of your vacuum: Standard Bulb (#203-1297) – approximately 1” long, flat end Large Bulb (#203-1007) – approximately 2” long, round end Standard Bulb – remove the bulb from the socket by grasping bulb and pulling straight out. Install the new bulb by pushing it gently int...

Page 12 - Troubleshooting; Vacuum cleaner won’t run; Vacuum cleaner won’t pick up dirt; Possible Causes; To reduce the risk of injury from moving; Suction Inlet; Clearing Clogs Continued

12 Troubleshooting Vacuum cleaner won’t run Possible Causes Remedies Power cord not plugged in Check electrical plug Blown fuse/tripped breaker Check/Replace fuse or reset breaker Vacuum cleaner won’t pick up dirt Possible Causes Remedies Incorrect Height Adjustment Adjust Powerfoot to correct heigh...

Page 13 - Troubleshooting Continued

Vacuum cleaner won’t pick up dirt continued Possible Causes Remedies Dirt Container not installed properly Position correctly and lock in place Filters are dirty Check and clean Inner and Outer Circular Filters, Pre-Motor and Post-Motor Filters Louvers missing or installed incorrectly Check for a cl...

Page 14 - Replacement Parts – BISSELL Cleanview II Series; MasterCard, Discover or American Express, call; BISSELL Consumer Services; Saturday; Part name

14 Replacement Parts – BISSELL Cleanview II Series 1 2/3 4 7 5 6 8/9 10 11 12 14 15 16 17 13 7 You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services or by visiting our website. To locate a retailer near you, or to place an order using Visa, MasterCard, Discover ...

Page 15 - For information about repairs or replacement parts, or; nOTE: Please keep your original sales receipt. It is your warranty.

BISSELL Consumer Services For information about repairs or replacement parts, or questions about your warranty, call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare Inc. PO Box 3606 Grand Rapids, MI 49501 ATTN: Cons...

Page 16 - Warranty; Limited One year Warranty; If your BISSELL product should require service:

Warranty 16 This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, o...